Code for creating single byte llis is present at several places. Create a
routine to avoid code redundancy.
Also, we don't need one lli per single byte transfer, we can have single lli to
do all single byte transfer.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
max_bytes_per_lli = bd.srcbus.buswidth * PL080_CONTROL_TRANSFER_SIZE_MASK;
This is confirmed by ARM support guys.
Below is summary of mail exchange with them:
[Viresh] What is the total data to be transferred in case source and destination
bus widths are different. Suppose, source bus width is 2 bytes and destination
is 4 bytes. Now in order to transfer 80 bytes, what should be value of
TransferSize field in control reg: 40? or 20?.
[David from ARM] The value that is programmed into the TransferSize field should
be the number of <SourceWidth> transfers needed to achieve the required data
transfer.
So, to transfer 80 bytes, with a Source Width of 2, the TransferSize field =
should be programmed with:
Total transfer size
------------------- = 40
<source width>
[Viresh] Will this change if source is 4 bytes and dest is 2?
[David] Yes - the calculation then becomes:
Total transfer size
------------------- =20
<source width>
Also, max_bytes_per_lli must be calculated after fixing src and dest widths not
before that. So move this code to the correct place.
This patch also removes max_bytes_per_lli from earlier print message, as till
that point max_bytes_per_lli is unknown.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pl080 Manual says: "Bursts do not cross the 1KB address boundary"
We can program the controller to cross 1 KB boundary on a burst and controller
can take care of this boundary condition by itself.
Following is the discussion with ARM Technical Support Guys (David):
[Viresh] Manual says: "Bursts do not cross the 1KB address boundary"
What does that actually mean? As, Maximum size transferable with a single LLI is
4095 * 4 =16380 ~ 16KB. So, if we don't have src/dest address aligned to burst
size, we can't use this big of an LLI.
[David] There is a difference between bursts describing the total data
transferred by the DMA controller and AHB bursts. Bursts described by the
programmable parameters in the PL080 have no direct connection with the bursts
that are seen on the AHB bus.
The statement that "Bursts do not cross the 1KB address boundary" in the TRM is
referring to AHB bursts, where this limitation is a requirement of the AHB spec.
You can still issue bursts within the PL080 that are in excess of 1KB. The
PL080 will make sure that its bursts are broken down into legal AHB bursts which
will be formatted to ensure that no AHB burst crosses a 1KB boundary.
Based on above discussion, this patch removes all code related to 1 KB boundary
as we are not required to handle this in driver.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently, if error interrupt occurs, nothing is done in interrupt handler (just
clearing the interrupts). We must somehow indicate this to the user that DMA is
over, due to ERR interrupt or TC interrupt.
So, this patch just schedules existing tasklet, with a print showing error
interrupt has occurred on which channels.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We have just executed following in pl08x_get_phy_channel():
ch->signal = -1;
We don't have to compare "ch->signal < 0", as this will always be true.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Simply writing 1 on bit 0 is sufficient instead of reading and clearing bits.
Also as per manual, for bit 3-31 of DMACConfiguration register:
"read undefined, write as 0"
So, we must not rely on values read from this registers bit 3-31.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Insert notifiers for the runtime PM API. With this the runtime PM layer kicks in
to action where used.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
For 8 memory and 16 slave channels 35 boot print lines are printed. And that is
too much. Most of this would be more useful for debugging. So moving few of them
to dev_dbg instead of dev_info. Now only 3 prints will be printed.
This also rearrange one of the debug message to fit into two lines.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Similar comment is present over routine also pl08x_choose_master_bus(). Keeping
one of them. Also rewrite that comment to convey message clearly.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As mentioned in Documentation/CodingStyle,
The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not.
This patch replaces (struct xyz) with *ptr at several occurrences in driver.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Header files included in driver are not present in alphabetical order. Rearrange
them in alphabetical order.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There were few formatting related issues in code. This patch fixes them.
Fixes include:
- Remove extra blank lines
- align code to 80 cols
- combine several lines to one line
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
<asm/hardware/pl080.h> doesn't have protection to deal with multiple inclusion.
And so we get compilation errors in cases where this file is included more than
once. This patch adds #ifdefs at the top of file to protect it against multiple
inclusions.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit c03f007a8b (OMAP: PM:
omap_device: add system PM methods for PM domain handling) mistakenly
used SET_SYSTEM_SLEEP_PM_OPS() when trying to configure custom methods
for the PM domains noirq methods. Fix that by setting only the
suspend_noirq and resume_noirq methods with custom versions.
Note that all other PM domain methods (including the "normal"
suspend/resume methods) are populated using USE_PLATFORM_PM_SLEEP_OPS,
which configures them all to the default subsystem (platform_bus)
methods.
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The description of pm_runtime_irq_safe() has to be updated to follow
the code after commit 02b2677 (PM / Runtime: Allow _put_sync() from
interrupts-disabled context).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
Headphones has stopped working for the original reported (a regression
compared to 2.6.38). This is because Speaker and Headphones share the
same DAC, in which case no Headphones volume control was created.
This patch fixes so that both Speaker and Headphones volume
controls are created in such scenario.
BugLink: http://bugs.launchpad.net/bugs/817943
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In commit a144c6a6c9 ("PM: Print a warning if firmware is requested
when tasks are frozen") we not only printed a warning if somebody tried
to load the firmware when tasks are frozen - we also failed the load.
But that check was done before the check for built-in firmware, and then
when we disallowed usermode helpers during bootup (commit 288d5abec8:
"Boot up with usermodehelper disabled"), that actually means that
built-in modules can no longer load their firmware even if the firmware
is built in too. Which used to work, and some people depended on it for
the R100 driver.
So move the test for usermodehelper_is_disabled() down, to after
checking the built-in firmware.
This should fix:
https://bugzilla.kernel.org/show_bug.cgi?id=40952
Reported-by: James Cloos <cloos@hjcloos.com>
Bisected-by: Elimar Riesebieter <riesebie@lxtec.de>
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Rafael Wysocki <rjw@sisk.pl>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-31-rc3/i2c-fixes' of git://git.fluff.org/bjdooks/linux:
i2c-nomadik: fix kerneldoc warning
Revert "i2c-omap: fix static suspend vs. runtime suspend"
i2c-nomadik: Do not use _interruptible_ variant call
There was a missing struct item in the kerneldoc, add it and fix
another pretty-printing formatting issue with a missing space.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Seen on v3.1-rc3, patch:
omap: mcbsp: Drop in-driver transfer support
bafe2721a0
Removed code that now cause tidspbridge to break while compiling.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Associate the HDMI clock together with LCDC1 on sh7372.
Without this patch Suspend-to-RAM hangs on the boards
AP4EVB and Mackerel. The code hangs in the LCDC driver
where the software is waiting forever for the hardware to
power down. By explicitly associating the HDMI clock with
LCDC1 we can make sure the HDMI clock is enabled using
Runtime PM whenever the driver is accessing the hardware.
This HDMI and LCDC1 dependency is documented in the sh7372
data sheet. Older kernels did work as expected but the
recently merged (3.1-rc)
794d78f drivers: sh: late disabling of clocks V2
introduced code to turn off clocks lacking software reference
which happens to include the HDMI clock that is needed by
LCDC1 to operate as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since sci_port_enable() and sci_port_disable() may be run with
interrupts off and they execute pm_runtime_get_sync() and
pm_runtime_put_sync(), respectively, the SCI device's
power.irq_safe flag has to be set to indicate that it is safe
to execute runtime PM callbacks for this device with interrupts off.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The lock member of struct pm_clk_data is of type struct mutex,
which is a problem, because the suspend and resume routines
defined in drivers/base/power/clock_ops.c cannot be executed
with interrupts disabled for this reason. Modify
struct pm_clk_data so that its lock member is a spinlock.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wiimote: Add status and return request handlers
HID: wiimote: Add drm request
HID: wiimote: Register led class devices
HID: wiimote: Correctly call HID open/close callbacks
HID: wiimote: Simplify synchronization
HID: usbhid: Add support for SiGma Micro chip
HID: add support for new revision of Apple aluminum keyboard
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ad714x - read the interrupt status registers in a row
Input: ad714x - use DMA-safe buffers for spi_write()
Input: ad714x - fix endianness issues
Input: ad714xx-spi - force SPI bus into the default 8-bit mode
Input: ep93xx_keypad - add missing include of linux/module.h
Input: tnetv107x-ts - add missing include of linux/module.h
Input: max11801_ts - correct license statement
Input: atmel_mxt_ts - report pressure information from the driver
Input: bcm5974 - Add support for newer MacBookPro8,2
Input: wacom - report id 3 returns 4 bytes of data
Input: wacom - add WAC_MSG_RETRIES define
Input: wacom - add support for the Wacom Bamboo Pen (CTL-660/K)
Input: tegra-kbc - correct call to input_free_device
Input: mpu3050 - correct call to input_free_device
Input: bcm5974 - add support for touchpads found in MacBookAir4,2
Input: mma8450 - fix module device table type
Input: remove CLOCK_TICK_RATE from analog joystick driver
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: check size of FUSE_NOTIFY_INVAL_ENTRY message
fuse: mark pages accessed when written to
fuse: delete dead .write_begin and .write_end aops
fuse: fix flock
fuse: fix non-ANSI void function notation
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
bridge: fix a possible net_device leak
net: Documentation: RFC 2553bis is now RFC 3493
atm: br2684: Fix oops due to skb->dev being NULL
ipv6: Fix ipv6_getsockopt for IPV6_2292PKTOPTIONS
net: netdev-features.txt update to Documentation/networking/00-INDEX
vlan: reset headers on accel emulation path
forcedeth: call vlan_mode only if hw supports vlans
via-velocity: remove non-tagged packet filtering
bonding:reset backup and inactive flag of slave
net_sched: fix port mirror/redirect stats reporting
sit tunnels: propagate IPv6 transport class to IPv4 Type of Service
gianfar: reduce stack usage in gianfar_ethtool.c
net: minor update to Documentation/networking/scaling.txt
net: add missing entries to Documentation/networking/00-INDEX
gianfar: prevent buggy hw rx vlan tagging
net: sh_eth: Fix build by forgot including linux/interrupt.h
drivers/net/can/sja1000/plx_pci.c: eliminate double free
usbnet/cdc_ncm: Don't use stack variables for DMA
vmxnet3: Don't enable vlan filters in promiscuous mode.
iwlagn: sysfs couldn't find the priv pointer
...
Make sure that only assigned storage increments are unassigned when
attaching a storage element.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The main purpose for PSW restart will be kdump. Therefore customers will
issue "system restart" for creating a dump. If kdump is not enabled,
currently "PSW restart" will reboot the system and then no dump can
be created any more. In order to still allow a manual stand-alone dump in
the case a user issues "PSW restart" on a system that has not enabled
kdump we now stop the system.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
reipl_fcp_kset was just initialized, so it appears that it should be tested
instead of reipl_kset.
Signed-off-by: Julia Lawall <julia@diku.dk>
Reported-by: Suman Saha <sumsaha@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Data is only used to temporarily hold information to be copied to the user
level, so it should be freed before leaving the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When IPL'ing from a block device and an NSS should be created we must
make sure that the kernel image and the initrd are in different 1MB
segments. Otherwise creating the NSS will fail.
So we make sure the initrd is 4MB behind the end of the kernel image
like we do already when IPL via the VM reader is performed.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Board file support for Ventana is not yet mainlined, and probably won't
ever be given the move to Device-Tree. Consequently, the Ventana entry
is being removed from arch/arm/tools/mach-types in the next merge window,
since it was registered over a year ago.
This will also remove function machine_is_ventana(), which is used by
the ASoC Tegra WM8903 machine driver. This will cause compilation
failures. Drop Ventana support to resolve this.
Hopefully, in the not-too-distant future, tegra_wm8903.c will be able to
configure itself from Device-Tree, and hence we'll be able to re-instate
Ventana support just by creating a .dts file for the board.
Also note that Aebl support is in a similar boat. However, that board
isn't scheduled for deprecation for at least another 5 months, and
perhaps we will have completely removed non-Device-Tree support from
tegra_wm8903.c by then and/or adjusted mach-types policy.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Joseph Pentland <jp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
FUSE_NOTIFY_INVAL_ENTRY didn't check the length of the write so the
message processing could overrun and result in a "kernel BUG at
fs/fuse/dev.c:629!"
Reported-by: Han-Wen Nienhuys <hanwenn@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@kernel.org
Function i5k_channel_pci_id looks like it can fail, while a better
code design would make it more obvious that it can't. We can even get
rid of the function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, vdso: On system call restart after SYSENTER, use int $0x80
x86, UV: Remove UV delay in starting slave cpus
x86, olpc: Wait for last byte of EC command to be accepted
When we enter a 32-bit system call via SYSENTER or SYSCALL, we shuffle
the arguments to match the int $0x80 calling convention. This was
probably a design mistake, but it's what it is now. This causes
errors if the system call as to be restarted.
For SYSENTER, we have to invoke the instruction from the vdso as the
return address is hardcoded. Accordingly, we can simply replace the
jump in the vdso with an int $0x80 instruction and use the slower
entry point for a post-restart.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/CA%2B55aFztZ=r5wa0x26KJQxvZOaQq8s2v3u50wCyJcA-Sc4g8gQ@mail.gmail.com
Cc: <stable@kernel.org>
I looks like something used to implicitly include linux/interrupt.h,
and no longer does. Fix the resulting build error by explicitly
including it.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"ret" needs to be signed for the error handling to work properly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
zcache_put_page() was modified to pass page_address(page) instead of the
actual page structure. In combination with the function signature changes
to tmem_put() and zcache_pampd_create(), zcache_pampd_create() tries to
(re)derive the page structure from the virtual address. However, if the
original page is a high memory page (or any unmapped page), this
virt_to_page() fails because the page_address() in zcache_put_page()
returned NULL.
This patch changes zcache_put_page() and zcache_get_page() to pass
the page structure instead of the page's virtual address, which
may or may not exist.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes fallout due to the removal of the cast in commit aa462abe8a
("mm: fix __page_to_pfn for a const struct page argument")
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to missing memset function declaration.
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the arrival of kernel version 3.0 in the staging tree it
turns out compile error occurs for sparc64, powerpc, and arm
platforms. This patch fixes that issue.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Henry Ptasinski <henryp@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
