This patch will set the correct bits to turn on Aggressive
Link Power Management (ALPM) for the ahci driver. This
will cause the controller and disk to negotiate a lower
power state for the link when there is no activity (see
the AHCI 1.x spec for details). This feature is mutually
exclusive with Hot Plug, so when ALPM is enabled, Hot Plug
is disabled. ALPM will be enabled by default, but it is
settable via the scsi host syfs interface. Possible
settings for this feature are:
Setting Effect
----------------------------------------------------------
min_power ALPM is enabled, and link set to enter
lowest power state (SLUMBER) when idle
Hot plug not allowed.
max_performance ALPM is disabled, Hot Plug is allowed
medium_power ALPM is enabled, and link set to enter
second lowest power state (PARTIAL) when
idle. Hot plug not allowed.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Device Initiated Power Management, which is defined
in SATA 2.5 can be enabled for disks which support it.
This patch enables DIPM when the user sets the link
power management policy to "min_power".
Additionally, libata drivers can define a function
(enable_pm) that will perform hardware specific actions to
enable whatever power management policy the user set up
for Host Initiated Power management (HIPM).
This power management policy will be activated after all
disks have been enumerated and intialized. Drivers should
also define disable_pm, which will turn off link power
management, but not change link power management policy.
Documentation/scsi/link_power_management_policy.txt has additional
information.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The recent fix to host reset introduced a problem, whereby AHCI-enable
bit would be cleared upon reset, if it was not asserted prior to reset.
Unconditionally enable AHCI-enable bit.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MAXTOR 7V300F0/VA111900 does spurious NCQ completions. Add it to
blacklist. This problem is reported by Carsten Otto.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Carsten Otto <c-otto@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After reset, transfer mode is always PIO0 regardless of
dev->xfer_mask. Check dev->pio_mode before trying to slow down after
configuration failure. This prevents bogus speed down before device
is actually configured.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Forcing PIO0 on reset was done inside ata_bus_softreset(), which is a
bit out of place as it should be applied to all resets - hard, soft
and implementation which don't use ata_bus_softreset(). Relocate it
such that...
* For new EH, it's done in ata_eh_reset() before calling prereset.
* For old EH, it's done before calling ap->ops->phy_reset() in
ata_bus_probe().
This makes PIO0 forced after all resets. Another difference is that
reset itself is done after PIO0 is forced.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code copied from drivers/ide/pci/ns87415.c uses this, so copy the
definition from there as well.
Fixes the following build error:
CC [M] drivers/ata/pata_ns87415.o
drivers/ata/pata_ns87415.c: In function ‘ns87560_read_buggy’:
drivers/ata/pata_ns87415.c:228: error: ‘SUPERIO_IDE_MAX_RETRIES’ undeclared (first use in this function)
drivers/ata/pata_ns87415.c:228: error: (Each undeclared identifier is reported only once
drivers/ata/pata_ns87415.c:228: error: for each function it appears in.)
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On certain device/controller combination, 0xff status is asserted
after reset and doesn't get cleared during 150ms post-reset wait. As
0xff status is interpreted as no device (for good reasons), this can
lead to misdetection on such cases.
This patch implements ata_wait_after_reset() which replaces the 150ms
sleep and waits upto ATA_TMOUT_FF_WAIT if status is 0xff.
ATA_TMOUT_FF_WAIT is currently 800ms which is enough for
HHD424020F7SV00 to get detected but not enough for Quantum GoVault
drive which is known to take upto 2s.
Without parallel probing, spending 2s on 0xff port would incur too
much delay on ata_piix's which use 0xff to indicate empty port and
doesn't have SCR register, so GoVault needs to wait till parallel
probing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA devices in SLEEP mode don't respond to any commands. SRST is
necessary to wake it up. Till now, when a command is issued to a
device in SLEEP mode, the command times out, which makes EH reset the
device and retry the command after that, causing a long delay.
This patch makes libata track SLEEP state and issue SRST automatically
if a command is about to be issued to a device in SLEEP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bruce Allen <ballen@gravity.phys.uwm.edu>
Cc: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some commands need post-processing after successful completion. This
was done in ata_scsi_qc_complete() till now but this has the following
problems.
* Post-command processing gets executed when qc is completed from EH.
Some qc's are retried from EH with zero err_mask and thus triggers
unnecessary/incorrect post-command processing.
* Command post processing doesn't belong to SAT layer.
* Link-wide revalidation was scheduled where device revalidation
suffices.
This patch moves post-command processing to success completion path of
ata_qc_complete() which is travelled iff the command is going to be
completed without passing through EH and updates post-command
processing such that device-specific action is used. While at it,
restructure code a bit for readability.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'sg' of git://git.kernel.dk/linux-2.6-block:
fix sg_phys to use dma_addr_t
ub: add sg_init_table for sense and read capacity commands
x86: pci-gart fix
blackfin: fix sg fallout
xtensa: dma-mapping.h is using linux/scatterlist.h functions, so include it
SG: audit of drivers that use blk_rq_map_sg()
arch/um/drivers/ubd_kern.c: fix a building error
SG: Change sg_set_page() to take length and offset argument
AVR32: Fix sg_page breakage
mmc: sg fallout
m68k: sg fallout
More SG build fixes
sg: add missing sg_init_table calls to zfcp
SG build fix
I guess Windows didn't care about the command so neither did they
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
P5W-DH Deluxe has ICH9 which doesn't have PMP support but SIMG 4726
hardwired to the second port of AHCI controller at PCI device 1f.2.
The 4726 doesn't work as PMP but as a storage processor which can do
hardware RAID on downstream ports.
When no device is attached to the downstream port of the 4726, pseudo
ATA device for configuration appears. Unfortunately, ATA emulation on
the device is very lousy and causes long hang during boot.
This patch implements workaround for the board. If the mainboard is
P5W-DH Deluxe (matched using DMI), only hardreset is used on the
second port of AHCI controller @ 1f.2 and the hardreset doesn't depend
on receiving the first FIS and just proceed to IDENTIFY.
This workaround fixes bugzilla #8923.
http://bugzilla.kernel.org/show_bug.cgi?id=8923
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Local variable @action usage in ata_eh_reset() is a bit confusing.
It's used only to cache ehc->i.action to test reset masks after
clearing it; however, due to the generic name "action", it's easy to
misinterpret the local variable as containing the selected reset
method later. Also, the reason for caching the original value is easy
to miss.
This patch renames @action to @tmp_action and make it buffer newly
selected value instead to improve readability.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.
Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Another one doing spurious NCQ completions. Blacklist it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Did a complete audit of these and found we have another error case.
ata_bus_softreset calls ata_check_status which means that it tries to do
an ioread8 on the port blindly and check versus 0xFF for an error.
It should of course be using the ap->ops method for this via chk_status,
and this bug causes a wrog status call on the NS87415 at least.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tackle the relatively sane complaints of checkpatch --file.
The vast majority is indentation and whitespace changes, the rest are
* #include fixes
* printk KERN_xxx prefix addition
* BSS/initializer cleanups
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (74 commits)
fix do_sys_open() prototype
sysfs: trivial: fix sysfs_create_file kerneldoc spelling mistake
Documentation: Fix typo in SubmitChecklist.
Typo: depricated -> deprecated
Add missing profile=kvm option to Documentation/kernel-parameters.txt
fix typo about TBI in e1000 comment
proc.txt: Add /proc/stat field
small documentation fixes
Fix compiler warning in smount example program from sharedsubtree.txt
docs/sysfs: add missing word to sysfs attribute explanation
documentation/ext3: grammar fixes
Documentation/java.txt: typo and grammar fixes
Documentation/filesystems/vfs.txt: typo fix
include/asm-*/system.h: remove unused set_rmb(), set_wmb() macros
trivial copy_data_pages() tidy up
Fix typo in arch/x86/kernel/tsc_32.c
file link fix for Pegasus USB net driver help
remove unused return within void return function
Typo fixes retrun -> return
x86 hpet.h: remove broken links
...
sata_sis has the same restrictions as other SFF controllers, and so must
use LIBATA_MAX_PRD to denote that SCSI may only fill ATA_MAX_PRD/2
entries, due to our need to handle IOMMU merging.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SCR read for controllers which uses PCI configuration space for SCR
access got broken while adding @val argument to SCR accessors. Fix
it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix libata kernel-doc parameter name.
Warning(linux-2.6.23-git13//drivers/ata/libata-core.c:1415): No description found for parameter 'sgl'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] kill ata_sg_is_last()
Update libata driver for bf548 atapi controller against the 2.6.24 tree.
libata-sff: Correct use of check_status()
drivers/ata: add support to Freescale 3.0Gbps SATA Controller
pata_acpi: fix build breakage if !CONFIG_PM
Get rid of sparse related warnings from places that use integer as NULL
pointer.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Short term, this works around a bug introduced by early sg-chaining
work.
Long term, removing this function eliminates a branch from a hot
path loop in each scatter/gather table build. Also, as this code
demonstrates, we don't need to _track_ the end of the s/g list, as
long as we mark it in some way. And doing so programatically is nice.
So its a useful cleanup, regardless of its short term effects.
Based conceptually on a quick patch by Jens Axboe.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_check_status() does an SFF compliant check
ata_chk_status() does a generic call to ap->ops->check_status (usually
ata_check_status)
libata-sff uses the wrong one. Hardly suprising given the naming here,
which ought to get fixed to ata_sff_check_status() perhaps ?
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for Freescale 3.0Gbps SATA Controller supporting
Native Command Queueing(NCQ), device hotplug, and ATAPI. This controller
can be found on MPC8315 and MPC8378.
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are configurations where CONFIG_ACPI but !CONFIG_PM. In this
case, pata_acpi can be selected but won't build. Fix it.
Reported by Avuton Olrich.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Avuton Olrich <avuton@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
LIBATA_MAX_PRD is the maximum number of DMA scatter/gather elements
permitted by the HBA's DMA engine. It's properly set to
q->max_hw_segments via the sg_tablesize parameter.
libata shouldn't call blk_queue_max_phys_segments. Now LIBATA_MAX_PRD
is equal to SCSI_MAX_PHYS_SEGMENTS by default (both is 128), so
everything is fine. But if they are changed, some code (like the scsi
mid layer, sg chaining, etc) might not work properly.
(Addition from Jens) The basic issue is that the physical segment
setting is purely a driver issue. And since SCSI is managing the sglist,
libata has no business changing the setting. All libata should care
about is the hw segment setting.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This converts libata to using the sg helpers for looking up sg
elements, instead of doing it manually.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix libata docbook warnings.
Warning(linux-2.6.23-git8//drivers/ata/libata-scsi.c:3251): No description found for parameter 'dev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The strn_pattern_cmp routine does not handle a blank name parameter
properly. The only patterns which should match a blank name are "*"
and an explicit "". If the function is passed a blank name in current
code, it will always match against the patt parameter. The bug manifests
itself as the device with the empty model name always matching the first
device in the DMA blacklist, forcing it to revert to PIO mode.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds a port map for ICH9 and ICH8 SATA controllers that have only 2 ports available in that mode.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a driver for the ATA controller on the Geode CS5536 companion
chip. The PCI device ID for this device was previously claimed by
pata_amd.c but the PIO timings were not correct. This driver also
works around a bug in some BIOSes that handle unaligned access to the
PCI config registers poorly. Finally, the driver allows fallback to
using MSR registers for configuration on BIOSes that are truly
broken.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
