Before this patch, ACPI_STATE_D3 incorrectly referenced D3hot
in some places, but D3cold in other places.
After this patch, ACPI_STATE_D3 always means ACPI_STATE_D3_COLD;
and all references to D3hot use ACPI_STATE_D3_HOT.
ACPI's _PR3 method is used to enter both D3hot and D3cold states.
What distinguishes D3hot from D3cold is the presence _PR3
(Power Resources for D3hot) If these resources are all ON,
then the state is D3hot. If _PR3 is not present,
or all _PR0 resources for the devices are OFF,
then the state is D3cold.
This patch applies after Linux-3.4-rc1.
A future syntax cleanup may remove ACPI_STATE_D3
to emphasize that it always means ACPI_STATE_D3_COLD.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enhanced the sleep/wake interfaces to optionally execute the
_GTS method (Going To Sleep), and the _BFS method (Back From
Sleep). Windows apparently does not execute these methods, and
therefore these methods are often untested. It has been seen on
some systems where the execution of these methods causes errors
and also prevents the machine from entering S5. It is therefore
suggested that host operating systems do not execute these methods
by default. In the future, perhaps these methods can be optionally
executed based on the age of the system and/or what is the newest
version of Windows that the BIOS asks for via _OSI.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Simplifies the code, especially the compile-time
ACPI_REDUCED_HARDWARE option.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add new notify values, add support for "hardware specific" notifies.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Support within the interpreter and operation region dispatch.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI_NO_HARDWARE_INIT is only used by acpi_early_init() and
acpi_bus_init() when calling acpi_enable_subsystem(), but
acpi_enable_subsystem() doesn't check that flag, so it can be
dropped.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
_SxW returns an Integer containing the lowest D-state supported in state
Sx. If OSPM has not indicated that it supports _PR3, then the value “3”
corresponds to D3. If it has indicated _PR3 support, the value “3”
represents D3hot and the value “4” represents D3cold.
Linux does set _OSC._PR3, so we should fix it to expect that _SxW can
return 4.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This change will force the execution of a _REG method underneath
the EC device even if there is no corresponding operation region
of type EmbeddedControl. Fixes a problem seen on some machines
and apparently is compatible with Windows behavior.
http://www.acpica.org/bugzilla/show_bug.cgi?id=875
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Moved to where the predefined regions are actually defined.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Moved this internal space id in preparation for ACPI 5.0 changes
that will include some new space IDs.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The global event handler is called whenever a general purpose
or fixed ACPI event occurs.
Also update Linux OSL to collect events counter with
global event handler.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This feature provides an automatic device notification for wake devices
when a wakeup GPE occurs and there is no corresponding GPE method or
handler. Rather than ignoring such a GPE, an implicit AML Notify
operation is performed on the parent device object.
This feature is not part of the ACPI specification and is provided for
Windows compatibility only.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The new GPE handler callback has 2 additional parameters, gpe_device and
gpe_number.
typedef
u32 (*acpi_gpe_handler) (acpi_handle gpe_device, u32 gpe_number, void *context);
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some function and variable names are renamed to be consistent with
ACPICA code base.
acpi_raw_enable_gpe -> acpi_ev_add_gpe_reference
acpi_raw_disable_gpe -> acpi_ev_remove_gpe_reference
acpi_gpe_can_wake -> acpi_setup_gpe_for_wake
acpi_gpe_wakeup -> acpi_set_gpe_wake_mask
acpi_update_gpes -> acpi_update_all_gpes
acpi_all_gpes_initialized -> acpi_gbl_all_gpes_initialized
acpi_handler_info -> acpi_gpe_handler_info
...
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move the 64-bit overlay structures to the utmath module since
they are used nowhere else. Update module comment. ACPICA BZ 829.
http://www.acpica.org/bugzilla/show_bug.cgi?id=829
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Change definition of acpi_thread_id to always be a u64. This
simplifies the code, especially any printf output. u64 is
the only common data type for all thread_id types across all
operating systems. We now force the OSL to cast the native
thread_id type to u64 before returning the value to ACPICA
(via acpi_os_get_thread_id).
Signed-off-by: Lin Ming <ming.m.lin@intel.com
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Adds install/remove interfaces so that the host can dynamically
alter the global _OSI table. Also adds support for _OSI handlers.
Additional support: new debugger command (osi), and test support in
the acpiexec utility. Adds new file, utilities/utosi.c.
ACPICA bugzilla 836.
The Linux OSL _OSI code is also changed.
acpi_osi_setup can't call acpi_install/remove_interface because ACPICA
is not initialized yet at this early time.
So we just save the osi string in acpi_osi_setup and will handle it
later in a new function acpi_osi_setup_late.
http://www.acpica.org/bugzilla/show_bug.cgi?id=836
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com
Signed-off-by: Len Brown <len.brown@intel.com>
The acpi_set_gpe() function is a little awkward, because it doesn't
really work as advertised in the "disable" case. Namely, if a GPE
has been enabled with acpi_enable_gpe() and triggered a notification
to occur, and if acpi_set_gpe() is used to disable it before
acpi_ev_asynch_enable_gpe() runs, the GPE will be immediately enabled
by the latter as though the acpi_set_gpe() had no effect.
Thus, since it's been possible to make all of its callers use
alternative operations to disable or enable GPEs, acpi_set_gpe() can
be dropped.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
After the previous patch that introduced acpi_gpe_wakeup() and
modified the ACPI suspend and wakeup code to use it, the third
argument of acpi_{enable|disable}_gpe() and the GPE wakeup
reference counter are not necessary any more. Remove them and
modify all of the users of acpi_{enable|disable}_gpe()
accordingly. Also drop GPE type constants that aren't used
any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses reference counters to avoid disabling GPEs too early in
case they have been enabled for many times. This is done separately
for runtime and for wakeup, but the wakeup GPE reference counter is
not really necessary, because GPEs are only enabled to wake up the
system at the hardware level by acpi_enter_sleep_state(). Thus it
only is necessary to set the corresponding bits in the wakeup enable
masks of these GPEs' registers right before the system enters a sleep
state. Moreover, the GPE wakeup enable bits can only be set when the
target sleep state of the system is known and they need to be cleared
immediately after wakeup regardless of how many wakeup devices are
associated with a given GPE.
On the basis of the above observations, introduce function
acpi_gpe_wakeup() to be used for setting or clearing the enable bit
corresponding to a given GPE in its enable register's enable_for_wake
mask. Modify the ACPI suspend and wakeup code the use
acpi_gpe_wakeup() instead of acpi_{enable|disable}_gpe() to set
and clear GPE enable bits in their registers' enable_for_wake masks
during system transitions to a sleep state and back to the working
state, respectively. [This will allow us to drop the third
argument of acpi_{enable|disable}_gpe() and simplify the GPE
handling code.]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses acpi_hw_write_gpe_enable_reg() to re-enable a GPE after
an event signaled by it has been handled. However, this function
writes the entire GPE enable mask to the GPE's enable register which
may not be correct. Namely, if one of the other GPEs in the same
register was previously enabled by acpi_enable_gpe() and subsequently
disabled using acpi_set_gpe(), acpi_hw_write_gpe_enable_reg() will
re-enable it along with the target GPE.
To fix this issue rework acpi_hw_write_gpe_enable_reg() so that it
calls acpi_hw_low_set_gpe() with a special action value,
ACPI_GPE_COND_ENABLE, that will make it only enable the GPE if the
corresponding bit in its register's enable_for_run mask is set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses acpi_ev_enable_gpe() for enabling GPEs at the low level,
which is incorrect, because this function only enables the GPE if the
corresponding bit in its enable register's enable_for_run mask is set.
This causes acpi_set_gpe() to work incorrectly if used for enabling
GPEs that were not previously enabled with acpi_enable_gpe(). As a
result, among other things, wakeup-only GPEs are never enabled by
acpi_enable_wakeup_device(), so the devices that use them are unable
to wake up the system.
To fix this issue remove acpi_ev_enable_gpe() and its counterpart
acpi_ev_disable_gpe() and replace acpi_hw_low_disable_gpe() with
acpi_hw_low_set_gpe() that will be used instead to manipulate GPE
enable bits at the low level. Make the users of acpi_ev_enable_gpe()
and acpi_ev_disable_gpe() call acpi_hw_low_set_gpe() instead and
make sure that GPE enable masks are only updated by acpi_enable_gpe()
and acpi_disable_gpe() when GPE reference counters change from 0
to 1 and from 1 to 0, respectively.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Simple rename of some parameters to standardize them.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We have ported Rafael's major GPE changes
(ACPI: Use GPE reference counting to support shared GPEs) into ACPICA code base.
But the port and Rafael's original patch have some differences, so we made
below patch to make linux GPE code consistent with ACPICA code base.
Most changes are about comments and coding styles.
Other noticeable changes are based on:
Rafael: Reduce code duplication related to GPE lookup
https://patchwork.kernel.org/patch/86237/
Rafael: Always use the same lock for GPE locking
https://patchwork.kernel.org/patch/90471/
A new field gpe_count in struct acpi_gpe_block_info to record the number
of individual GPEs in block.
Rename acpi_ev_save_method_info to acpi_ev_match_gpe_method.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Robert Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: replace acpi_integer by u64
ACPICA: Update version to 20100121.
ACPICA: Remove unused uint32_struct type
ACPICA: Disassembler: Remove obsolete "Integer64" field in parse object
ACPICA: Remove obsolete ACPI_INTEGER (acpi_integer) type
ACPICA: Predefined name repair: fix NULL package elements
ACPICA: AcpiGetDevices: Eliminate unnecessary _STA calls
ACPICA: Update all ACPICA copyrights and signons to 2010
ACPICA: Update for new gcc-4 warning options
ACPI GPEs may map to multiple devices. The current GPE interface
only provides a mechanism for enabling and disabling GPEs, making
it difficult to change the state of GPEs at runtime without extensive
cooperation between devices.
Add an API to allow devices to indicate whether or not they want
their device's GPE to be enabled for both runtime and wakeup events.
Remove the old GPE type handling entirely, which gets rid of various
quirks, like the implicit disabling with GPE type setting. This
requires a small amount of rework in order to ensure that non-wake
GPEs are enabled by default to preserve existing behaviour.
Based on patches from Matthew Garrett <mjg@redhat.com>.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This type is not used in ACPICA and thus removed.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This type was introduced as the code was migrated from ACPI 1.0
(with 32-bit AML integers) to ACPI 2.0 (with 64-bit integers). It
is now obsolete and this change removes it from the ACPICA code
base, replaced by u64. The original typedef has been retained
for now for compatibility with existing device driver code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add 2010 copyright to all module headers and signons, including
the Linux header. This affects virtually every file in the ACPICA
core subsystem, iASL compiler, and all utilities.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (119 commits)
ACPI: don't pass handle for fixed hardware notifications
ACPI: remove null pointer checks in deferred execution path
ACPI: simplify deferred execution path
acerhdf: additional BIOS versions
acerhdf: convert to dev_pm_ops
acerhdf: fix fan control for AOA150 model
thermal: add missing Kconfig dependency
acpi: switch /proc/acpi/{debug_layer,debug_level} to seq_file
hp-wmi: fix rfkill memory leak on unload
ACPI: remove unnecessary #ifdef CONFIG_DMI
ACPI: linux/acpi.h should not include linux/dmi.h
hwmon driver for ACPI 4.0 power meters
topstar-laptop: add new driver for hotkeys support on Topstar N01
thinkpad_acpi: fix rfkill memory leak on unload
thinkpad-acpi: report brightness events when required
thinkpad-acpi: don't poll by default any of the reserved hotkeys
thinkpad-acpi: Fix procfs hotkey reset command
thinkpad-acpi: deprecate hotkey_bios_mask
thinkpad-acpi: hotkey poll fixes
thinkpad-acpi: be more strict when detecting a ThinkPad
...
Handler was never invoked. Now invoked if/when host node is deleted.
Data object was not automatically deleted when host node was deleted.
Interface to handler had an unused parameter, removed it.
ACPICA BZ 778.
http://acpica.org/bugzilla/show_bug.cgi?id=778
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Adds support for IPMI which is similar to SMBus and uses a bi-directional data buffer.
ACPICA BZ 773.
http://acpica.org/bugzilla/show_bug.cgi?id=773
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Completed a major update for the acpi_get_object_info external interface.
Changes include:
- Support for variable, unlimited length HID, UID, and CID strings
- Support Processor objects the same as Devices (HID,UID,CID,ADR,STA, etc.)
- Call the _SxW power methods on behalf of a device object
- Determine if a device is a PCI root bridge
- Change the ACPI_BUFFER parameter to ACPI_DEVICE_INFO.
These changes will require an update to all callers of this interface.
See the ACPICA Programmer Reference for details.
Also, update all invocations of acpi_get_object_info interface
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed unnecessary masking. For the 64-bit macros, removed
the structure overlay. Fixes aliasing warnings seen with gcc 4+
compilers.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add and deploy constants for the PM status/enable/control
registers.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This type is the same as TYPE_A. Removed this and all related
instances. Renamed SLEEP_TYPE_A to simply SLEEP_TYPE.
ACPICA BZ 754.
http://www.acpica.org/bugzilla/show_bug.cgi?id=754
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
It is always "an" if there is a vowel _spoken_ (not written).
So it is:
"an hour" (spoken vowel)
but
"a uniform" (spoken 'j')
Signed-off-by: Frederik Schwarzer <schwarzerf@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
1) Update the register lengths for the PM1 event blocks. The
length must be divided by two in order to use these to access
the status registers.
2) Add run-time option to use default register lengths to override a
faulty FADT.
3) Add warning message if any of the X64 address structures contain a length
that does not match the legacy length earlier in the FADT.
4) Move all FADT warning messages into the ValidateFadt function.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Used to specify whether the OSL mutex interfaces should be used,
or binary semaphores instead.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi.h now includes only the "public" acpica headers. All other
acpica headers are "private" and should not be included by acpica
users. One new file, accommon.h is used to include the commonly
used private headers for acpica code generation. Future plans
are to move all private headers to a new subdirectory.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
New compiler is pickier than older versions.
Joerg Sonnenberger. From ACPICA BZ 732.
http://www.acpica.org/bugzilla/show_bug.cgi?id=732
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce a new flag showing whether the event has an event handler/method.
For all the GPEs and Fixed Events,
1. ACPI_EVENT_FLAG_HANDLE is cleared, it's an "invalid" ACPI event.
2. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_DISABLE are set,
it's "disabled".
3. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_ENABLE are set,
it's "enabled".
4. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_WAKE_ENABLE are set,
it's "wake_enabled".
Among other things, this prevents incorrect reporting of ACPI events
as being "invalid" when it's really just (temporarily) "disabled".
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed the ACPI_BITREG_WAKE_ENABLE definition and entry in the
global register table. This bit does not exist and is unused.
http://www.acpica.org/bugzilla/show_bug.cgi?id=442
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Also update the debugger so that the correct number of arguments is
passed to the method. Prevents a warning message from the debugger.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
