On OMAP4, MMC2 controller has eMMC which draws power from VAUX regulator
on TWL. Though the eMMC supports dual voltage[1.8v/3v] as per ocr register,
its VCC is fixed at 3V for operation. With this once the mmc core selects
the minimum voltage[1.8] supported based on the ocr value read from OCR register,
eMMC will not get detected. Thus the platform data for MMC2 is updated with ocr
mask and same will be communicated to core which will set the regulator to
always operate at 3V when ever turned ON.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In OMAP4, as per new PM programming model, the legacy registers
which were there in OMAP3 are all shifted by 0x100 while new one's
are added from offset 0 to 0x10.
For OMAP4, the register offset appending of 0x100 done in devices.c
currently, is moved to driver file.This change fits in for current
implementation as well as once the driver undergoes hwmod adaptation.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap4 es2 hsmmc has a updated soft reset logic.After the
reset is issued monitor a 0->1 transition first. The reset of
CMD or DATA lines is complete only after a 0->1->0 transition
of SRC or SRD bits.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If not all clocks have been defined in platform data, the driver will
cause a null pointer dereference when it is removed. This patch fixes
this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the commit f522886e20 a merge conflict
in the sdhci-s3c driver been fixed. However the fix used incorrect
spinlock operation - it caused a race with sdhci interrupt service. The
correct way to solve it is to use spin_lock_irqsave/irqrestore() calls.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently the kernel is screaming about slowpath at me for the
wp/cd callbacks. Switch to the _cansleep variants so as to silence
this.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The card may be always present on the board, and for these cases neither
a status callback nor a card detect GPIO is required, and card detection
polling can be disabled.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If an IRQ can be requested on the card detected GPIO, use it instead of
polling.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Barrier is deemed too heavy and will soon be replaced by FLUSH/FUA
requests. Deprecate barrier. All REQ_HARDBARRIERs are failed with
-EOPNOTSUPP and blk_queue_ordered() is replaced with simpler
blk_queue_flush().
blk_queue_flush() takes combinations of REQ_FLUSH and FUA. If a
device has write cache and can flush it, it should set REQ_FLUSH. If
the device can handle FUA writes, it should also set REQ_FUA.
All blk_queue_ordered() users are converted.
* ORDERED_DRAIN is mapped to 0 which is the default value.
* ORDERED_DRAIN_FLUSH is mapped to REQ_FLUSH.
* ORDERED_DRAIN_FLUSH_FUA is mapped to REQ_FLUSH | REQ_FUA.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Move the second if (reg & ...) test into the branch indicated by its
indentation. The test was previously always executed after the if
containing that branch, but it was always false unless the if branch was
taken.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Pavel Pisa <ppisa@pikron.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If suspend called when kmmcd is doing host->ops->disable, as kmmcd already
increased host->en_dis_recurs to 1, the mmc_host_enable in suspend
function will return directly without increase the nesting_cnt, which will
cause the followed register access carried out to the disabled host.
mmc_suspend_host will enable host itself. No need to enable host before
it. Also works on kmmcd will get flushed in mmc_suspend_host, enable host
after it will be safe. So make the mmc_host_enable after it.
[cjb: rebase against current Linus]
Signed-off-by: Ethan <ethan.too@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following error:
at91_mci.c: In function 'at91_mci_sg_to_dma':
at91_mci.c:236: error: implicit declaration of function 'kmap_atomic'
at91_mci.c:236: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
at91_mci.c:236: error: (Each undeclared identifier is reported only once
at91_mci.c:236: error: for each function it appears in.)
at91_mci.c:236: warning: assignment makes pointer from integer without a cast
at91_mci.c:252: error: implicit declaration of function 'kunmap_atomic'
at91_mci.c: In function 'at91_mci_post_dma_read':
at91_mci.c:302: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
at91_mci.c:302: warning: assignment makes pointer from integer without a cast
at91_mci.c:317: error: implicit declaration of function 'flush_kernel_dcache_page'
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes the following warning:
drivers/mmc/host/omap_hsmmc.c: In function 'omap_hsmmc_suspend':
drivers/mmc/host/omap_hsmmc.c:2275: warning: unused variable 'state'
Introduced by commit ID:
commit 1a13f8fa76
Author: Matt Fleming <matt@console-pimps.org>
Date: Wed May 26 14:42:08 2010 -0700
mmc: remove the "state" argument to mmc_suspend_host()
The unique usage of this var was removed there, and missed
removing the respective declaration aswell.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kunmap_atomic() takes the cookie, returned by the kmap_atomic() as its
argument and not the page address, used as an argument to kmap_atomic().
This patch fixes the compile error:
In file included from drivers/mmc/host/tmio_mmc.c:37:
drivers/mmc/host/tmio_mmc.h: In function 'tmio_mmc_kunmap_atomic':
drivers/mmc/host/tmio_mmc.h:192: error: negative width in bit-field '<anonymous>'
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Magnus Damm <damm@opensource.se>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously, it was possible for ack_mmc_irqs() to clear pending interrupt
bits in the CTL_STATUS register, even though the interrupt handler had not
been called. This was because of a race that existed when doing a
read-modify-write sequence on CTL_STATUS. After the read step in this
sequence, if an interrupt occurred (causing one of the bits in CTL_STATUS
to be set) the write step would inadvertently clear it.
Observed with the TMIO_STAT_RXRDY bit together with CMD53 on AR6002 and
BCM4318 SDIO cards in polled mode.
This patch eliminates this race by only writing to CTL_STATUS and clearing
the interrupts that were passed as an argument to ack_mmc_irqs()."
[matt@console-pimps.org: rewrote changelog]
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>"
Tested-by: Arnd Hannemann <arnd@arndnet.de>"
Acked-by: Ian Molton <ian@mnementh.co.uk>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The introduction of support for SD combo cards breaks the initialization
of all CSR SDIO chips. The GO_IDLE (CMD0) in mmc_sd_get_cid() causes CSR
chips to be reset (this is non-standard behavior).
When initializing an SDIO card check for a combo card by using the memory
present bit in the R4 response to IO_SEND_OP_COND (CMD5). This avoids the
call to mmc_sd_get_cid() on an SDIO-only card.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Acked-by: Michal Mirolaw <mirq-linux@rere.qmqm.pl>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Ux500 variant has a 32-word FIFO (TXFIFOEMPTY is asserted when it
has 2 left) and TXFIFOHALFEMPTY is repurposed as TXFIFOBURSTWRITEABLE,
with a burst being defined as 8-words. Likewise for RX.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On some platforms, the GPIO value from the gpio_cd pin doesn't need to
be inverted to get it active high. Add a cd_invert platform data
parameter and change existing platforms using GPIO for CD (only
Realview) to enable it.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's some merge problem between sdhic core and sdhci-s3c host. After
mutex is changed to spinlock. It needs to use use spin lock functions and
use the correct card detection function.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SDHCI controllers like s5pc110 don't have an HISPD bit in the HOSTCTL
register.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a build breakage introduced by commit 4c2ef25fe0 ("mmc: fix
all hangs related to mmc/sd card insert/removal during suspend/resume")
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-mmc@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/amba_pl022: Fix probe and remove hook section annotations.
spi/mpc5121: change annotations for probe and remove functions
spi/bitbang: reinitialize transfer parameters for every message
spi/spi-gpio: add support for controllers without MISO or MOSI pin
spi/bitbang: add support for SPI_MASTER_NO_{TX, RX} modes
SPI100k: Fix 8-bit and RX-only transfers
spi/mmc_spi: mmc_spi adaptations for SPI bus locking API
spi/mmc_spi: SPI bus locking API, using mutex
Fix trivial conflict in drivers/spi/mpc512x_psc_spi.c due to 'struct
of_device' => 'struct platform_device' rename and __init/__exit to
__devinit/__devexit fix.
* 'msm-mmc_sdcc' of git://codeaurora.org/quic/kernel/dwalker/linux-msm:
mmc: msm_sdcc: Rename config MMC_MSM7X00A to MMC_MSM
mmc: msm_sdcc: Compile the driver for msm7x30
mmc: msm: fix up build breakage on !PM
- Fix mmc_test_alloc_mem.
- Use nr_free_buffer_pages() instead of sysinfo.totalram to determine
total lowmem pages.
- Change variables containing memory sizes to unsigned long.
- Limit maximum test area size to 128MiB because that is the maximum MMC
high capacity erase size (the maxmium SD allocation unit size is just
4MiB)
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mmc_test provides tests aimed at testing SD/MMC hosts. This patch adds
performance tests.
It is advantageous to have performance tests in a kernel
module like mmc_test for the following reasons:
- transfer times can be measured very accurately
- arbitrarily large transfers are possible
- the effect of contiguous vs scattered pages
can be determined
The new tests are:
23. Best-case read performance
24. Best-case write performance
25. Best-case read performance into scattered pages
26. Best-case write performance from scattered pages
27. Single read performance by transfer size
28. Single write performance by transfer size
29. Single trim performance by transfer size
30. Consecutive read performance by transfer size
31. Consecutive write performance by transfer size
32. Consecutive trim performance by transfer size
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Secure discard is implemented by Secure Trim if the discard is unaligned
or Secure Erase otherwise.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Disable the data (busy) timeout for erases and set the MMC_CAP_ERASE
capability.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable MMC to service discard requests. In the case of SD and MMC cards
that do not support trim, discards become erases. In the case of cards
(MMC) that only allow erases in multiples of erase group size, round to
the nearest completely discarded erase group.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add auto CMD12 command support for eSDHC driver. This is needed by P4080
and P1022 for block read/write. Manual asynchronous CMD12 abort operation
causes protocol violations on these silicons.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for regulator API to sdhci core driver.
Regulators can be used to disable power in suspended state to reduce
dissipated energy.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some Samsung SoCs not all SDHCI controllers have card detect (CD) line.
For some embedded designs it is not even needed, because ususally the
device (like SDIO flash memory or wifi controller) is permanently wired to
the controller. There are also systems which have a card detect line
connected to some of the external interrupt lines or the presence of the
card depends on some other actions (like enabling a power regulator).
This patch adds support for all these cases. The following card detection
methods are possible:
1. internal sdhci host card detect line
2. external event
3. external gpio interrupt
4. no card detect line, controller will poll for the card
5. no card detect line, card is permanently wired to the controller
(once detected host won't poll it any more)
By default, all existing code would use method #1, what is compatible with
the previous version of the driver.
In case of external event, two callbacks must be provided in platdata:
ext_cd_init and ext_cd_cleanup. Both of them get a callback to a function
that notifies the s3c-sdhci host contoller as their argument. That
callback function should be called from the even dispatcher to let host
notice the card insertion/removal.
In case of external gpio interrupt, a gpio pin number must be provided in
platdata (ext_cd_gpio parameter), as well as the information about the
polarity of that gpio pin (ext_cd_gpio_invert). By default
(ext_cd_gpio_invert == 0) gpio value 0 means 'card has been removed', but
this can be changed to 'card has been removed' when ext_cd_gpio_invert ==
1.
This patch adds all required changes to sdhci-s3c driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch enables SDHCI_QUIRK_NO_HISPD_BIT on Samsung SDHCI driver. This
solves detection problems with some external SD cards. This change has
been tested on S5PC100 and S5PC110. It has no inpact on driver speed.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
S3C SDHCI host controller can change the source for generating mmc clock.
By default host bus clock is used, what causes some problems on machines
with 133MHz bus, because the SDHCI divider cannot be as high get proper
clock value for identification mode. This is not a problem for the
controller, because it can generate lower frequencies from other clock
sources. This patch changes sdhci driver to use get_min_clock() call if
it has been provided.
This fixes the flood of the following warnings on Samsung S5PV210 SoCs:
mmc0: Minimum clock frequency too high for identification mode
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Samsung's SDMMC hosts the timeout clock is derivied from the SD Clock
which is set dynamically. So checked SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
quirk and removed 'sdhci_s3c_get_timeout_clk' callback which doesn't need
any more.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If other informative interrupts are enabled for the DMA channel used by
hsmmc, those are incorrectly treated as block completion. This patch lets
only the block completion interrupt to be processed.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_MMC_MSM7X00A_RESUME_IN_WQ and CONFIG_MMC_EMBEDDED_SDIO don't exist
in Kconfig and is never defined anywhere else, therefore removing all
references for it from the source code.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@codeaurora.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This will allow us to set up special cards in machine drivers just after
they are detected by MMC core.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Kalle Valo <kvalo@adurom.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are some chips (like TI WL12xx series) that can be interfaced over
SDIO but don't support the SDIO specification, meaning that they are
missing CIA (Common I/O Area) with all it's registers. Current Linux SDIO
implementation relies on those registers to identify and configure the
card, so non-standard cards can not function and cause lots of warnings
from the core when it reads invalid data from non-existent registers.
After this patch, init_card() host callback can now set new quirk
MMC_QUIRK_NONSTD_SDIO, which means that SDIO core should not try to access
any standard SDIO registers and rely on init_card() to fill all SDIO
structures instead. As those cards are usually embedded chips, all the
required information can be obtained from machine board files by the host
driver when it's called through init_card() callback.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Kalle Valo <kvalo@adurom.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's nothing special, just SoC-specific ops and quirks.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Richard R?jfors <richard.rojfors@pelagicore.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to build system limitations, intermediate and final objects can't have
the same names. And as we're going to start building SoC-specific
objects, let's rename the module to sdhci-platform, into which we'll link
sdhci-pltfm and SoC-specifc objects.
There should be no issue in renaming as the driver uses modalias
mechanism.
This is exactly the same approach as in sdhci-of driver.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Richard R?jfors <richard.rojfors@pelagicore.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes want to place SoC-specific parts alongside with the generic
driver, and to do so, we have to switch the driver over to the module
device table matching.
Note that drivers/mmc/host/sdhci-pltfm.h is so far empty, but it'll hold
SoC-specific driver data handlers soon.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Richard R?jfors <richard.rojfors@pelagicore.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
