This patch declares the internal struct and functions as static to provide
more security.
Signed-off-by: Xiaoyan Zhang <xiaoyan.zhang@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Kent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
The Physical Presence Interface enables the OS and the BIOS to cooperate and
provides a simple and straightforward platform user experience for
administering the TPM without sacrificing security.
V2: separate the patch out in a separate source file,
add #ifdef CONFIG_ACPI so it compiles out on ppc,
use standard error instead of ACPI error as return code of show/store fns.
V3: move #ifdef CONFIG_ACPI from .c file to .h file.
V4: move tpm_ppi code from tpm module to tpm_bios module.
V5: modify sys_add_ppi() so that ppi_attr_grp doesn't need to be exported
Signed-off-by: Xiaoyan Zhang <xiaoyan.zhang@intel.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
In drivers/char/tpm/tpm_acpi.c::read_log() we call
acpi_os_map_memory(). That call may fail for a number of reasons
(invalid address, out of memory etc). If the call fails it returns
NULL and we just pass that to memcpy() unconditionally, which will go
bad when it tries to dereference the pointer.
Unfortunately we just get NULL back, so we can't really tell the user
exactely what went wrong, but we can at least avoid crashing and
return an error (-EIO seemed more generic and more suitable here than
-ENOMEM or something else, so I picked that).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch retrieves the event log data from the device tree
during file open. The event log data will then displayed through
securityfs.
Signed-off-by: Ashley Lai <adlai@us.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch adds a new device driver to support IBM virtual TPM
(vTPM) for PPC64. IBM vTPM is supported through the adjunct
partition with firmware release 740 or higher. With vTPM
support, each lpar is able to have its own vTPM without the
physical TPM hardware.
This driver provides TPM functionalities by communicating with
the vTPM adjunct partition through Hypervisor calls (Hcalls)
and Command/Response Queue (CRQ) commands.
Signed-off-by: Ashley Lai <adlai@us.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
The tpm_tis driver doesn't use tpm_tis_resume except when PM is
configured and doesn't make use of tpm_tis_reenable_interrupts except
when PM or PNP is configured.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Moved the atomic_set of the data_pending variable until after the
tpm_read has completed processing. The existing code had a window of
time where a second write to the driver could clobber the tpm command
buffer.
Also fixed an issue where if close was called on the tpm device before a
read completed, the tpm command buffer would be returned to the OS,
which could contain sensitive information.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Move the tpm_get_random api from the trusted keys code into the TPM
device driver itself so that other callers can make use of it. Also,
change the api slightly so that the number of bytes read is returned in
the call, since the TPM command can potentially return fewer bytes than
requested.
Acked-by: David Safford <safford@linux.vnet.ibm.com>
Reviewed-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Break ACPI-specific pieces of the event log handling into their own file
and create tpm_eventlog.[ch] to store common event log handling code.
This will be required to integrate future event log sources on platforms
without ACPI tables.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch adds a driver to support Infineon's SLB 9635 TT 1.2 Soft I2C TPMs
which follow the TGC TIS 1.2 TPM specification[1] and Infineon's I2C Protocol
Stack Specification 0.20.
The I2C Protocol Stack Specification is a simple adaption of the LPC TIS
Protocol to the I2C Bus.
The I2C TPMs can be used when LPC Bus is not available (i.e. non x86
architectures like ARM).
The driver is based on the tpm_tis.c driver by Leendert van Dorn and Kyleen
Hall and has quite similar functionality.
Tested on Nvidia ARM Tegra2 Development Platform and Beagleboard (ARM OMAP)
Tested with the Trousers[2] TSS API Testsuite v 0.3 [3]
Compile-tested on x86 (32/64-bit)
Updates since version 2.1.4:
- included "Lock the I2C adapter for a sequence of requests", by Bryan Freed
- use __i2c_transfer instead of own implementation of unlocked i2c_transfer
- use struct dev_pm_ops for power management via SIMPLE_DEV_PM_OPS
Updates since version 2.1.3:
- use proper probing mechanism
* either add the tpm using I2C_BOARD_INFO to your board file or probe it
* during runtime e.g on BeagleBoard using :
* "echo tpm_i2c_infineon 0x20 > /sys/bus/i2c/devices/i2c-2/new_device"
- fix possible endless loop if hardware misbehaves
- improved return codes
- consistent spelling i2c/tpm -> I2C/TPM
- remove hardcoded sleep values and msleep usage
- removed debug statements
- added check for I2C functionality
- renaming to tpm_i2c_infineon
Updates since version 2.1.2:
- added sysfs entries for duration and timeouts
- updated to new tpm_do_selftest
Updates since version 2.1.0:
- improved error handling
- implemented workarounds needed by the tpm
- fixed typos
References:
[1]
http://www.trustedcomputinggroup.org/resources/pc_client_work_group_pc_client_
specific_tpm_interface_specification_tis_version_12/
[2] http://trousers.sourceforge.net/
[3]
http://sourceforge.net/projects/trousers/files/TSS%20API%20test%20suite/0.3/
Reviewed-by: Andi Shyti <andi.shyti@gmail.com>
Acked-by: Marcel Selhorst <tpmdd@selhorst.net>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Bryan Freed <bfreed@chromium.org>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
According to a compiler warning, the tpm_tis_resume() function is not
used for CONFIG_PM_SLEEP unset, so add a #ifdef to prevent it from
being built in that case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Pull security subsystem updates from James Morris:
"Nothing groundbreaking for this kernel, just cleanups and fixes, and a
couple of Smack enhancements."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (21 commits)
Smack: Maintainer Record
Smack: don't show empty rules when /smack/load or /smack/load2 is read
Smack: user access check bounds
Smack: onlycap limits on CAP_MAC_ADMIN
Smack: fix smack_new_inode bogosities
ima: audit is compiled only when enabled
ima: ima_initialized is set only if successful
ima: add policy for pseudo fs
ima: remove unused cleanup functions
ima: free securityfs violations file
ima: use full pathnames in measurement list
security: Fix nommu build.
samples: seccomp: add .gitignore for untracked executables
tpm: check the chip reference before using it
TPM: fix memleak when register hardware fails
TPM: chip disabled state erronously being reported as error
MAINTAINERS: TPM maintainers' contacts update
Merge branches 'next-queue' and 'next' into next
Remove unused code from MPI library
Revert "crypto: GnuPG based MPI lib - additional sources (part 4)"
...
Make the tpm_nsc driver define its PM callbacks through
a struct dev_pm_ops object rather than by using legacy PM hooks
in struct platform_driver.
This allows the driver to use tpm_pm_suspend() and tpm_pm_resume()
as its PM callbacks directly, without defining its own PM callback
routines.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Make the tpm_tis driver define its PM callbacks through
a struct dev_pm_ops object rather than by using legacy PM hooks
in struct platform_driver.
This allows the driver to use tpm_pm_suspend() as its suspend
callback directly, without defining its own suspend callback
routine.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Make the tpm_atmel driver define its PM callbacks through
a struct dev_pm_ops object rather than by using legacy PM hooks
in struct platform_driver.
This allows the driver to use tpm_pm_suspend() and tpm_pm_resume()
as its PM callbacks directly, without defining its own PM callback
routines.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If a driver calls tpm_dev_vendor_release for a device already released
then the driver will oops.
Signed-off-by: Andi Shyti <andi.shyti@gmail.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
tpm_do_selftest() attempts to read a PCR in order to
decide if one can rely on the TPM being used or not.
The function that's used by __tpm_pcr_read() does not
expect the TPM to be disabled or deactivated, and if so,
reports an error.
It's fine if the TPM returns this error when trying to
use it for the first time after a power cycle, but it's
definitely not if it already returned success for a
previous attempt to read one of its PCRs.
The tpm_do_selftest() was modified so that the driver only
reports this return code as an error when it really is.
Reported-and-tested-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Usual contact update, Debora Velarde role resign, and the new
co-maintainer inclusion, Kent Yoder. He's accepted to contribute
more actively to this driver's maintainership given the current
maintainer's slight career change that will affect his contribution
time.
[Replacing Debora Velarde by Kent Yoder]
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Pull security subsystem updates for 3.4 from James Morris:
"The main addition here is the new Yama security module from Kees Cook,
which was discussed at the Linux Security Summit last year. Its
purpose is to collect miscellaneous DAC security enhancements in one
place. This also marks a departure in policy for LSM modules, which
were previously limited to being standalone access control systems.
Chromium OS is using Yama, and I believe there are plans for Ubuntu,
at least.
This patchset also includes maintenance updates for AppArmor, TOMOYO
and others."
Fix trivial conflict in <net/sock.h> due to the jumo_label->static_key
rename.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (38 commits)
AppArmor: Fix location of const qualifier on generated string tables
TOMOYO: Return error if fails to delete a domain
AppArmor: add const qualifiers to string arrays
AppArmor: Add ability to load extended policy
TOMOYO: Return appropriate value to poll().
AppArmor: Move path failure information into aa_get_name and rename
AppArmor: Update dfa matching routines.
AppArmor: Minor cleanup of d_namespace_path to consolidate error handling
AppArmor: Retrieve the dentry_path for error reporting when path lookup fails
AppArmor: Add const qualifiers to generated string tables
AppArmor: Fix oops in policy unpack auditing
AppArmor: Fix error returned when a path lookup is disconnected
KEYS: testing wrong bit for KEY_FLAG_REVOKED
TOMOYO: Fix mount flags checking order.
security: fix ima kconfig warning
AppArmor: Fix the error case for chroot relative path name lookup
AppArmor: fix mapping of META_READ to audit and quiet flags
AppArmor: Fix underflow in xindex calculation
AppArmor: Fix dropping of allowed operations that are force audited
AppArmor: Add mising end of structure test to caps unpacking
...
cleanup_tis() -> tpm_remove_hardware() -> syncrhonize_rcu() is being
called in an atomic context (tis_lock spinlock held), which is not
allowed. Convert tis_lock to mutex.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Commit 3321c07ae5 correctly clears the TPM
buffer if the user specified read length is >= the TPM buffer length. However,
if the user specified read length is < the TPM buffer length, then part of the
TPM buffer is left uncleared.
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Marcel Selhorst <m.selhorst@sirrix.com>
Cc: tpmdd-devel@lists.sourceforge.net
Cc: stable@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Commit 90ab5ee941 changed the
itpm module parameter from int to bool. Some other changes
need to be done to clean up after this change.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Detect iTPMs through the vendor ID on the hardware interface and only
probe the device if the manufacturer is found to be Intel. This
obsoletes a previously added delay necessary for some TPMs but not iTPMs.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch fixes an (ACPI S3) suspend regression introduced in commit
68d6e6713f ("tpm: Introduce function to poll for result of self test")
and occurring with an Infineon TPM and tpm_tis and tpm_infineon drivers
active.
The suspend problem occurred if the TPM was disabled and/or deactivated
and therefore the TPM_PCRRead checking the result of the (asynchronous)
self test returned an error code which then caused the tpm_tis driver to
become inactive and this then seemed to have negatively influenced the
suspend support by the tpm_infineon driver... Besides that the tpm_tis
drive may stay active even if the TPM is disabled and/or deactivated.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It's incorrect to assume that buffers returned by the TPM
10 bytes long are always error reports. This patches
parses the error field in its header instead. The error report
is now being printed using dev_err() instead of dev_dbg(), making
it easier for users to provide more detailed bug reports.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
A previous commit removed its PNP dependency, that in fact wasn't
necessary, but also allowed it be built for other architectures not
supported by it. This then caused kernel oops on PPC based machines.
I'm placing a x86 dependency back correctly.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Moved wait_for_stat to tpm.c so that other drivers can use it.
Also renamed it to avoid future namespace conflicts.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Moved from using tpm_tis_status() to the vendor specific
one in wait_for_stat(). This way other TPM drivers can use it
instead of reimplementing another.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch adds a delay after aborting a command. Some TPMs need
this and will not process the subsequent command correctly otherwise.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Check the return code from getting the TPM's timeouts and durations
and reject the driver if they could not be read.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This patch introduces a function that runs the TPM_ContinueSelfTest()
function and then polls the TPM to check whether it finished the selftest
and can receive new commands.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
* 'next' of git://selinuxproject.org/~jmorris/linux-security: (95 commits)
TOMOYO: Fix incomplete read after seek.
Smack: allow to access /smack/access as normal user
TOMOYO: Fix unused kernel config option.
Smack: fix: invalid length set for the result of /smack/access
Smack: compilation fix
Smack: fix for /smack/access output, use string instead of byte
Smack: domain transition protections (v3)
Smack: Provide information for UDS getsockopt(SO_PEERCRED)
Smack: Clean up comments
Smack: Repair processing of fcntl
Smack: Rule list lookup performance
Smack: check permissions from user space (v2)
TOMOYO: Fix quota and garbage collector.
TOMOYO: Remove redundant tasklist_lock.
TOMOYO: Fix domain transition failure warning.
TOMOYO: Remove tomoyo_policy_memory_lock spinlock.
TOMOYO: Simplify garbage collector.
TOMOYO: Fix make namespacecheck warnings.
target: check hex2bin result
encrypted-keys: check hex2bin result
...
Since the buffer might contain security related data it might be a good idea to
zero the buffer after we have copied it to userspace.
This got assigned CVE-2011-1162.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: James Morris <jmorris@namei.org>
This patch changes the call of tpm_transmit by supplying the size of the
userspace buffer instead of TPM_BUFSIZE.
This got assigned CVE-2011-1161.
[The first hunk didn't make sense given one could expect
way less data than TPM_BUFSIZE, so added tpm_transmit boundary
check over bufsiz instead
The last parameter of tpm_transmit() reflects the amount
of data expected from the device, and not the buffer size
being supplied to it. It isn't ideal to parse it directly,
so we just set it to the maximum the input buffer can handle
and let the userspace API to do such job.]
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: James Morris <jmorris@namei.org>
platform_device_unregister() will release all resources
and remove it from the subsystem, then drop reference count by
calling platform_device_put().
We should not call kfree(pdev) after platform_device_unregister(pdev).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
On m68k, I get:
drivers/char/tpm/tpm_atmel.h: In function ‘atmel_get_base_addr’:
drivers/char/tpm/tpm_atmel.h:129: error: implicit declaration of function ‘ioport_map’
drivers/char/tpm/tpm_atmel.h:129: warning: return makes pointer from integer without a cast
The code in tpm_atmel.h supports PPC64 (using the device tree and ioremap())
and "anything else" (using ioport_map()). However, ioportmap() is only
available on platforms that set HAS_IOPORT.
Although PC64 seems to have HAS_IOPORT, a "depends on HAS_IOPORT" should work,
but I think it's better to expose the special PPC64 handling explicit using
"depends on PPC64 || HAS_IOPORT".
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Suppress the output in the 'durations' sysfs entry if they were not read
during driver initialization. This is similar to other sysfs entries
that return nothing if for some reason sending the commands to the TPM
fails.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Fix tpm_tis.c build when CONFIG_ACPI is not enabled by providing a stub
function. Fixes many build errors/warnings:
drivers/char/tpm/tpm_tis.c:89: error: dereferencing pointer to incomplete type
drivers/char/tpm/tpm_tis.c:89: warning: type defaults to 'int' in declaration of 'type name'
drivers/char/tpm/tpm_tis.c:89: error: request for member 'list' in something not a structure or union
...
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Leendert van Doorn <leendert@watson.ibm.com>
Cc: James Morris <jmorris@namei.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves the tpm_tis_reenable_interrupts function out of the
CONFIG_PNP-surrounded #define block. This solves a compilation error in
case CONFIG_PNP is not defined.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Morris <jmorris@namei.org>
The is_itpm() function is only accessed from a block surrounded by
#ifdef CONFIG_PNP. Therefore, also surround it with #ifdef CONFIG_PNP
and remove the #else branch causing the warning.
http://lxr.linux.no/#linux+v2.6.39/drivers/char/tpm/tpm_tis.c#L622
v2:
- fixes a previous typo
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Morris <jmorris@namei.org>
This patch introduces a function for automatic probing for the Intel iTPM
STS_DATA_EXPECT flaw.
The patch splits the current tpm_tis_send function into 2 parts where the 1st
part is now called tpm_tis_send_data() and merely sends the data to the TPM.
This function is then used for probing. The new tpm_tis_send function now
first calls tpm_tis_send_data and if that succeeds has the TPM process the
command and waits until the response is there.
The probing for the Intel iTPM is only invoked if the user has not passed
itpm=1 as parameter for the module *or* if such a TPM was detected via ACPI.
Previously it was necessary to pass itpm=1 when also passing force=1 to the
module when doing a 'modprobe'. This function is more general than the ACPI
test function and the function relying on ACPI could probably be removed.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch fixes several aspects of the probing for interrupts.
This patch reads the TPM's timeouts before probing for the interrupts. The
tpm_get_timeouts() function is invoked in polling mode and gets the proper
timeouts from the TPM so that we don't need to fall back to 2 minutes timeouts
for short duration commands while the interrupt probing is happening.
This patch introduces a variable probed_irq into the vendor structure that gets
the irq number if an interrupt is received while the the tpm_gen_interrupt()
function is run in polling mode during interrupt probing. Previously some
parts of tpm_gen_interrupt() were run in polling mode, then the irq variable
was set in the interrupt handler when an interrupt was received and execution
of tpm_gen_interrupt() ended up switching over to interrupt mode.
tpm_gen_interrupt() execution ended up on an event queue where it eventually
timed out since the probing handler doesn't wake any queues.
Before calling into free_irq() clear all interrupt flags that may have
been set by the TPM. The reason is that free_irq() will call into the probing
interrupt handler and may otherwise fool us into thinking that a real interrupt
happened (because we see the flags as being set) while the TPM's interrupt line
is not even connected to anything on the motherboard. This solves a problem
on one machine I did testing on (Thinkpad T60).
If a TPM claims to use a specifc interrupt, the probing is done as well
to verify that the interrupt is actually working. If a TPM indicates
that it does not use a specific interrupt (returns '0'), probe all interrupts
from 3 to 15.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch delays the (ACPI S3) suspend while the TPM is busy processing a
command and the TPM TIS driver is run in interrupt mode. This is the same
behavior as we already have it for the TPM TIS driver in polling mode.
Reasoning: Some of the TPM's commands advance the internal state of the TPM.
An example would be the extending of one of its PCR registers. Upper layers,
such as IMA or TSS (TrouSerS), would certainly want to be sure that the
command succeeded rather than getting an error code (-62 = -ETIME) that may
not give a conclusive answer as for what reason the command failed. Reissuing
such a command would put the TPM into the wrong state, so waiting for it to
finish is really the only option.
The downside is that some commands (key creation) can take a long time and
actually prevent the machine from entering S3 at all before the 20 second
timeout of the power management subsystem arrives.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch makes sure that if the TPM TIS interface is run in interrupt mode
(rather than polling mode) that all interrupts are enabled in the TPM's
interrupt enable register after a resume from ACPI S3 suspend. The registers
may either have been cleared by the TPM loosing its state during device sleep
or by the BIOS leaving the TPM in polling mode (after sending a command to
the TPM for starting it up again)
You may want to check if your TPM runs with interrupts by doing
cat /proc/interrupts | grep -i tpm
and see whether there is an entry or otherwise for it to use interrupts:
modprobe tpm_tis interrupts=1 [add 'itpm=1' for Intel TPM ]
v2:
- the patch was adapted to work with the pnp and platform driver
implementations in tpm_tis.c
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch fixes the TPM's pubek sysfs entry that is accessible as long
as the TPM doesn't have an owner. It was necessary to shift the access to the
data by -10 -- the first byte immediately follows the 10 byte header. The
line
data = tpm_cmd.params.readpubek_out_buffer;
sets it at the offset '10' in the packet, so we can read the data array
starting at offset '0'.
Before:
Algorithm: 00 0C 00 00
Encscheme: 08 00
Sigscheme: 00 00
Parameters: 00 00 00 00 01 00 AC E2 5E 3C A0 78
Modulus length: -563306801
Modulus:
28 21 08 0F 82 CD F2 B1 E7 49 F7 74 70 BE 59 8C
43 78 B1 24 EA 52 E2 FE 52 5C 3A 12 3B DC 61 71
[...]
After:
Algorithm: 00 00 00 01
Encscheme: 00 03
Sigscheme: 00 01
Parameters: 00 00 08 00 00 00 00 02 00 00 00 00
Modulus length: 256
Modulus:
AC E2 5E 3C A0 78 DE 6C 9E CF 28 21 08 0F 82 CD
F2 B1 E7 49 F7 74 70 BE 59 8C 43 78 B1 24 EA 52
[...]
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Display the TPM's interface timeouts in a 'timeouts' sysfs entry. Display
the entries as having been adjusted when they were scaled due to their values
being reported in milliseconds rather than microseconds.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Adjust the interface timeouts if they are found to be too small, i.e., if
they are returned in milliseconds rather than microseconds as we heared
from Infineon that some (old) Infineon TPMs do.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
The TPM driver currently discards the interface timeout values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 4 interface timeout indicators of type u32.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Display the TPM's command timeouts in a 'durations' sysfs entry. Display
the entries as having been adjusted when they were scaled due to their values
being reported in milliseconds rather than microseconds.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Adjust the durations if they are found to be too small, i.e., if they are
returned in milliseconds rather than microseconds as some Infineon TPMs are
reported to do.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
The TPM driver currently discards the durations values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 3 timeout indicators of type u32.
v4:
- sysfs entry 'durations' is now a patch of its own
- the work-around for TPMs reporting durations in milliseconds is now in a
patch of its own
v3:
- sysfs entry now called 'durations' to resemble TPM-speak (previously
was called 'timeouts')
v2:
- adjusting all timeouts for TPM devices reporting timeouts in msec rather
than usec
- also displaying in sysfs whether the timeouts are 'original' or 'adjusted'
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch fixes information leakage to the userspace by initializing
the data buffer to zero.
Reported-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
[ Also removed the silly "* sizeof(u8)". If that isn't 1, we have way
deeper problems than a simple multiplication can fix. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit c4ff4b829e.
Ted Ts'o reports:
"TPM is working for me so I can log into employer's network in 2.6.37.
It broke when I tried 2.6.38-rc6, with the following relevant lines
from my dmesg:
[ 11.081627] tpm_tis 00:0b: 1.2 TPM (device-id 0x0, rev-id 78)
[ 25.734114] tpm_tis 00:0b: Operation Timed out
[ 78.040949] tpm_tis 00:0b: Operation Timed out
This caused me to get suspicious, especially since the _other_ TPM
commit in 2.6.38 had already been reverted, so I tried reverting
commit c4ff4b829e: "TPM: Long default timeout fix". With this commit
reverted, my TPM on my Lenovo T410 is once again working."
Requested-and-tested-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 9b29050f8f.
It has caused hibernate regressions, for example Juri Sladby's report:
"I'm unable to hibernate 2.6.37.1 unless I rmmod tpm_tis:
[10974.074587] Suspending console(s) (use no_console_suspend to debug)
[10974.103073] tpm_tis 00:0c: Operation Timed out
[10974.103089] legacy_suspend(): pnp_bus_suspend+0x0/0xa0 returns -62
[10974.103095] PM: Device 00:0c failed to freeze: error -62"
and Rafael points out that some of the new conditionals in that commit
seem to make no sense. This commit needs more work and testing, let's
revert it for now.
Reported-by: Norbert Preining <preining@logic.at>
Reported-and-requested-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Stefan Berger <stefanb@linux.vnet.ibm.com>
Cc: Guillaume Chazarain <guichaz@gmail.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current TPM TIS driver in git discards the timeout values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 3 timeout indicators of type u32.
I am also adding a sysfs entry 'timeouts' showing the timeouts that are
being used.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
commit 3f0d3d016d adds a check for
PNP device id to the common tpm_tis_init() function, which in some
cases (force=1) will be called without the device being a member of
a pnp_dev. Oopsing and panics ensue.
Move the test up to before the call to tpm_tis_init(), since it
just modifies a global variable anyway.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
If duration variable value is 0 at this point, it's because
chip->vendor.duration wasn't filled by tpm_get_timeouts() yet.
This patch sets then the lowest timeout just to give enough
time for tpm_get_timeouts() to further succeed.
This fix avoids long boot times in case another entity attempts
to send commands to the TPM when the TPM isn't accessible.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Conflicts:
security/smack/smack_lsm.c
Verified and added fix by Stephen Rothwell <sfr@canb.auug.org.au>
Ok'd by Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: James Morris <jmorris@namei.org>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
Some Lenovos have TPMs that require a quirk to function correctly. This can
be autodetected by checking whether the device has a _HID of INTC0102. This
is an invalid PNPid, and as such is discarded by the pnp layer - however
it's still present in the ACPI code, so we can pull it out that way. This
means that the quirk won't be automatically applied on non-ACPI systems,
but without ACPI we don't have any way to identify the chip anyway so I
don't think that's a great concern.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: James Morris <jmorris@namei.org>
Add internal kernel tpm_send() command used to seal/unseal keys.
Changelog:
- replaced module_put in tpm_send() with new tpm_chip_put() wrapper
(suggested by David Howells)
- Make tpm_send() cmd argument a 'void *' (suggested by David Howells)
Signed-off-by: David Safford <safford@watson.ibm.com>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
For readability, define a tpm_chip_put() wrapper to call module_put().
Replace existing module_put() calls with the wrapper.
(Change based on trusted/encrypted patchset review by David Howells.)
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: David Safford <safford@watson.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
Fix the following warning:
drivers/char/tpm/tpm.c:1085: warning: `tpm_suspend_setup' defined but not used
and make the workaround operable in case when TPM is compiled as a module.
As a side-effect the option will be called tpm.suspend_pcr.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: David Safford <safford@watson.ibm.com>
Cc: James Morris <jmorris@namei.org>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix subsequent suspends by issuing tpm_continue_selftest during resume.
Otherwise, the tpm chip seems to be not fully initialized and will reject
the save state command during suspend, thus preventing the whole system
to suspend.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16256
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: James Morris <jmorris@namei.org>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Cc: David Safford <safford@watson.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
This patch adds a missing element of the ReadPubEK command output,
that prevents future overflow of this buffer when copying the
TPM output result into it.
Prevents a kernel panic in case the user tries to read the
pubek from sysfs.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
This patch pushes the ACPI dependency into the device driver code
itself. Now, even without ACPI/PNP enabled, the device can be registered
using the TIS specified memory space. This will however result in the
lack of access to the BIOS event log, being the only implication of such
ACPI removal.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
This reverts commit b89e66e1e3.
> > When CONFIG_PM is not set:
> >
> > drivers/built-in.o: In function `acpi_init':
> > bus.c:(.init.text+0x2d84): undefined reference to `pm_flags'
> > bus.c:(.init.text+0x2d91): undefined reference to `pm_flags'
>
> CONFIG_ACPI depends on CONFIG_PM,
> so acpi/bus.c should not be compiled for CONFIG_PM=n
>
> Hmm, is is somebody doing something strange, like "select ACPI"
> without guaranteeing that all of ACPI's dependencies are satisfied?
Signed-off-by: James Morris <jmorris@namei.org>
This patch pushes the ACPI dependency into the device driver code
itself. Now, even without ACPI/PNP enabled, the device can be registered
using the TIS specified memory space. This will however result in the
lack of access to the bios event log, being the only implication of such
ACPI removal.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Add a workaround for TPM's which fail to flush last written
PCR values in a TPM_SaveState, in preparation for suspend.
Signed-off-by: David Safford <safford@watson.ibm.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
When suspending, tpm_infineon calls the generic suspend function of the
TPM framework. However, the TPM framework does not return and the system
hangs upon suspend. When sending the necessary command "TPM_SaveState"
directly within the driver, suspending and resuming works fine.
Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: <stable@kernel.org> [2.6.32.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tpm_tis driver already has a list of supported pnp_device_ids.
This patch simply exports that list as a MODULE_DEVICE_TABLE() so that
the module autoloader will discover and load the module at boottime.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
Some newer Lenovo models are shipped with a TPM that doesn't seem to set the TPM_STS_DATA_EXPECT status bit
when sending it a burst of data, so the code understands it as a failure and doesn't proceed sending the chip
the intended data. In this patch we bypass this bit check in case the itpm module parameter was set.
This patch is based on Andy Isaacson's one:
http://marc.info/?l=linux-kernel&m=124650185023495&w=2
It was heavily discussed how should we deal with identifying the chip in kernel space, but the required
patch to do so was NACK'd:
http://marc.info/?l=linux-kernel&m=124650186423711&w=2
This way we let the user choose using this workaround or not based on his
observations on this code behavior when trying to use the TPM.
Fixed a checkpatch issue present on the previous patch, thanks to Daniel Walker.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: Eric Paris <eparis@redhat.com>
Tested-by: Seiji Munetoh <seiji.munetoh@gmail.com>
Signed-off-by: James Morris <jmorris@namei.org>
The previously sent patch:
http://marc.info/?l=tpmdd-devel&m=125208945007834&w=2
Had its first hunk cropped when merged, submitting only this first hunk
again.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Cc: Marcel Selhorst <m.selhorst@sirrix.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: Mimi Zohar <zohar@us.ibm.com>
Tested-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
The TPM Working Group requested this communication buffer increase given that a
particular TPM vendor can support a TPM_SHA1Start command input bigger than the
current size.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
SELinux: do not destroy the avc_cache_nodep
KEYS: Have the garbage collector set its timer for live expired keys
tpm-fixup-pcrs-sysfs-file-update
creds_are_invalid() needs to be exported for use by modules:
include/linux/cred.h: fix build
Fix trivial BUILD_BUG_ON-induced conflicts in drivers/char/tpm/tpm.c
gcc permitting variable length arrays makes the current construct used for
BUILD_BUG_ON() useless, as that doesn't produce any diagnostic if the
controlling expression isn't really constant. Instead, this patch makes
it so that a bit field gets used here. Consequently, those uses where the
condition isn't really constant now also need fixing.
Note that in the gfp.h, kmemcheck.h, and virtio_config.h cases
MAYBE_BUILD_BUG_ON() really just serves documentation purposes - even if
the expression is compile time constant (__builtin_constant_p() yields
true), the array is still deemed of variable length by gcc, and hence the
whole expression doesn't have the intended effect.
[akpm@linux-foundation.org: make arch/sparc/include/asm/vio.h compile]
[akpm@linux-foundation.org: more nonsensical assertions in tpm.c..]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Mimi Zohar <zohar@us.ibm.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make all seq_operations structs const, to help mitigate against
revectoring user-triggerable function pointers.
This is derived from the grsecurity patch, although generated from scratch
because it's simpler than extracting the changes from there.
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When probing the device in tpm_tis_init the call request_locality
uses timeout_a, which wasn't being initalized until after
request_locality. This results in request_locality falsely timing
out if the chip is still starting. Move the initialization to before
request_locality.
This probably only matters for embedded cases (ie mine), a BIOS likely
gets the TPM into a state where this code path isn't necessary.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_event_name uses sprintf to fill a buffer declared on the stack. It fills
the buffer 2 bytes at a time. What the code doesn't take into account is that
sprintf(buf, "%02x", data) actually writes 3 bytes. 2 bytes for the data and
then it nul terminates the string. Since we declare buf to be 40 characters
long and then we write 40 bytes of data into buf sprintf is going to write 41
characters. The fix is to leave room in buf for the nul terminator.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
This patch fixes the bug reported in
http://bugzilla.kernel.org/show_bug.cgi?id=11681.
"Lots of device drivers register a 'struct device_driver' with
the '.bus' member set to '&platform_bus_type'. This is wrong,
since the platform_bus functions expect the 'struct device_driver'
to be wrapped up in a 'struct platform_driver' which provides
some additional callbacks (like suspend_late, resume_early).
The effect may be that platform_suspend_late() uses bogus data
outside the device_driver struct as a pointer pointer to the
device driver's suspend_late() function or other hard to
reproduce failures."(Lothar Wassmann)
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
