The Cintiq 24HD has three LEDs on the left side of the tablet and
three LEDs on the right side of the tablet. Switching to LED 0,
1, or 2 will enable the top, middle, or bottom LED for the respective
side. Switching to LED 3 turns off the LEDs on the respective side.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adds support for the Cintiq 24HD. There are two quirks about this
model that haven't been seen in prior tablets. First, a second
touch ring is present on this display; it is being exposed via the
ABS_THROTTLE axis. Second, three capacitive buttons at the top of
the unit are available; though physically a touch strip, we report
the use of these buttons with generic KEY_ events.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With commit 67d0a07544 we mark strict_strtox
as obsolete. Convert all remaining such uses in drivers/input/.
Also change long to appropriate types, and return error conditions
from kstrtox separately, as Dmitry sugguests.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bamboo's Pen and Touch packets always start with a value
of 0x02 in first byte. In 3rd gen Bamboo's, the hw is now
periodically sending some additional packets with unrelated data
and uses a value other than 0x02 to inform driver this.
Ignore those packets now.
This was reported by users as bad behavior in Gimp. The
invalid packets being processed made the stylus report
out of proximity for the 1 packet and this triggered some
secondary bug which caused Gimp to stop drawing until
user really took pen out of proximity of tablet.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
3rd generation Bamboo Pen and Touch tablets reuse the older
stylus packet but add an extra fixed zero pad byte to end.
The touch packets are quite different since it supports tracking
of up to 16 touches. The packet is 64-byte fixed size but contains
up to 15 smaller messages indicating data for a single touch or
for tablet button presses.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Override invalid pen based pktlen and x/y_max with touch
values from HID report.
Since active area of pen and touch are same on these
devices, set physical x/y size while pen x/y_max and
resolution are still valid.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bit 0x02 always means tip versus eraser. Bit 0x01 is something related
to version of stylus and different values are starting to be used.
Relaxing proximity check is required to be used with 3rd generation
Bamboo Pen and Touch tablets.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bamboo's do not declared a Digitizer-Stylus so the if() was
never executed. wacom_features already contains correct stylus
packet length.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Only the stylus interface on Bamboo's has a feature report that can
be used to set to wacom mode. The touch interface only has 1 report mode
and will return errors for those get/sets requests.
The get request was always erroring out because it was not marked as
an input request. Only down side of error was needlessly resending the
set request 5 times.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Medium size Bamboo P&T driver reused max X/Y form older Bamboo 1
medium size tablets and never updated to real value. Actual
active area of tablet is slightly larger in Y direction.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Tablet reports a distance of 0 right at highest point possible
to be in proximity and distance_max when touching tablet. Inverse
the distance since user land has no way of knowing ABS_DISTANCE
is not distance from tablet.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
These were left in during removal of touch pressure reports but not
needed now.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cintiq 21ux2 has two sets of four LEDs on right and left side of
the tablet, respectively.
Reviewed-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The LED also indicates the status of the tablet. Don't turn it off.
Reviewed-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The LED luminance level is normally lower when no button is pressed.
Reviewed-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This reverts commit 71c86ce597.
The 21UX2 does have touchstrips, but they are in a somewhat-
hidden location.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bamboos with Product ID's > 0xD4 return values unrelated to pressure
in touch 1 pressure field. They also report 2nd touch X/Y values
shifted down 1 byte (where pressure was). This results in jumpy
1 finger touch and totally invalid 2nd finger data.
For touch detection, switch to a Touch Present single bit that
all versions of Bamboo support.
For touch 2 offset, calculate offset based on a bit that is set
different between the two packet layouts.
Since touch pressure reports were removed from driver, there was
no need to be reading pressure any more.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adds INPUT_PROP_POINTER or INPUT_PROP_DIRECT as necessary to the
hardware supported by the Wacom driver. The DIRECT property is
assigned to devices with an embedded screen (i.e. touchscreens
and display tablets). The POINTER property is assigned to those
without embedded screens.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This commit enables control of the LEDs and OLED displays found on the
Wacom Intuos4 M, L, and XL. For this purpose, a new "wacom_led" attribute
group is added to the sysfs entry of the USB device.
This "wacom_led" group only shows up when the correct device (M, L, or XL)
is detected. The attributes are described in
Documentation/ABI/testing/sysfs-wacom
Signed-off-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Wacom PenPartner should advertise its stylus tip and button
in addition to the eraser tool. These are both physically
present on the hardware, and emitted from 'wacom_penpartner_irq'.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The old code may call input_sync() without sending any other events.
While it will be suppressed by the input core not calling it at all
is still cheaper.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bamboo touch sets BTN_BACK, BTN_FORWARD, BTN_LEFT, and BTN_RIGHT
as the default button events for tablet buttons. Change Graphire4
and old Bamboo to the same settings.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With the removal of BTN_TOOL_FINGER for tablet buttons and
expresskeys, serial number is needed to distingush if the
events were from a regular tool (stylus, eraser, or mouse)
or the attribures (buttons, strips, or wheels) on the tablet
since there are overlapped events between the tools and the
tablet attributes.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
BTN_TOOL_FINGER was designed to indicate a single finger touch.
Remove the lines that borrowed this type for expresskeys and
tablet buttons.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Wacom DTU-2231 tablet has two interfaces on its default configuration
and both have HID class, leading to the creation of two input devices
instead of one. Only the first one is used, so filter out the second.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Touch resolution is reported to the userland by retrieving the value
from the HID descriptor. But pen resolution is not since it can not
be retrieved. The current Wacom X driver has a resolution table.
To centralize the source of these values, the resolution entries are
added in the wacom_features struct for x and y coordinates respectively.
The values are then reported to the userland.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are two types of 1FGT devices supported in wacom_wac.c.
Changing them to follow the existing touchscreen format, i.e.,
only report BTN_TOUCH as a valid tool type.
Touch data will be ignored if pen is in proximity. This requires
a touch up event sent if touch was down when pen comes in. The
touch up event should be sent before any pen events are emitted.
Otherwise, two pointers would race for the cursor.
However, we can not send a touch up inside wacom_tpc_pen since
pen and touch are on different logical port. That is why we
have to check if touch is up before sending pen events.
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
So it would be easier for patch reviewers to follow the data path.
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2FGT Tablet PC touch events were processed in _TAP_ format. Remove
them so we can change to _MT_ format.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If we fail to retrieve HID descriptor we need to free allocated URB so
jump to proper label to do that.
Signed-off-by: Alexander Strakh <strakh@ispras.ru>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also remove fake ABS_RX/ABS_RY "axes" that were used to report physical
dimensions now that we have better way.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
