* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Support creation of FMRs with pages smaller than 4K
IB/ehca: Fix function return types
RDMA/cxgb3: Bump up the MPA connection setup timeout.
RDMA/cxgb3: Silently ignore close reply after abort.
RDMA/cxgb3: QP flush fixes
IB/ipoib: Fix transmit queue stalling forever
IB/mlx4: Fix off-by-one errors in calls to mlx4_ib_free_cq_buf()
Don't hard code a test against a minimum page shift of 12, since the
device may support smaller pages. Test against the actual smallest
page size from the device capabilities.
Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
rose: Wrong list_lock argument in rose_node seqops
netns: Fix reassembly timer to use the right namespace
netns: Fix device renaming for sysfs
bnx2: Update version to 1.7.5.
bnx2: Update RV2P firmware for 5709.
bnx2: Zero out context memory for 5709.
bnx2: Fix register test on 5709.
bnx2: Fix remote PHY initial link state.
bnx2: Refine remote PHY locking.
bridge: forwarding table information for >256 devices
tg3: Update version to 3.92
tg3: Add link state reporting to UMP firmware
tg3: Fix ethtool loopback test for 5761 BX devices
tg3: Fix 5761 NVRAM sizes
tg3: Use constant 500KHz MI clock on adapters with a CPMU
hci_usb.h: fix hard-to-trigger race
dccp: ccid2.c, ccid3.c use clamp(), clamp_t()
net: remove NR_CPUS arrays in net/core/dev.c
net: use get/put_unaligned_* helpers
bluetooth: use get/put_unaligned_* helpers
...
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Bolt in SLB entry for kernel stack on secondary cpus
[POWERPC] PS3: Update ps3_defconfig
[POWERPC] PS3: Remove unsupported wakeup sources
[POWERPC] PS3: Make ps3_virq_setup and ps3_virq_destroy static
[POWERPC] PS3: Add time include to lpm
[POWERPC] Fix slb.c compile warnings
[POWERPC] Xilinx: Fix compile warnings
[POWERPC] Squash build warning for print of resource_size_t in fsl_soc.c
[RAPIDIO] fix current kernel-doc notation
[POWERPC] 86xx: mpc8610_hpcd: add support for PCI Express x8 slot
Fix a potential issue in mpc52xx uart driver
[POWERPC] mpc5200: Allow for fixed speed MII configurations
[POWERPC] 86xx: Fix the wrong serial1 interrupt for 8610 board
The new RV2P firmware fixes 2 issues:
1. The jumbo rx buffer page size is now configurable and set to the
proper PAGE_SIZE. Before, it was assumed to be always 4K.
2. Driver sometimes would crash when receiving jumbo packets mixed
with firmware management packets. This was caused by the old
firmware DMA'ing to the wrong address.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should zero out the context memory for 5709 before each reset. When
we resume after suspend for example, the memory may not be zero and the
chip may not function correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register BNX2_CTX_STATUS (0x1004) should be skipped on 5709 as it
contains reserved bits.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some remote PHY blade systems, the driver receives no initial link
interrupt. As a result, the GMII/MII MAC mode does not get setup properly.
To fix this problem, we add an initial poll of the link state after chip
reset.
With this change, the setting of the initial carrier state in the init
code can be eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2_set_remote_link() should be called under bp->phy_lock to protect
against concurrent polling and interrupt calls. This change is needed
by the next patch which will add one initial poll of the remote PHY
link status.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the version number to 3.92.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All variants of the 5714, 5715, and 5780 offer a feature called the
"Universal Management Port". This feature is implemented in firmware
and is largely transparent to the driver, except...
It turns out that the UMP firmware needs to know the current status
of the link. Because the firmware cannot touch the PHY registers while
the driver is in control of the device, it needs the driver to report
link status changes through an additional handshaking mechanism.
Without this handshake, it has been observed in the field that the UMP
firmware will not operate correctly.
This patch implements the new handshake with the UMP firmware. Since
the handshake uses the same mechanism ASF heartbeats use, code was
added to detect and wait for completion of a pending previous event.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A CPMU related loopback test bug existed for AX revisions of the 5761.
While that errata has been fixed, the CPMU still slows down the core
clock too far to run the loopback test successfully. This patch
disables the CPMU LINK_SPEED mode just like we do with the AX
revisions of the 5761 and all revisions of the 5784.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5761 NVRAM sizes assigned to the nvram_size member are half as big
as they should be. This patch corrects the NVRAM sizes and replaces
the hardcoded constants with preprocessor constants for readability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MI clock is not configured correctly on adapters with the CPMU
present. The tg3 driver has code which statically sets the MI clock to
be a fraction of the speed at which the core clock is running.
However, the CPMU can change the adapter's core clock frequency based
on operating conditions. Consequently, the MI will run slow when the
core's clock has been slowed down.
There is a new 500KHz constant frequency clock available on adapters
with a CPMU. This patch removes the static core clock scaling and
configures the MI clock to use this new 500KHz clock instead.
Running the MI clock at slower speeds will not directly result in data
corruption, but it does challenge the PHY read and write routine timeouts.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent proposed feature addition to the virtio block driver revealed
some flaws in the API: in particular, we assume that feature
negotiation is complete once a driver's probe function returns.
There is nothing in the API to require this, however, and even I
didn't notice when it was violated.
So instead, we require the driver to specify what features it supports
in a table, we can then move the feature negotiation into the virtio
core. The intersection of device and driver features are presented in
a new 'features' bitmap in the struct virtio_device.
Note that this highlights the difference between Linux unsigned-long
bitmaps where each unsigned long is in native endian, and a
straight-forward little-endian array of bytes.
Drivers can still remove feature bits in their probe routine if they
really have to.
API changes:
- dev->config->feature() no longer gets and acks a feature.
- drivers should advertise their features in the 'feature_table' field
- use virtio_has_feature() for extra sanity when checking feature bits
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
So, we previously had a 'VIRTIO_NET_F_GSO' bit which meant that 'the
host can handle csum offload, and any TSO (v4&v6 incl ECN) or UFO
packets you might want to send. I thought this was good enough for
Linux, but it actually isn't, since we don't do UFO in software.
So, add separate feature bits for what the host can handle. Add
equivalent ones for the guest to say what it can handle, because LRO
is coming too (thanks Herbert!).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Herbert tells me that returning NETDEV_TX_BUSY from hard_start_xmit is
seen as a poor thing to do; we should cache the packet and stop the queue.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu points out (within another patch) that my scatterlists are
too short: one entry for the gso header, one for the skb->data, and
MAX_SKB_FRAGS for all the fragments.
Fix both xmit and recv sides (recv currently unused, coming in later
patch).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
get_buf() gives the length written by the other side, which will be
zero. We want to add the skb length.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
There was an obvious typo in LED structure
initialization which caused the radio and quality/activity
leds to be incorrectly initialized which resulted in
the leds not being enabled.
Additionally add the rt2x00led_led_activity() handler
that will enable TX/RX activity leds when the radio
is being enabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The timing settings for 1MBs should exclude
the short preamble bit since that only applies
to 2MBs, 5.5MBs and 11MBs.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
direct_mask will be set when we are not associated and requesting a
direct scan. The second debug print will be confusing as priv->essid
is not set at that time and it will thus print "<hidden>" while it is
known to which AP a direct scan is requested - as previous debug message
also indicates.
Now make all debugging consistent.
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All channels should be scanned, including the current channel
when the client is associated.
Removed also unused flag to scan only active channels.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some TX/RX related locking issues.
With this patch applied, some of the PHY transmission errors are fixed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various improvements for configuring the MPC5200 MII link from the
device tree:
* Look for 'current-speed' property for fixed speed MII links
* Look for 'fsl,7-wire-mode' property for boards using the 7 wire mode
* move definition of private data structure out of the header file
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
It's easy: grab locks before talking to hardware and realease
them afterwards. The one big lock has been splitted into a hw_lock
and mii_lock.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
linux-2.6-mk68/drivers/net/fec.c: In function 'fec_enet_module_init':
linux-2.6-mk68/drivers/net/fec.c:2627: warning: unused variable 'j'
linux-2.6-mk68/drivers/net/fec.c: At top level:
linux-2.6-mk68/drivers/net/fec.c:2136: warning: 'mii_link_interrupt' defined but not used
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the acquisition of unused interrupt types. We don't need to
register all the TX and RX varients used on some ColdFire FEC hardware.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Renamed the 5272 hash_table registers to match the "grp" hash_table
registers of the other ColdFire parts. They are actually a group hash.
The makes for consistent setup across all ColdFire parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to Coverity (kudo's to Adrian Bunk), we had one use-before-check
bug in libe libertas driver. This patch fixes this issue.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes operation of dual-PHY (A/B/G) devices.
Do not anounce the A-PHY to mac80211, as that's not supported, yet.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (53 commits)
tcp: Overflow bug in Vegas
[IPv4] UFO: prevent generation of chained skb destined to UFO device
iwlwifi: move the selects to the tristate drivers
ipv4: annotate a few functions __init in ipconfig.c
atm: ambassador: vcc_sf semaphore to mutex
MAINTAINERS: The socketcan-core list is subscribers-only.
netfilter: nf_conntrack: padding breaks conntrack hash on ARM
ipv4: Update MTU to all related cache entries in ip_rt_frag_needed()
sch_sfq: use del_timer_sync() in sfq_destroy()
net: Add compat support for getsockopt (MCAST_MSFILTER)
net: Several cleanups for the setsockopt compat support.
ipvs: fix oops in backup for fwmark conn templates
bridge: kernel panic when unloading bridge module
bridge: fix error handling in br_add_if()
netfilter: {nfnetlink,ip,ip6}_queue: fix skb_over_panic when enlarging packets
netfilter: x_tables: fix net namespace leak when reading /proc/net/xxx_tables_names
netfilter: xt_TCPOPTSTRIP: signed tcphoff for ipv6_skip_exthdr() retval
tcp: Limit cwnd growth when deferring for GSO
tcp: Allow send-limited cwnd to grow up to max_burst when gso disabled
[netdrvr] gianfar: Determine TBIPA value dynamically
...
Something Arjan suggested which allows us to clean up the code nicely
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use the tty baud functions
- Call driver termios methods directly holding the right locking
- Check for a write method
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Operations are now a shared const function block as with most other Linux
objects
- Introduce wrappers for some optional functions to get consistent behaviour
- Wrap put_char which used to be patched by the tty layer
- Document which functions are needed/optional
- Make put_char report success/fail
- Cache the driver->ops pointer in the tty as tty->ops
- Remove various surplus lock calls we no longer need
- Remove proc_write method as noted by Alexey Dobriyan
- Introduce some missing sanity checks where certain driver/ldisc
combinations would oops as they didn't check needed methods were present
[akpm@linux-foundation.org: fix fs/compat_ioctl.c build]
[akpm@linux-foundation.org: fix isicom]
[akpm@linux-foundation.org: fix arch/ia64/hp/sim/simserial.c build]
[akpm@linux-foundation.org: fix kgdb]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver somehow escaped the tty operations changes way back when. Update
it so that we can switch to tty->ops shortly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves the following select's:
- RFKILL : IWLWIFI_RFKILL -> IWLCORE
- RFKILL_INPUT : IWLWIFI_RFKILL -> IWLCORE
- MAC80211_LEDS : IWL4965_LEDS -> IWLCORE
- LEDS_CLASS : IWL4965_LEDS -> IWLCORE
- MAC80211_LEDS : IWL3945_LEDS -> IWL3945
- LEDS_CLASS : IWL3945_LEDS -> IWL3945
The effects are:
- with IWLCORE=m and/or IWL3945=m RFKILL/RFKILL_INPUT/MAC80211_LEDS/LEDS_CLASS
are no longer wrongly forced to y
- fixes a build error with IWLCORE=y, IWL4965=m
might be a bug in kconfig causing it, but doing this change that is
anyway the right thing fixes it
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a FMR is unmapped, mlx4 resets the map count to 0, and clears the
upper part of the R_Key which is used as the sequence counter.
This poses a problem for RDS, which uses ib_fmr_unmap as a fence
operation. RDS assumes that after issuing an unmap, the old R_Keys
will be invalid for a "reasonable" period of time. For instance,
Oracle processes uses shared memory buffers allocated from a pool of
buffers. When a process dies, we want to reclaim these buffers -- but
we must make sure there are no pending RDMA operations to/from those
buffers. The only way to achieve that is by using unmap and sync the
TPT.
However, when the sequence count is reset on unmap, there is a high
likelihood that a new mapping will be given the same R_Key that was
issued a few milliseconds ago.
To prevent this, don't reset the sequence count when unmapping a FMR.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Open MPI, Intel MPI and other applications don't respect the iWARP
requirement that the client (active) side of the connection send the
first RDMA message. This class of application connection setup is
called peer-to-peer. Typically once the connection is setup, _both_
sides want to send data.
This patch enables supporting peer-to-peer over the chelsio RNIC by
enforcing this iWARP requirement in the driver itself as part of RDMA
connection setup.
Connection setup is extended, when the peer2peer module option is 1,
such that the MPA initiator will send a 0B Read (the RTR) just after
connection setup. The MPA responder will suspend SQ processing until
the RTR message is received and reply-to.
In the longer term, this will be handled in a standardized way by
enhancing the MPA negotiation so peers can indicate whether they
want/need the RTR and what type of RTR (0B read, 0B write, or 0B send)
should be sent. This will be done by standardizing a few bits of the
private data in order to negotiate all this. However this patch
enables peer-to-peer applications now and allows most of the required
firmware and driver changes to be done and tested now.
Design:
- Add a module option, peer2peer, to enable this mode.
- New firmware support for peer-to-peer mode:
- a new bit in the rdma_init WR to tell it to do peer-2-peer
and what form of RTR message to send or expect.
- process _all_ preposted recvs before moving the connection
into rdma mode.
- passive side: defer completing the rdma_init WR until all
pre-posted recvs are processed. Suspend SQ processing until
the RTR is received.
- active side: expect and process the 0B read WR on offload TX
queue. Defer completing the rdma_init WR until all
pre-posted recvs are processed. Suspend SQ processing until
the 0B read WR is processed from the offload TX queue.
- If peer2peer is set, driver posts 0B read request on offload TX
queue just after posting the rdma_init WR to the offload TX queue.
- Add CQ poll logic to ignore unsolicitied read responses.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Extend the mlx4_cq_resize() API with a way to set the "collapsed" flag
for the CQ being created.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Yeah, in practice they both mean "root", but Alan correctly points out
that anybody who gets to do raw IO space accesses should really be using
CAP_SYS_RAWIO rather than CAP_NET_ADMIN.
Pointed-out-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[RAPIDIO] Change RapidIO doorbell source and target ID field to 16-bit
[RAPIDIO] Add RapidIO connection info print out and re-training for broken connections
[RAPIDIO] Add serial RapidIO controller support, which includes MPC8548, MPC8641
[RAPIDIO] Add RapidIO node probing into MPC86xx_HPCN board id table
[RAPIDIO] Add RapidIO node into MPC8641HPCN dts file
[RAPIDIO] Auto-probe the RapidIO system size
[RAPIDIO] Add OF-tree support to RapidIO controller driver
[RAPIDIO] Add RapidIO multi mport support
[RAPIDIO] Move include/asm-ppc/rio.h to asm-powerpc
[RAPIDIO] Add RapidIO option to kernel configuration
[RAPIDIO] Change RIO function mpc85xx_ to fsl_
[POWERPC] Provide walk_memory_resource() for powerpc
[POWERPC] Update lmb data structures for hotplug memory add/remove
[POWERPC] Hotplug memory remove notifications for powerpc
[POWERPC] windfarm: Add PowerMac 12,1 support
[POWERPC] Fix building of pmac32 when CONFIG_NVRAM=m
[POWERPC] Add IRQSTACKS support on ppc32
[POWERPC] Use __always_inline for xchg* and cmpxchg*
[POWERPC] Add fast little-endian switch system call
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
