sata_inic162x is now ready for production use. Bump the version,
explain what's working and what's not and drop EXPERIMENTAL.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When attached to cardbus, mmio region is at BAR 1. Other than that,
everything else is the same. Add support for it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_inic162x now doesn't use any SFF features. Remove all SFF
related stuff.
* Mask unsolicited ATA interrupts. This removes our primary source of
spurious interrupts and spurious interrupt handling can be tightened
up. There's no need to clear ATA interrupts by reading status
register either.
* Don't dance with IDMA_CTL_ATA_NIEN and simplify accesses to
IDMA_CTL.
* Inherit from sata_port_ops instead of ata_sff_port_ops.
* Don't initialize or use ioaddr. There's no need to map BAR0-4
anymore.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use IDMA for ATAPI commands. Write and some misc commands time out
when executed using ATAPI_PROT_DMA but ATAPI_PROT_PIO works fine. As
PIO is driven by DMA too, it doesn't make any noticeable difference
for native SATA devices. inic_check_atapi_dma() is implemented to
force PIO for those ATAPI commands.
After this change, sata_inic162x issues all commands using IDMA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use IDMA for PIO and non-data commands. This allows sata_inic162x to
safely drive LBA48 devices. Kill inic_dev_config() which contains
code to reject LBA48 devices.
With this change, status checking in inic_qc_issue() to avoid hard
lock up after hotplug can go away too.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The modified driver on initio site has enough clue on how to use IDMA.
Use IDMA for ATA_PROT_DMA.
* LBA48 now works as long as it uses DMA (LBA48 devices still aren't
allowed as it can destroy data if PIO is used for any reason).
* No need to mask IRQs for read DMAs as IDMA_DONE is properly raised
after transfer to memory is actually completed. There will be some
spurious interrupts but host_intr will handle it correctly and
manipulating port IRQ mask interacts badly with the other port for
some reason, so command type dependent port IRQ masking is not used
anymore.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
inic162x can't reliably read back TF or at least we don't know how to
do it yet. The only values which seem reliable are status and error.
This patch updates access to TF.
* implement inic_tf_read() which reads the TF area in mmio area
* implement custom inic_qc_fill_rtf() which only returns true if
status indicates device error. it'll be returning bogus addresses
for device errors but it'll be able to report why it failed at
least.
* implement custom inic_check_ready() and use ata_wait_after_reset()
instead of the SFF version.
* use inic_tf_read() for classification.
This is not perfect but it fixes hotplug detection failure and at
least makes the driver report 0's instead of random garbages while
reporting valid status and error for device errors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* add a bunch of constants, most are from the datasheet, a few
undocumented ones are from initio's modified driver
* HCTL_PWRDWN is bit 12 not 13
This is in preparation of further inic162x updates.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* use larger indents for structure member definitions
* kill unused variable @addr in inic_scr_write()
* kill unnecessary flushes in inic_freeze/thaw()
* kill buggy explicit kfree() on devres managed port private data
This is in preparation of further inic162x updates.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some tidying as suggested by Grant Grundler.
Nuke local bit-counting function from sata_mv in favour of using hweight16().
Also add a short explanation for the 15msec timeout used when waiting for empty/idle.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Convert sata_mv's EH for FIS-based switching (FBS) over to the
sequence recommended by Marvell. This enables us to catch/analyze
multiple failed links on a port-multiplier when using NCQ.
To do this, we clear the ERR_DEV bit in the EDMA Halt-Conditions register,
so that the EDMA engine doesn't self-disable on the first NCQ error.
Our EH code sets the MV_PP_FLAG_DELAYED_EH flag to prevent new commands
being queued while we await completion of all outstanding NCQ commands
on all links of the failed PM.
The SATA Test Control register tells us which links have failed,
so we must only wait for any other active links to finish up
before we stop the EDMA and run the .error_handler afterward.
The patch also includes skeleton code for handling of non-NCQ FBS operation.
This is more for documentation purposes right now, as that mode is not yet
enabled in sata_mv.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce a new "delayed error handling" mechanism in sata_mv,
to enable us to eventually deal with multiple simultaneous NCQ
failures on a single host link when a PM is present.
This involves a port flag (MV_PP_FLAG_DELAYED_EH) to prevent new
commands being queued, and a pmp bitmap to indicate which pmp links
had NCQ errors.
The new mv_pmp_error_handler() uses those values to invoke
ata_eh_analyze_ncq_error() on each failed link, prior to freezing
the port and passing control to sata_pmp_error_handler().
This is based upon a strategy suggested by Tejun.
For now, we just implement the delayed mechanism.
The next patch in this series will add the multiple-NCQ EH code
to take advantage of it.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Export ata_eh_analyze_ncq_error() for subsequent use by sata_mv,
as suggested by Tejun.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Separate out the inner loop body of mv_host_intr()
into it's own function called mv_port_intr().
This should help maintainabilty.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the unwanted reads of hc_irq_cause from mv_host_intr(),
thereby removing a bug whereby we were not always reading it when needed..
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sigh. Undo some earlier changes to mv_port_intr(),
so that we now read/clear SError again in all cases.
Arrange the top of the function to be as close as possible
to what we need for a later update (in this series) for ERR_DEV handling.
Fix things so that libata-eh can attempt a READ_LOG_EXT_10H
in response to a failed NCQ command, by just doing a local
mv_eh_freeze() rather than ata_port_freeze().
This will now fully handle NCQ errors much of the time,
but more fixes are needed for FBS/PMP, and for certain chip errata.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange mv_config_fbs() to more closely follow the (corrected) datasheet
recommendations for NCQ and FIS-based switching (FBS).
Also, maintain a port flag to let us know when FBS is enabled.
We will make more use of that flag later in this patch series.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part 1 of workaround for errata "sata#25" for the 60x1 series
(the second half of this errata workaround is still in development.
Bit22 of the GPIO port has to be set "on" when in NCQ mode.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The EDMA engine cannot tolerate a mix of NCQ/non-NCQ commands,
and cannot be used for PIO at all. So we need to prevent libata
from trying to feed us such mixtures.
Introduce mv_qc_defer() for this purpose, and use it for all chip versions.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When performing EH, it is recommended to wait for the EDMA engine
to empty out requests-in-progress before disabling EDMA.
Introduce code to poll the EDMA_STATUS register for idle/empty bits
before disabling EDMA. For non-EH operation, this will normally exit
without delay, other than the register read.
A later series of patches may focus on eliminating this and various
other register reads (when possible) throughout the driver,
but for now we're focussing on solid reliablity.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some of the GenIIe EDMA optimizations should not be used
for non-PCI (SOC) devices, and nor for certain configurations
of conventional PCI (non PCI-X, PCIe) buses.
Logic taken/simplified from that in the Marvell proprietary driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
More cosmetic changes; no code changes.
-- try and improve consistency of naming.
-- add missing _OFS to tails of register offset definitions.
-- rename mv_setup_ifctl() to mv_setup_ifcfg(), since that's what it really does.
-- remove/move some dead comments
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On certain configurations (certain macbooks), even though all the
conditions for SIDPR access described in the datasheet are met,
actually reading those registers just returns 0 and have no effect on
write. Verify SIDPR is actually working before enabling it.
This is reported by Ryan Roth in bz#10512.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ryan Roth <ryan.roth@ch2m.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that
the device isn't ready yet. It looks like they use 0xff if device
presence is detected but connection isn't established. 0x77 or 0x7f
after connection is established and use the value from signature FIS
after receiving it.
This patch implements ata_check_ready(), which takes TF status value
and determines whether the port is ready or not considering the above
and other conditions, and use it in @check_ready() functions. This is
safe as both 0x77 and 0x7f aren't valid ready status value even though
they have BSY bit cleared.
This fixes hot plug detection failures which can be triggered with
certain drives if they aren't already spun up when the data connector
is hot plugged.
Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with
eight drives from all major vendors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Support creation of FMRs with pages smaller than 4K
IB/ehca: Fix function return types
RDMA/cxgb3: Bump up the MPA connection setup timeout.
RDMA/cxgb3: Silently ignore close reply after abort.
RDMA/cxgb3: QP flush fixes
IB/ipoib: Fix transmit queue stalling forever
IB/mlx4: Fix off-by-one errors in calls to mlx4_ib_free_cq_buf()
Don't hard code a test against a minimum page shift of 12, since the
device may support smaller pages. Test against the actual smallest
page size from the device capabilities.
Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Also remove duplicate assignment of local_ca_ack_delay and change
min_t check for local_ca_ack_delay to u8 instead of int.
Signed-off-by: Stefan Roscher <stefan.roscher at de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 06916639e2 ("driver-core: add
dev_name() to help transition away from using bus_id") added a static
inline dev_name() and used it in dev_printk.
Unfortunately, drivers/edac/edac_core.h defines a macro called
dev_name(). Rename the latter.
Diagnosis by Tony Breeds and Michael Ellerman.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86 PCI: call dmi_check_pciprobe()
x86/pci: add pci=skip_isa_align command lines.
x86/pci: remove flag in pci_cfg_space_size_ext
x86: fix section mismatch in pci_scan_bus
The new mac_esp scsi driver needs CONFIG_SCSI_SPI_ATTRS, just like all other
drivers using the new esp_scsi core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/input/serio/hp_sdc.c: In function 'hp_sdc_take':
drivers/input/serio/hp_sdc.c:198: error: implicit declaration of function 'up'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The single step test is not terribly costly and it should be able to
pass at 1000 loops successfully in under 1 second. A non-kgdb timing
regression was found using this test, but it did not occur frequently
because by default the test was only executed a single time.
This patch changes the default for the single step test to 1000
iterations and allows for individual configuration of the single step
test to further exercise the kgdb subsystem when needed.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Shadowed variable and integer as NULL pointer fixes:
drivers/misc/kgdbts.c:877:6: warning: symbol 'sys_open_test' shadows an earlier one
drivers/misc/kgdbts.c:537:27: originally declared here
drivers/misc/kgdbts.c:378:22: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:386:22: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:468:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:472:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:502:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:506:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:509:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:523:20: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:527:20: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:530:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:541:21: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:545:21: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:548:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:559:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:563:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:573:16: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:574:19: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:578:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:588:16: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:589:19: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:593:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:602:16: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:604:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:925:3: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:938:3: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch re-ordering could be harmful:
commit 1fd1890594
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Sat Apr 26 22:25:24 2008 +0200
ide: add IDE_HFLAG_SERIALIZE_DMA host flag
...
is buggy because ->init_dma method / ide_hwif_setup_dma() is called
before IDE_HFLAG_SERIALIZE_DMA host flag is checked.
Fix it by checking IDE_HFLAG_SERIALIZE[_DMA] after DMA initialization.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
rose: Wrong list_lock argument in rose_node seqops
netns: Fix reassembly timer to use the right namespace
netns: Fix device renaming for sysfs
bnx2: Update version to 1.7.5.
bnx2: Update RV2P firmware for 5709.
bnx2: Zero out context memory for 5709.
bnx2: Fix register test on 5709.
bnx2: Fix remote PHY initial link state.
bnx2: Refine remote PHY locking.
bridge: forwarding table information for >256 devices
tg3: Update version to 3.92
tg3: Add link state reporting to UMP firmware
tg3: Fix ethtool loopback test for 5761 BX devices
tg3: Fix 5761 NVRAM sizes
tg3: Use constant 500KHz MI clock on adapters with a CPMU
hci_usb.h: fix hard-to-trigger race
dccp: ccid2.c, ccid3.c use clamp(), clamp_t()
net: remove NR_CPUS arrays in net/core/dev.c
net: use get/put_unaligned_* helpers
bluetooth: use get/put_unaligned_* helpers
...
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Bolt in SLB entry for kernel stack on secondary cpus
[POWERPC] PS3: Update ps3_defconfig
[POWERPC] PS3: Remove unsupported wakeup sources
[POWERPC] PS3: Make ps3_virq_setup and ps3_virq_destroy static
[POWERPC] PS3: Add time include to lpm
[POWERPC] Fix slb.c compile warnings
[POWERPC] Xilinx: Fix compile warnings
[POWERPC] Squash build warning for print of resource_size_t in fsl_soc.c
[RAPIDIO] fix current kernel-doc notation
[POWERPC] 86xx: mpc8610_hpcd: add support for PCI Express x8 slot
Fix a potential issue in mpc52xx uart driver
[POWERPC] mpc5200: Allow for fixed speed MII configurations
[POWERPC] 86xx: Fix the wrong serial1 interrupt for 8610 board
The new RV2P firmware fixes 2 issues:
1. The jumbo rx buffer page size is now configurable and set to the
proper PAGE_SIZE. Before, it was assumed to be always 4K.
2. Driver sometimes would crash when receiving jumbo packets mixed
with firmware management packets. This was caused by the old
firmware DMA'ing to the wrong address.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should zero out the context memory for 5709 before each reset. When
we resume after suspend for example, the memory may not be zero and the
chip may not function correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register BNX2_CTX_STATUS (0x1004) should be skipped on 5709 as it
contains reserved bits.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
