One or two ancient drives predated the cable spec and didn't sent the
valid bits for the field. I had hoped to leave this out of libata as a
piece of historical annoyance but a recent CD drive shows the same bug so
we have to import support for it.
Same concept as Bartlomiej's changes old IDE except that as we have
centralised blacklists we can avoid keeping another private table of stuff
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A colleague noticed recent versions of Ubuntu no longer detect his 80 GB
ST380020ACE drive. This drive is special in that it advertises LBA48 support,
but has the lba_capacity_2 field set to zero (cfr.
http://lkml.org/lkml/2004/3/30/163).
Upon closer look, libata indeed doesn't seem to handle this case yet.
Below is an (untested) fix.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commands sent to ATAPI tape drives via the SCSI generic (sg) driver are
limited in the amount of data that they can transfer by the max_sectors
value. The max_sectors value is currently calculated according to the
command set for disk drives, which doesn't apply to tape drives. The
default max_sectors value of 256 limits ATAPI tape drive commands to
128 KB. This patch against 2.6.24-rc1 increases the max_sectors value
for tape drives to 65535, which permits tape drive commands to transfer
just under 32 MB.
Tested with a SuperMicro PDSME motherboard, AHCI, and a Sony SDX-570V
SATA tape drive.
Note that some of the chipset drivers also set their own max_sectors
value, which may override the value set in libata-core. I don't have
any of these chipsets to test, so I didn't go messing with them. Also,
ATAPI devices other than tape drives may benefit from similar changes,
but I have only tape drives and disk drives to test.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Device Initiated Power Management, which is defined
in SATA 2.5 can be enabled for disks which support it.
This patch enables DIPM when the user sets the link
power management policy to "min_power".
Additionally, libata drivers can define a function
(enable_pm) that will perform hardware specific actions to
enable whatever power management policy the user set up
for Host Initiated Power management (HIPM).
This power management policy will be activated after all
disks have been enumerated and intialized. Drivers should
also define disable_pm, which will turn off link power
management, but not change link power management policy.
Documentation/scsi/link_power_management_policy.txt has additional
information.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA devices in SLEEP mode don't respond to any commands. SRST is
necessary to wake it up. Till now, when a command is issued to a
device in SLEEP mode, the command times out, which makes EH reset the
device and retry the command after that, causing a long delay.
This patch makes libata track SLEEP state and issue SRST automatically
if a command is about to be issued to a device in SLEEP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bruce Allen <ballen@gravity.phys.uwm.edu>
Cc: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tackle the relatively sane complaints of checkpatch --file.
The vast majority is indentation and whitespace changes, the rest are
* #include fixes
* printk KERN_xxx prefix addition
* BSS/initializer cleanups
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This adds human-readable decoding of the ATA status and error registers
(similar to what drivers/ide does) as well as the SATA Serror register
to libata error handling output. This prevents the need to pore
through standards documents to figure out the meaning of the bits
in these registers when looking at error reports. Some bits that
drivers/ide decoded are not decoded here, since the bits are either
command-dependent or obsolete, and properly parsing them would add
too much complexity.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
[edited slightly to make output a bit more symmetric]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update AN support in preparation of PMP support.
* s/ata_id_has_AN/ata_id_has_atapi_AN/
* add AN enabled reporting during configuration
* add err_mask to AN configuration failure reporting
* update LOCKING comment for ata_scsi_media_change_notify()
* check whether ATA dev is attached to SCSI dev ata_scsi_media_change_notify()
* set ATA_FLAG_AN in ahci and sata_sil24
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ATA specifications require checks on certain flags before assuming
the validity of other data. Go through the methods and correct those
needing extra checks. Also note limits on ata_id_major_version with
respect to ATA-1 and ATA-2. Correct the 32bit PIO check.
Wants to sit in -mm for a bit in case of a screwup on my part that I
didn't hit on the test drives and also in case someone, somewhere has
a drive that gets it wrong.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Check to see if an ATAPI device supports Asynchronous Notification.
If so, enable it, if the host controller supports AN.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Debugging a report of a problem with an ancient solid state disk showed
up some problems in the IORDY handling
1. We check the wrong bit to see if the device has IORDY
2. Even then some ancient creaking piles of crap don't support
SETXFER at all.
The cases it fixes are obscure and the risk of side effects is slight
but possible. This also moves us slightly closer to supporting original
MFM/RLL disks with libata.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Add ATA_PIO[0-6] defines to <linux/ata.h>.
* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.
* Add PIO masks to host drivers.
<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add Port Multiplier related ATA constants and macros. Some of these
will be used by ata_link implementation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
INIT_DEV_PARAMS and SET_MULTI_MODE change the device parameters cached
by libata. Re-read IDENTIFY DEVICE info and update the cached device
paramters when seeing these commands.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(S)ATA drives can be configured for "power-up in standby",
a mode whereby a specific "spin up now!" command is required
before the first media access.
Currently, a drive with this feature enabled can not be used at all
with libata, and once in this mode, the drive becomes a doorstop.
The older drivers/ide subsystem at least enumerates the drive,
so that it can be woken up after the fact from a userspace HDIO_*
command, but not libata.
This patch adds support to libata for the "power-up in standby"
mode where a "spin up now!" command (SET_FEATURES) is needed.
With this, libata will recognize such drives, spin them up,
and then re-IDENTIFY them if necessary to get a full/complete
set of drive features data.
Drives in this state are determined by looking for
special values in id[2], as documented in the current ATA specs.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Add support for ignoring the BIOS HPA result (off by default) and setting
the disk to the full available size unless already frozen.
Tested with various platforms/disks and confirmed to work with the
Macintosh (which broke earlier) and ata_piix (breakage due to the LBA48
readback that Tejun fixed).
For normal users this brings us, I believe, to feature parity with old IDE
(and of course more featured in some areas too).
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The READ/WRITE LONG commands are theoretically obsolete,
but the majority of drives in existance still implement them.
The WRITE_LONG and WRITE_LONG_ONCE commands are of particular
interest for fault injection testing -- eg. creating "media errors"
at specific locations on a disk.
The fussy bit is that these commands require a non-standard
sector size, usually 520 bytes instead of 512.
This patch adds support to libata for READ/WRITE LONG commands
issued via SG_IO/ATA_16.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
patch 3/4:
The TORiSAN drive locks up when max sector == 256.
Limit max sector to 128 for the TORiSAN DRD-N216 drives.
(http://bugzilla.kernel.org/show_bug.cgi?id=6710)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 80c wire bit is bit 13, not 14. Bit 14 is always 1 if word93 is
implemented. This increases the chance of incorrect wire detection
especially because host side cable detection is often unreliable and
we sometimes soley depend on drive side cable detection. Fix the test
and add word93 validity check.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Kill _OFS suffixes in ATA_ID_{SERNO|FW_REV|PROD}_OFS for consistency
with other ATA_ID_* constants.
* Kill ATA_SERNO_LEN
* Add and use ATA_ID_SERNO_LEN, ATA_ID_FW_REV_LEN and ATA_ID_PROD_LEN.
This change also makes ata_device_blacklisted() use proper length
for fwrev.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The CFA world has some additional rules and drive modes we need to support for
newer expansion cards and on embedded boxes
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Also, moved ATA_MAX_SECTORS and ATA_MAX_SECTORS_LBA48 from
linux/libata.h to linux/ata.h, now that they truly reflect the standard
(well... mostly; note TODO comment).
This changes the performance profile (and potential bug profile)
for a bunch of drivers, so be wary.
HPA presence/enabled
HPA commands
Also add ata_id_is_cfa() as that is needed to detect and handle CF cards
which currently we reject.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recognize ATA_CMD_WRITE_MULTI_FUA_EXT as r/w multiple commands.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ATA major version calculation from ata_dev_identify()
into ata_id_major_version(). It's preparation for splitting
ata_dev_identify().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds suspend patch to libata, and ata_piix in particular. For
most low level drivers, they should just need to add the 4 hooks to
work. As I can only test ata_piix, I didn't enable it for more
though.
Suspend support is the single most important feature on a notebook, and
most new notebooks have sata drives. It's quite embarrassing that we
_still_ do not support this. Right now, it's perfectly possible to
suspend the drive in mid-transfer.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- add is_multi_taskfile() to ata.h
- initialize ata_device->multi_count with device identify data
- use ata_pio_sectors() to support r/w multiple commands
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
========
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
