* Pins 2 and 4 of switch 33 are documented as don't care on the PCB,
my testing seems to confirm this.
* I have been unable to do anything sensible with S1 set to on.
Am I missing something with regards to MMC1?
* Clarify which driver is needed for each switch setting.
* Should the AP4 board code be updated to allow the
SHDI driver to access SHDI1 as the mackerel code does?
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix a typo for the sh73a0 CPGA code dealing with the IrDA
hardware block on the AG5EVM board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the M3 field offset for the FRQCRA register
in the sh73a0 CPGA. It should be 12, not 8.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
set_irq_type() should only be used for external IRQ pins,
so update the G3EVM board code to remove low level request.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable the MFIS2 interrupt source in the INTCS interrupt
controller included in the sh7372 processor. The priority
field is constantly enabled to let the interrupt through to
both the ARM side and the SH side.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Because ag5evm board setup code uses gpio functions,
ARCH_REQUIRE_GPIOLIB should be set in Kconfig.
Otherwise, the first build with defconfig fails.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The latest rmobile-latest doesn't run on ag5evm because of a
small mistake on initialization.
Though, I don't have any idea to write them smart.
anyway,
On sh73a0, GIC cpu_base is 0xf0000100 but 0xf0001000.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'rmobile-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: Kill off unused !gpio_is_valid() case
ARM: mach-shmobile: sh7372 Enable SDIO IRQs for Mackerel
ARM: mach-shmobile: sh7377 Enable SDIO IRQs
ARM: mach-shmobile: sh7367 Enable SDIO IRQs
ARM: mach-shmobile: sh7372 Enable SDIO IRQs
ARM: mach-shmobile: mackerel: Add touchscreen ST1232 support
ARM: mach-shmobile: ap4eb: SCIF port for earlyprintk when using zboot
ARM: mach-shmobile: mackerel: SCIF port for earlyprintk when using zboot
ARM: mach-shmobile: mackerel: Add support get_cd in CN23
The Card Detect GPIOs used on AP4EVB and Mackerel are
alwayws valid, so kill off the unused !gpio_is_valid()
case.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables interrupt generation for SDIO IRQs
of the SDHI block on the sh7377 aka G4 processor. Use
together with a recent SDHI driver using TMIO_MMC_SDIO_IRQ
and with the MMC_CAP_SDIO_IRQ flag in the board code.
The G4EVM specific SDHI platform data is also updated to
flag SDIO capabilities.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables interrupt generation for SDIO IRQs
of the SDHI block on the sh7367 aka G3 processor. Use
together with a recent SDHI driver using TMIO_MMC_SDIO_IRQ
and with the MMC_CAP_SDIO_IRQ flag in the board code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the interrupt generation for SDIO IRQs
of the sdhi controllers of the SoC. To make sure interrupts
are handled announce the MMC_CAP_SDIO_IRQ capability
on AP4EVB. Tested with a b43-based SDIO wireless card.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Initialise the SCIF serial port to allow earlyprintk
output when using zboot.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Initialise the SCIF serial port to allow earlyprintk
output when using zboot. It is based on a very similar
patched for AP4EB.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove now unused IRQ demux code. All R-Mobile and
SH-Mobile processors should register IRQ demux
handlers during run-time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Break-out GIC specific IRQ demux code from the file
entry-macro-intc.S and register during run-time.
Covers sh73a0.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Break-out INTC specific IRQ demux code from the file
entry-macro-intc.S and register during run-time.
Covers sh7367, sh7377 and sh7372.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use the GIC demux code in asm/hardware/entry-macro-gic.S
on the R-Mobile / SH-Mobile processors.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When CONFIG_ZBOOT_ROM is selected, the resulting zImage file will be small
boot loader and may be burned to rom or flash.
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (416 commits)
ARM: DMA: add support for DMA debugging
ARM: PL011: add DMA burst threshold support for ST variants
ARM: PL011: Add support for transmit DMA
ARM: PL011: Ensure IRQs are disabled in UART interrupt handler
ARM: PL011: Separate hardware FIFO size from TTY FIFO size
ARM: PL011: Allow better handling of vendor data
ARM: PL011: Ensure error flags are clear at startup
ARM: PL011: include revision number in boot-time port printk
ARM: vexpress: add sched_clock() for Versatile Express
ARM i.MX53: Make MX53 EVK bootable
ARM i.MX53: Some bug fix about MX53 MSL code
ARM: 6607/1: sa1100: Update platform device registration
ARM: 6606/1: sa1100: Fix platform device registration
ARM i.MX51: rename IPU irqs
ARM i.MX51: Add ipu clock support
ARM: imx/mx27_3ds: Add PMIC support
ARM: DMA: Replace page_to_dma()/dma_to_page() with pfn_to_dma()/dma_to_pfn()
mx51: fix usb clock support
MX51: Add support for usb host 2
arch/arm/plat-mxc/ehci.c: fix errors/typos
...
fsib_clk will be used when fdiv_clk failed on fsi_hdmi_set_rate.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Prepare the ap4evb board for the MIPI DSI driver transition to support
different register layouts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now, that the MIPI DSI driver implements runtime PM, we don't need anymore to
configure clocks statically in the platform code. This patch also adds a DSITX1
clock definition for sh7372 and attaches PHY clocks to respective devices.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh73a0 has divisor[12] setting as 1/7 on FRQCRA.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add VGA camera support to the Mackerel board
using soc_camera_platform.
The VGA camera module is hooked up using the
8-bit CEU bus, and it is constantly bursting
out frames in fixed video mode setting. The
camera module does not allow any I2C control.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Follow up to pfc-sh73a0.c's pull-up support.
Change GPIO_FN_KEYINx to GPIO_FN_KEYINx_PU.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
