A command like this: "brctl addif br1 eth1" issued as a user gave me
an oops when bridge module wasn't loaded. It's caused by using a dev
pointer before checking for NULL.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 7035560287.
As pointed out by Mark McLoughlin IP_PKTINFO cmsg data is one
post-queueing user, so this optimization is not valid right
now.
Signed-off-by: David S. Miller <davem@davemloft.net>
A separate xmit lock class supports GPRS over a Phonet pipe over a TUN
device (type ARPHRD_NONE).
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also leave some room for more 802.11 types.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ethtool ops to enable and disable GRO. It also
makes GRO depend on RX checksum offload much the same as how TSO
depends on SG support.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the helper skb_gro_receive to merge packets for
GRO. The current method is to allocate a new header skb and then
chain the original packets to its frag_list. This is done to
make it easier to integrate into the existing GSO framework.
In future as GSO is moved into the drivers, we can undo this and
simply chain the original packets together.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the top-level GRO (Generic Receive Offload) infrastructure.
This is pretty similar to LRO except that this is protocol-independent.
Instead of holding packets in an lro_mgr structure, they're now held in
napi_struct.
For drivers that intend to use this, they can set the NETIF_F_GRO bit and
call napi_gro_receive instead of netif_receive_skb or just call netif_rx.
The latter will call napi_receive_skb automatically. When napi_gro_receive
is used, the driver must either call napi_complete/napi_rx_complete, or
call napi_gro_flush in softirq context if the driver uses the primitives
__napi_complete/__napi_rx_complete.
Protocols will set the gro_receive and gro_complete function pointers in
order to participate in this scheme.
In addition to the packet, gro_receive will get a list of currently held
packets. Each packet in the list has a same_flow field which is non-zero
if it is a potential match for the new packet. For each packet that may
match, they also have a flush field which is non-zero if the held packet
must not be merged with the new packet.
Once gro_receive has determined that the new skb matches a held packet,
the held packet may be processed immediately if the new skb cannot be
merged with it. In this case gro_receive should return the pointer to
the existing skb in gro_list. Otherwise the new skb should be merged into
the existing packet and NULL should be returned, unless the new skb makes
it impossible for any further merges to be made (e.g., FIN packet) where
the merged skb should be returned.
Whenever the skb is merged into an existing entry, the gro_receive
function should set NAPI_GRO_CB(skb)->same_flow. Note that if an skb
merely matches an existing entry but can't be merged with it, then
this shouldn't be set.
If gro_receive finds it pointless to hold the new skb for future merging,
it should set NAPI_GRO_CB(skb)->flush.
Held packets will be flushed by napi_gro_flush which is called by
napi_complete and napi_rx_complete.
Currently held packets are stored in a singly liked list just like LRO.
The list is limited to a maximum of 8 entries. In future, this may be
expanded to use a hash table to allow more flows to be held for merging.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows GSO to handle frag_list in a limited way for the
purposes of allowing packets merged by GRO to be refragmented on
output.
Most hardware won't (and aren't expected to) support handling GRO
frag_list packets directly. Therefore we will perform GSO in
software for those cases.
However, for drivers that can support it (such as virtual NICs) we
may not have to segment the packets at all.
Whether the added overhead of GRO/GSO is worthwhile for bridges
and routers when weighed against the benefit of potentially
increasing the MTU within the host is still an open question.
However, for the case of host nodes this is undoubtedly a win.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds limited support for handling frag_list packets in
skb_segment. The intention is to support GRO (Generic Receive Offload)
packets which will be constructed by chaining normal packets using
frag_list.
As such we require all frag_list members terminate on exact MSS
boundaries. This is checked using BUG_ON.
As there should only be one producer in the kernel of such packets,
namely GRO, this requirement should not be difficult to maintain.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few months back a race was discused between the netpoll napi service
path, and the fast path through net_rx_action:
http://kerneltrap.org/mailarchive/linux-netdev/2007/10/16/345470
A patch was submitted for that bug, but I think we missed a case.
Consider the following scenario:
INITIAL STATE
CPU0 has one napi_struct A on its poll_list
CPU1 is calling netpoll_send_skb and needs to call poll_napi on the same
napi_struct A that CPU0 has on its list
CPU0 CPU1
net_rx_action poll_napi
!list_empty (returns true) locks poll_lock for A
poll_one_napi
napi->poll
netif_rx_complete
__napi_complete
(removes A from poll_list)
list_entry(list->next)
In the above scenario, net_rx_action assumes that the per-cpu poll_list is
exclusive to that cpu. netpoll of course violates that, and because the netpoll
path can dequeue from the poll list, its possible for CPU0 to detect a non-empty
list at the top of the while loop in net_rx_action, but have it become empty by
the time it calls list_entry. Since the poll_list isn't surrounded by any other
structure, the returned data from that list_entry call in this situation is
garbage, and any number of crashes can result based on what exactly that garbage
is.
Given that its not fasible for performance reasons to place exclusive locks
arround each cpus poll list to provide that mutal exclusion, I think the best
solution is modify the netpoll path in such a way that we continue to guarantee
that the poll_list for a cpu is in fact exclusive to that cpu. To do this I've
implemented the patch below. It adds an additional bit to the state field in
the napi_struct. When executing napi->poll from the netpoll_path, this bit will
be set. When a driver calls netif_rx_complete, if that bit is set, it will not
remove the napi_struct from the poll_list. That work will be saved for the next
iteration of net_rx_action.
I've tested this and it seems to work well. About the biggest drawback I can
see to it is the fact that it might result in an extra loop through
net_rx_action in the event that the device is actually contended for (i.e. the
netpoll path actually preforms all the needed work no the device, and the call
to net_rx_action winds up doing nothing, except removing the napi_struct from
the poll_list. However I think this is probably a small price to pay, given
that the alternative is a crash.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the last shoot of this series.
After I removing all directly reference of netdev->priv, I am killing
"priv" of "struct net_device" and fixing relative comments/docs.
Anyone will not be allowed to reference netdev->priv directly.
If you want to reference the memory of private data, use netdev_priv()
instead.
If the private data is not allocted when alloc_netdev(), use
netdev->ml_priv to point that memory after you creating that private
data.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
fs/nfsd/nfs4recover.c
Manually fixed above to use new creds API functions, e.g.
nfs4_save_creds().
Signed-off-by: James Morris <jmorris@namei.org>
Since all other gen_estimator functions use bstats and rate_est params
together, and searching for them is optimized now, let's use this also
in gen_estimator_active(). The return type of gen_estimator_active()
is changed to bool, and gen_find_node() parameters to const, btw.
In tcf_act_police_locate() a check for ACT_P_CREATED is added before
calling gen_estimator_active().
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When queuing a skb to sk->sk_receive_queue, we can release its dst,
not anymore needed. Since current cpu did the dst_hold(), refcount is
probably still hot int this cpu caches.
This avoids readers to access the original dst to decrement its
refcount, possibly a long time after packet reception. This should
speedup UDP and RAW receive path.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using one atomic_t per protocol, use a percpu_counter
for "sockets_allocated", to reduce cache line contention on
heavy duty network servers.
Note : We revert commit (248969ae31
net: af_unix can make unix_nr_socks visbile in /proc),
since it is not anymore used after sock_prot_inuse_add() addition
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found that while trying average rate policing, it was possible to
request average rate policing without a rate estimator. This results
in no policing which is harmless but incorrect.
Since policing could be setup in two steps, need to check
in the kernel.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The truesize message check is important enough to make it print "BUG"
to the user console... lets also make it important enough to spit a
backtrace/module list etc so that kerneloops.org can track them.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make
net.core.xfrm_aevent_etime
net.core.xfrm_acq_expires
net.core.xfrm_aevent_rseqth
net.core.xfrm_larval_drop
sysctls per-netns.
For that make net_core_path[] global, register it to prevent two
/proc/net/core antries and change initcall position -- xfrm_init() is called
from fs_initcall, so this one should be fs_initcall at least.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass netns to xfrm_lookup()/__xfrm_lookup(). For that pass netns
to flow_cache_lookup() and resolver callback.
Take it from socket or netdevice. Stub DECnet to init_net.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will filter out the uevent not related to the init_net.
Without this patch if a network device is created in a network
namespace with the same name as one network device belonging to the
initial network namespace (eg. eth0), when the network namespace
will die and the network device will be destroyed, an event will
be sent and catched by the udevd daemon. That will result to have
the real network device to be shutdown because the udevd/uevent are
not namespace aware.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since pskb_expand_head creates copy of the shared area we
cannot keep any frag ptr past de-cloning. This fixes the
tcpdump recvfrom -EFAULT problem.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This caused me to get repeatably:
tcpdump: pcap_loop: recvfrom: Bad address
Happens occassionally when I tcpdump my for-looped test xfers:
while [ : ]; do echo -n "$(date '+%s.%N') "; ./sendfile; sleep 20; done
Rest of the relevant commands:
ethtool -K eth0 tso off
tc qdisc add dev eth0 root netem drop 4%
tcpdump -n -s0 -i eth0 -w sacklog.all
Running net-next under kvm, connection goes to the same host
(basically just out of kvm). The connection itself works ok
and data gets sent without corruption even with a large
number of tests while tcpdump fails usually within less than
5 tests.
Whether it only happens because of this change or not, I
don't know for sure but it's the only thing with which
I've seen that error. The non-cloned variant works w/o it
for much longer time. I'm yet to debug where the error
actually comes from.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
During SACK processing, most of the benefits of TSO are eaten by
the SACK blocks that one-by-one fragment SKBs to MSS sized chunks.
Then we're in problems when cleanup work for them has to be done
when a large cumulative ACK comes. Try to return back to pre-split
state already while more and more SACK info gets discovered by
combining newly discovered SACK areas with the previous skb if
that's SACKed as well.
This approach has a number of benefits:
1) The processing overhead is spread more equally over the RTT
2) Write queue has less skbs to process (affect everything
which has to walk in the queue past the sacked areas)
3) Write queue is consistent whole the time, so no other parts
of TCP has to be aware of this (this was not the case with
some other approach that was, well, quite intrusive all
around).
4) Clean_rtx_queue can release most of the pages using single
put_page instead of previous PAGE_SIZE/mss+1 calls
In case a hole is fully filled by the new SACK block, we attempt
to combine the next skb too which allows construction of skbs
that are even larger than what tso split them to and it handles
hole per on every nth patterns that often occur during slow start
overshoot pretty nicely. Though this to be really useful also
a retransmission would have to get lost since cumulative ACKs
advance one hole at a time in the most typical case.
TODO: handle upwards only merging. That should be rather easy
when segment is fully sacked but I'm leaving that as future
work item (it won't make very large difference anyway since
this current approach already covers quite a lot of normal
cases).
I was earlier thinking of some sophisticated way of tracking
timestamps of the first and the last segment but later on
realized that it won't be that necessary at all to store the
timestamp of the last segment. The cases that can occur are
basically either:
1) ambiguous => no sensible measurement can be taken anyway
2) non-ambiguous is due to reordering => having the timestamp
of the last segment there is just skewing things more off
than does some good since the ack got triggered by one of
the holes (besides some substle issues that would make
determining right hole/skb even harder problem). Anyway,
it has nothing to do with this change then.
I choose to route some abnormal looking cases with goto noop,
some could be handled differently (eg., by stopping the
walking at that skb but again). In general, they either
shouldn't happen at all or are rare enough to make no difference
in practice.
In theory this change (as whole) could cause some macroscale
regression (global) because of cache misses that are taken over
the round-trip time but it gets very likely better because of much
less (local) cache misses per other write queue walkers and the
big recovery clearing cumulative ack.
Worth to note that these benefits would be very easy to get also
without TSO/GSO being on as long as the data is in pages so that
we can merge them. Currently I won't let that happen because
DSACK splitting at fragment that would mess up pcounts due to
sk_can_gso in tcp_set_skb_tso_segs. Once DSACKs fragments gets
avoided, we have some conditions that can be made less strict.
TODO: I will probably have to convert the excessive pointer
passing to struct sacktag_state... :-)
My testing revealed that considerable amount of skbs couldn't
be shifted because they were cloned (most likely still awaiting
tx reclaim)...
[The rest is considering future work instead since I got
repeatably EFAULT to tcpdump's recvfrom when I added
pskb_expand_head to deal with clones, so I separated that
into another, later patch]
...To counter that, I gave up on the fifth advantage:
5) When growing previous SACK block, less allocs for new skbs
are done, basically a new alloc is needed only when new hole
is detected and when the previous skb runs out of frags space
...which now only happens of if reclaim is fast enough to dispose
the clone before the SACK block comes in (the window is RTT long),
otherwise we'll have to alloc some.
With clones being handled I got these numbers (will be somewhat
worse without that), taken with fine-grained mibs:
TCPSackShifted 398
TCPSackMerged 877
TCPSackShiftFallback 320
TCPSACKCOLLAPSEFALLBACKGSO 0
TCPSACKCOLLAPSEFALLBACKSKBBITS 0
TCPSACKCOLLAPSEFALLBACKSKBDATA 0
TCPSACKCOLLAPSEFALLBACKBELOW 0
TCPSACKCOLLAPSEFALLBACKFIRST 1
TCPSACKCOLLAPSEFALLBACKPREVBITS 318
TCPSACKCOLLAPSEFALLBACKMSS 1
TCPSACKCOLLAPSEFALLBACKNOHEAD 0
TCPSACKCOLLAPSEFALLBACKSHIFT 0
TCPSACKCOLLAPSENOOPSEQ 0
TCPSACKCOLLAPSENOOPSMALLPCOUNT 0
TCPSACKCOLLAPSENOOPSMALLLEN 0
TCPSACKCOLLAPSEHOLE 12
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
gen_kill_estimator() linear lists lookups are very slow, and e.g. while
deleting a large number of HTB classes soft lockups were reported. Here
is another try to fix this problem: this time internally, with rbtree,
so similarly to Jamal's hashing idea IIRC. (Looking for next hits could
be still optimized, but it's really fast as it is.)
Reported-by: Badalian Vyacheslav <slavon@bigtelecom.ru>
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the slub allocator is used, kmem_cache_create() may merge two or more
kmem_cache's into one but the cache name pointer is not updated and
kmem_cache_name() is no longer guaranteed to return the pointer passed
to the former function. This patch stores the kmalloc'ed pointers in the
corresponding request_sock_ops and timewait_sock_ops structures.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SKF_AD_NLATTR allows us to find the first matching attribute in a
stream of netlink attributes from one offset to the end of the
netlink message. This is not suitable to look for a specific
matching inside a set of nested attributes.
For example, in ctnetlink messages, if we look for the CTA_V6_SRC
attribute in a message that talks about an IPv4 connection,
SKF_AD_NLATTR returns the offset of CTA_STATUS which has the same
value of CTA_V6_SRC but outside the nest. To differenciate
CTA_STATUS and CTA_V6_SRC, we would have to make assumptions on the
size of the attribute and the usual offset, resulting in horrible
BSF code.
This patch adds SKF_AD_NLATTR_NEST, which is a variant of
SKF_AD_NLATTR, that looks for an attribute inside the limits of
a nested attributes, but not further.
This patch validates that we have enough room to look for the
nested attributes - based on a suggestion from Patrick McHardy.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the network device ops get_stats call to be immutable, the handling
of the default internal network device stats block has to be changed. Add a new
helper function which replaces the old use of internal_get_stats.
Note: change return code to make it clear that the caller should not
go changing the returned statistics.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the network device internal API to move adminstrative
operations out of the network device structure and into a separate structure.
This patch involves some hackery to maintain compatablity between the
new and old model, so all 300+ drivers don't have to be changed at once.
For drivers that aren't converted yet, the netdevice_ops virt function list
still resides in the net_device structure. For old protocols, the new
net_device_ops are copied out to the old net_device pointers.
After the transistion is completed the nag message can be changed to
an WARN_ON, and the compatiablity code can be made configurable.
Some function pointers aren't moved:
* destructor can't be in net_device_ops because
it may need to be referenced after the module is unloaded.
* neighbor setup is manipulated in a couple of places that need special
consideration
* hard_start_xmit is in the fast path for transmit.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first argument to csum_partial is const void *
casts to char/u8 * are not necessary
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converting /proc/net/protocols to be namespace aware is quite easy
and permits us to use sock_prot_inuse_get().
This provides seperate counters for each protocol. For example
we can really count TCPv6 sockets and TCPv4 sockets, while previously,
we had the same value, and this value was not namespace aware.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As number of TX queues in unrelated to number of CPU's we remove this test
and just make sure nxtq never gets exceeded.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike ifconfig, iproute doesn't report an error when setting
an interface up fails:
(example: put wireless network mac80211 interface into repeater mode
with iwconfig but do not set a peer MAC address, it should fail with
-ENOLINK)
without patch:
# ip link set wlan0 up ; echo $?
0
#
with patch:
# ip link set wlan0 up ; echo $?
RTNETLINK answers: Link has been severed
2
#
Propagate the return value from dev_change_flags() to fix this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Technically, patch changes format for modules, but I think nobody cares.
-86dd :ipv6:ipv6_rcv+0x0
+86dd ipv6_rcv+0x0/0x400 [ipv6]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RCU was added to UDP lookups, using a fast infrastructure :
- sockets kmem_cache use SLAB_DESTROY_BY_RCU and dont pay the
price of call_rcu() at freeing time.
- hlist_nulls permits to use few memory barriers.
This patch uses same infrastructure for TCP/DCCP established
and timewait sockets.
Thanks to SLAB_DESTROY_BY_RCU, no slowdown for applications
using short lived TCP connections. A followup patch, converting
rwlocks to spinlocks will even speedup this case.
__inet_lookup_established() is pretty fast now we dont have to
dirty a contended cache line (read_lock/read_unlock)
Only established and timewait hashtable are converted to RCU
(bind table and listen table are still using traditional locking)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the next page of the scm recursion story (the commit
f8d570a4 net: Fix recursive descent in __scm_destroy()).
In function scm_fp_dup(), the INIT_LIST_HEAD(&fpl->list) of newly
created fpl is done *before* the subsequent memcpy from the old
structure and thus the freshly initialized list is overwritten.
But that's OK, since this initialization is not required at all,
since the fpl->list is list_add-ed at the destruction time in any
case (and is unused in other code), so I propose to drop both
initializations, rather than moving it after the memcpy.
Please, correct me if I miss something significant.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During tbench/oprofile sessions, I found that dst_release() was in third position.
CPU: Core 2, speed 2999.68 MHz (estimated)
Counted CPU_CLK_UNHALTED events (Clock cycles when not halted) with a unit mask of 0x00 (Unhalted core cycles) count 100000
samples % symbol name
483726 9.0185 __copy_user_zeroing_intel
191466 3.5697 __copy_user_intel
185475 3.4580 dst_release
175114 3.2648 ip_queue_xmit
153447 2.8608 tcp_sendmsg
108775 2.0280 tcp_recvmsg
102659 1.9140 sysenter_past_esp
101450 1.8914 tcp_current_mss
95067 1.7724 __copy_from_user_ll
86531 1.6133 tcp_transmit_skb
Of course, all CPUS fight on the dst_entry associated with 127.0.0.1
Instead of first checking the refcount value, then decrement it,
we use atomic_dec_return() to help CPU to make the right memory transaction
(ie getting the cache line in exclusive mode)
dst_release() is now at the fifth position, and tbench a litle bit faster ;)
CPU: Core 2, speed 3000.1 MHz (estimated)
Counted CPU_CLK_UNHALTED events (Clock cycles when not halted) with a unit mask of 0x00 (Unhalted core cycles) count 100000
samples % symbol name
647107 8.8072 __copy_user_zeroing_intel
258840 3.5229 ip_queue_xmit
258302 3.5155 __copy_user_intel
209629 2.8531 tcp_sendmsg
165632 2.2543 dst_release
149232 2.0311 tcp_current_mss
147821 2.0119 tcp_recvmsg
137893 1.8767 sysenter_past_esp
127473 1.7349 __copy_from_user_ll
121308 1.6510 ip_finish_output
118510 1.6129 tcp_transmit_skb
109295 1.4875 tcp_v4_rcv
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix this warning:
net/bluetooth/af_bluetooth.c:60: warning: ‘bt_key_strings’ defined but not used
net/bluetooth/af_bluetooth.c:71: warning: ‘bt_slock_key_strings’ defined but not used
this is a lockdep macro problem in the !LOCKDEP case.
We cannot convert it to an inline because the macro works on multiple types,
but we can mark the parameter used.
[ also clean up a misaligned tab in sock_lock_init_class_and_name() ]
[ also remove #ifdefs from around af_family_clock_key strings - which
were certainly added to get rid of the ugly build warnings. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
security/keys/internal.h
security/keys/process_keys.c
security/keys/request_key.c
Fixed conflicts above by using the non 'tsk' versions.
Signed-off-by: James Morris <jmorris@namei.org>
Wrap current->cred and a few other accessors to hide their actual
implementation.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Separate the task security context from task_struct. At this point, the
security data is temporarily embedded in the task_struct with two pointers
pointing to it.
Note that the Alpha arch is altered as it refers to (E)UID and (E)GID in
entry.S via asm-offsets.
With comment fixes Signed-off-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: netdev@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
Using read_pnet() and write_pnet() in neighbour code ease the reading
of code.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
->pde isn't actually needed, since name is stashed in ->id.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since skb_reset_tail_pointer() reads skb->data, we need to set
skb->data before calling skb_reset_tail_pointer(). This was causing
spurious skb_over_panic()s from skb_put() being called on a recycled
skb that had its skb->tail set to beyond where it should have been.
Bug report from Peter van Valderen <linux@ddcrew.com>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing pktgen, I found that sometimes my configurations from
previous runs would be left over, particularly when going from a test
with 8 threads down to a test with 4 threads.
This adds new functionality to pktgen where you can call
pgset "reset"
and it will be just like you just insmod'ed pktgen again.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was recently hunting a bug that occurred in network namespace
cleanup. In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present. Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.
Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init(). This guarantes
that the loopback device is the first device registered and
the last network device to go away.
But do it carefully so we register the loopback device after
we clear dev_boot_phase.
Signed-off-by: Eric W. Biederman <ebiederm@maxwell.aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to setup the network namespace state before we register
the notifier. Otherwise if a network device is already registered
we get a nasty NULL pointer dereference.
Signed-off-by: Eric W. Biederman <ebiederm@maxwell.aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's called from __init code only. And__devinit in generic networking code
is pretty strange :^)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__scm_destroy() walks the list of file descriptors in the scm_fp_list
pointed to by the scm_cookie argument.
Those, in turn, can close sockets and invoke __scm_destroy() again.
There is nothing which limits how deeply this can occur.
The idea for how to fix this is from Linus. Basically, we do all of
the fput()s at the top level by collecting all of the scm_fp_list
objects hit by an fput(). Inside of the initial __scm_destroy() we
keep running the list until it is empty.
Signed-off-by: David S. Miller <davem@davemloft.net>
I have been tracking for a while a case where when the
network namespace exits the cleanup gets stck in an
endless precessess of:
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
It turns out that if you listen on a multicast address an unsubscribe
packet is sent when the network device goes down. If you shutdown
the network namespace without carefully cleaning up this can trigger
the unsubscribe packet to be sent over the loopback interface while
the network namespace is going down.
All of which is fine except when we drop the packet and forget to
free it leaking the skb and the dst entry attached to. As it
turns out the dst entry hold a reference to the idev which holds
the dev and keeps everything from being cleaned up. Yuck!
By fixing my earlier thinko and add the needed kfree_skb and everything
cleans up beautifully.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was recently hunting a bug that occurred in network namespace
cleanup. In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present. Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.
Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init(). This guarantes
that the loopback device is the first device registered and
the last network device to go away.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When physical devices are inside of network namespace and that
network namespace terminates we can not make them go away. We
have to keep them and moving them to the initial network namespace
is the best we can do.
For virtual devices left in a network namespace that is exiting
we have no need to preserve them and we now have the infrastructure
that allows us to delete them. So delete virtual devices when we
exit a network namespace. Keeping the necessary user space clean up
after a network namespace exits much more tractable.
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed a contention on udp_memory_allocated on regular UDP applications.
While tcp_memory_allocated is seldom used, it appears each incoming UDP frame
is currently touching udp_memory_allocated when queued, and when received by
application.
One possible solution is to use sk_mem_reclaim_partial() instead of
sk_mem_reclaim(), so that we keep a small reserve (less than one page)
of memory for each UDP socket.
We did something very similar on TCP side in commit
9993e7d313
([TCP]: Do not purge sk_forward_alloc entirely in tcp_delack_timer())
A more complex solution would need to convert prot->memory_allocated to
use a percpu_counter with batches of 64 or 128 pages.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The changes to deliver hardware accelerated VLAN packets to packet
sockets (commit bc1d0411) caused a warning for non-NAPI drivers.
The __vlan_hwaccel_rx() function is called directly from the drivers
RX function, for non-NAPI drivers that means its still in RX IRQ
context:
[ 27.779463] ------------[ cut here ]------------
[ 27.779509] WARNING: at kernel/softirq.c:136 local_bh_enable+0x37/0x81()
...
[ 27.782520] [<c0264755>] netif_nit_deliver+0x5b/0x75
[ 27.782590] [<c02bba83>] __vlan_hwaccel_rx+0x79/0x162
[ 27.782664] [<f8851c1d>] atl1_intr+0x9a9/0xa7c [atl1]
[ 27.782738] [<c0155b17>] handle_IRQ_event+0x23/0x51
[ 27.782808] [<c015692e>] handle_edge_irq+0xc2/0x102
[ 27.782878] [<c0105fd5>] do_IRQ+0x4d/0x64
Split hardware accelerated VLAN reception into two parts to fix this:
- __vlan_hwaccel_rx just stores the VLAN TCI and performs the VLAN
device lookup, then calls netif_receive_skb()/netif_rx()
- vlan_hwaccel_do_receive(), which is invoked by netif_receive_skb()
in softirq context, performs the real reception and delivery to
packet sockets.
Reported-and-tested-by: Ramon Casellas <ramon.casellas@cttc.es>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I want to compile out proc_* and sysctl_* handlers totally and
stub them to NULL depending on config options, however usage of &
will prevent this, since taking adress of NULL pointer will break
compilation.
So, drop & in front of every ->proc_handler and every ->strategy
handler, it was never needed in fact.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gets about 1.25% back on tbench regression.
My change to NAPI for multiqueue support changed the time limit on
network receive processing. Under sustained loads like tbench, this
can cause the receiver to reschedule prematurely.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 04a4bb55bc ("net: add
skb_recycle_check() to enable netdriver skb recycling") added a
method for network drivers to recycle skbuffs, but while use of
this mechanism was documented in the commit message, it should
really have been added as a docbook comment as well -- this
patch does that.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wireless HW without any dedicated queues for aggregation
do not need the ampdu_queues mechanism present right now
in mac80211. Since mac80211 is still incomplete wrt TX MQ
changes, do not allow aggregation sessions for drivers that
set ampdu_queues.
This is only an interim hack until Intel fixes the requeue issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
netns ops which are registered with register_pernet_gen_device() are
shutdown strictly before those which are registered with
register_pernet_subsys(). Sometimes this leads to opposite (read: buggy)
shutdown ordering between two modules.
Add register_pernet_gen_subsys()/unregister_pernet_gen_subsys() for modules
which aren't elite enough for entry in struct net, and which can't use
register_pernet_gen_device(). PPTP conntracking module is such one.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Goals are :
1) Optimizing handling of incoming Unicast UDP frames, so that no memory
writes should happen in the fast path.
Note: Multicasts and broadcasts still will need to take a lock,
because doing a full lockless lookup in this case is difficult.
2) No expensive operations in the socket bind/unhash phases :
- No expensive synchronize_rcu() calls.
- No added rcu_head in socket structure, increasing memory needs,
but more important, forcing us to use call_rcu() calls,
that have the bad property of making sockets structure cold.
(rcu grace period between socket freeing and its potential reuse
make this socket being cold in CPU cache).
David did a previous patch using call_rcu() and noticed a 20%
impact on TCP connection rates.
Quoting Cristopher Lameter :
"Right. That results in cacheline cooldown. You'd want to recycle
the object as they are cache hot on a per cpu basis. That is screwed
up by the delayed regular rcu processing. We have seen multiple
regressions due to cacheline cooldown.
The only choice in cacheline hot sensitive areas is to deal with the
complexity that comes with SLAB_DESTROY_BY_RCU or give up on RCU."
- Because udp sockets are allocated from dedicated kmem_cache,
use of SLAB_DESTROY_BY_RCU can help here.
Theory of operation :
---------------------
As the lookup is lockfree (using rcu_read_lock()/rcu_read_unlock()),
special attention must be taken by readers and writers.
Use of SLAB_DESTROY_BY_RCU is tricky too, because a socket can be freed,
reused, inserted in a different chain or in worst case in the same chain
while readers could do lookups in the same time.
In order to avoid loops, a reader must check each socket found in a chain
really belongs to the chain the reader was traversing. If it finds a
mismatch, lookup must start again at the begining. This *restart* loop
is the reason we had to use rdlock for the multicast case, because
we dont want to send same message several times to the same socket.
We use RCU only for fast path.
Thus, /proc/net/udp still takes spinlocks.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
call_rcu() will unconditionally rewrite RCU head anyway.
Applies to
struct neigh_parms
struct neigh_table
struct net
struct cipso_v4_doi
struct in_ifaddr
struct in_device
rt->u.dst
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when testing the new pktgen module with multiple queues and ixgbe with:
pgset "flag QUEUE_MAP_CPU"
I found that I was getting errors in dmesg like:
pktgen: WARNING: QUEUE_MAP_CPU disabled because CPU count (8) exceeds number
<4>pktgen: WARNING: of tx queues (8) on eth15
you'll note, 8 really doesn't exceed 8.
This patch seemed to fix the logic errors and also the attempts at
limiting line length in printk (which didn't work anyway)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make testing of the network namespace simpler allow
the network namespace code and the sysfs code to be
compiled and run at the same time. To do this only
virtual devices are allowed in the additional network
namespaces and those virtual devices are not placed
in the kobject tree.
Since virtual devices don't actually do anything interesting
hardware wise that needs device management there should
be no loss in keeping them out of the kobject tree and
by implication sysfs. The gain in ease of testing
and code coverage should be significant.
Changelog:
v2: As pointed out by Benjamin Thery it only makes sense to call
device_rename in the initial network namespace for now.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Tested-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
My change
commit e2a6b85247
net: Enable TSO if supported by at least one device
didn't do what was intended because the netdev_compute_features
function was designed for conjunctions. So what happened was that
it would simply take the TSO status of the last constituent device.
This patch extends it to support both conjunctions and disjunctions
under the new name of netdev_increment_features.
It also adds a new function netdev_fix_features which does the
sanity checking that usually occurs upon registration. This ensures
that the computation doesn't result in an illegal combination
since this checking is absent when the change is initiated via
ethtool.
The two users of netdev_compute_features have been converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If changename notifier returns an error code, it gets incorrectly
cleared during rollback so the error is never returned to the user.
Found while testing similar code for MTU changes.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some code here depends on CONFIG_KMOD to not try to load
protocol modules or similar, replace by CONFIG_MODULES
where more than just request_module depends on CONFIG_KMOD
and and also use try_then_request_module in ebtables.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up the various different email addresses of mine listed in the code
to a single current and valid address. As Dave says his network merges
for 2.6.28 are now done this seems a good point to send them in where
they won't risk disrupting real changes.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seems that skb goes into void unless something magic happened
in pskb_expand_head in case of failure.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unwind loop iterates down to -1 instead of stopping at 0 and ends up
accessing ->frags[-1].
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conntrack code will use it for
a) removing expectations and helpers when corresponding module is removed, and
b) removing conntracks when L3 protocol conntrack module is removed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Benjamin Thery tracked down a bug that explains many instances
of the error
unregister_netdevice: waiting for %s to become free. Usage count = %d
It turns out that netdev_run_todo can dead-lock with itself if
a second instance of it is run in a thread that will then free
a reference to the device waited on by the first instance.
The problem is really quite silly. We were trying to create
parallelism where none was required. As netdev_run_todo always
follows a RTNL section, and that todo tasks can only be added
with the RTNL held, by definition you should only need to wait
for the very ones that you've added and be done with it.
There is no need for a second mutex or spinlock.
This is exactly what the following patch does.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer <hawk@comx.dk> reported a bug when setting a VLAN
device down that is in promiscous mode:
When the VLAN device is set down, the promiscous count on the real
device is decremented by one by vlan_dev_stop(). When removing the
promiscous flag from the VLAN device afterwards, the promiscous
count on the real device is decremented a second time by the
vlan_change_rx_flags() callback.
The root cause for this is that the ->change_rx_flags() callback is
invoked while the device is down. The synchronization is meant to mirror
the behaviour of the ->set_rx_mode callbacks, meaning the ->open function
is responsible for doing a full sync on open, the ->close() function is
responsible for doing full cleanup on ->stop() and ->change_rx_flags()
is meant to do incremental changes while the device is UP.
Only invoke ->change_rx_flags() while the device is UP to provide the
intended behaviour.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some packet-split receive hooks.
For one this allows to do NUMA node affine page allocs. Later on these
hooks will be extended to do emergency reserve allocations for
fragments.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrap calling sk->sk_backlog_rcv() in a function. This will allow extending the
generic sk_backlog_rcv behaviour.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the caller of pskb_expand_head specifies a negative nhead
we'll silently overwrite other people's memory. This patch
makes it BUG instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds skb_recycle_check(), which can be used by a network
driver after transmitting an skb to check whether this skb can be
recycled as a receive buffer.
skb_recycle_check() checks that the skb is not shared or cloned, and
that it is linear and its head portion large enough (as determined by
the driver) to be recycled as a receive buffer. If these conditions
are met, it does any necessary reference count dropping and cleans
up the skbuff as if it just came from __alloc_skb().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more docbook comments to network device functions and cleanup
the comments.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_change_name and netdev_drivername should use const char on
parameters that are read-only input values. The strcpy to newname is
not needed since newname is not used later in function.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the potentially allocated ifalias when the (new) given alias is empty.
E.g. when setting
echo "" > /sys/class/net/eth0/ifalias
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for keeping an additional character alias
associated with an network interface. This is useful for maintaining
the SNMP ifAlias value which is a user defined value. Routers use this
to hold information like which circuit or line it is connected to. It
is just an arbitrary text label on the network device.
There are two exposed interfaces with this patch, the value can be
read/written either via netlink or sysfs.
This could be maintained just by the snmp daemon, but it is more
generally useful for other management tools, and the kernel is good
place to act as an agreed upon interface to store it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently simple_tx_hash is hashing inside of udp fragments. As a result
packets are getting getting sent to all queues when they shouldn't be.
This causes a serious performance regression which can be seen by sending
UDP frames larger than mtu on multiqueue devices. This change will make
it so that fragments are hashed only as IP datagrams w/o any protocol
information.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dst garbage collector dst_gc_task() may not be scheduled as we
expect it to be in __dst_free().
Indeed, when the dst_gc_timer was replaced by the delayed_work
dst_gc_work, the mod_timer() call used to schedule the garbage
collector at an earlier date was replaced by a schedule_delayed_work()
(see commit 86bba269d0).
But, the behaviour of mod_timer() and schedule_delayed_work() is
different in the way they handle the delay.
mod_timer() stops the timer and re-arm it with the new given delay,
whereas schedule_delayed_work() only check if the work is already
queued in the workqueue (and queue it (with delay) if it is not)
BUT it does NOT take into account the new delay (even if the new delay
is earlier in time).
schedule_delayed_work() returns 0 if it didn't queue the work,
but we don't check the return code in __dst_free().
If I understand the code in __dst_free() correctly, we want dst_gc_task
to be queued after DST_GC_INC jiffies if we pass the test (and not in
some undetermined time in the future), so I think we should add a call
to cancel_delayed_work() before schedule_delayed_work(). Patch below.
Or we should at least test the return code of schedule_delayed_work(),
and reset the values of dst_garbage.timer_inc and dst_garbage.timer_expires
back to their former values if schedule_delayed_work() failed.
Otherwise the subsequent calls to __dst_free will test the wrong values
and assume wrong thing about when the garbage collector is supposed to
be scheduled.
dst_gc_task() also calls schedule_delayed_work() without checking
its return code (or calling cancel_scheduled_work() first), but it
should fine there: dst_gc_task is the routine of the delayed_work, so
no dst_gc_work should be pending in the queue when it's running.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it stands users of netdev_compute_features (e.g., bridges/bonding)
will only enable TSO if all consituent devices support it. This
is unnecessarily pessimistic since even on devices that do not
support hardware TSO and SG, emulated TSO still performs to a par
with TSO off.
This patch enables TSO if at least on constituent device supports
it in hardware.
The direct beneficiaries will be virtualisation that uses bridging
since this means that TSO will always be enabled for communication
from the host to the guests.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_tx_action() can skip __QDISC_STATE_SCHED bit clearing while qdisc
is neither ran nor rescheduled, which may cause endless loop in
dev_deactivate().
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dev_deactivate() is trying to quiesce the queue, it
is theoretically possible for another cpu to livelock
trying to process that queue. This happens because
dev_deactivate() grabs the queue spinlock as it checks
the queue state, whereas net_tx_action() does a trylock
and reschedules the qdisc if it hits the lock.
This breaks the livelock by adding a check on
__QDISC_STATE_DEACTIVATED to net_tx_action() when
the trylock fails.
Based upon feedback from Herbert Xu and Jarek Poplawski.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d4766692e7.
qdisc_destroy() now runs in RTNL fully again, so this
change is no longer needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change handling of the __QDISC_STATE_SCHED flag in net_tx_action() to
enable proper control in dev_deactivate(). Now, if this flag is seen
as unset under root_lock means a qdisc can't be netif_scheduled.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new state lets dev_deactivate() mark a qdisc as having been
deactivated.
dev_queue_xmit() and ing_filter() check for this bit and do not
try to process the qdisc if the bit is set.
dev_deactivate() polls the qdisc after setting the bit, waiting
for both __QDISC_STATE_RUNNING and __QDISC_STATE_SCHED to clear.
This isn't perfect yet, but subsequent changesets will make it so.
This part is just one piece of the puzzle.
Signed-off-by: David S. Miller <davem@davemloft.net>
There's an skb_copy_datagram_iovec() to copy out of a paged skb, but
nothing the other way around (because we don't do that).
We want to allocate big skbs in tun.c, so let's add the function.
It's a carbon copy of skb_copy_datagram_iovec() with enough changes to
be annoying.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gso_segment didn't preserve some attributes in the original skb
such as the netfilter fields. This was harmless until they were used
which is the case for packets going through lo.
This patch makes it call __copy_skb_header which also picks up some
other missing attributes.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
gen_kill_estimator() required rtnl_lock() protection, but since it is
moved to an RCU callback __qdisc_destroy() let's use est_lock instead.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the new multi-queue transmit code, it is possible to accidentally
make pktgen pick a non-existing tx queue simply by using a stale
script to drive pktgen. Access to this non-existing tx queue will
then trigger a bad memory access and kill the machine.
For example, setting "queue_map_max 2" will cause my machine to die
when accessing a garbage spinlock in the non-existing tx queue:
BUG: spinlock bad magic on CPU#0, kpktgend_0/564
lock: ffff88001ddf6718, .magic: ffffffff, .owner: /-1, .owner_cpu: 0
Pid: 564, comm: kpktgend_0 Not tainted 2.6.27-rc3 #35
Call Trace:
[<ffffffff803a1228>] spin_bug+0xa4/0xac
[<ffffffff803a1253>] _raw_spin_lock+0x23/0x123
[<ffffffff8055b06f>] _spin_lock_bh+0x17/0x1b
[<ffffffff804cb57d>] pktgen_thread_worker+0xa97/0x1002
[<ffffffff8022874d>] ? finish_task_switch+0x38/0x97
[<ffffffff80242077>] ? autoremove_wake_function+0x0/0x36
[<ffffffff80242077>] ? autoremove_wake_function+0x0/0x36
[<ffffffff804caae6>] ? pktgen_thread_worker+0x0/0x1002
[<ffffffff80241a40>] kthread+0x44/0x6d
[<ffffffff8020c399>] child_rip+0xa/0x11
[<ffffffff802419fc>] ? kthread+0x0/0x6d
[<ffffffff8020c38f>] ? child_rip+0x0/0x11
The attached patch adds some sanity checking to prevent
these sorts of configuration errors.
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sofar far pktgen have had a restriction to only use one device per kernel
thread. With the new multiqueue architecture this is no longer adequate.
The patch below is an effort to remove this by in pktgen configuration
adding a tag to the device name a la eth0@0 etc. The tag is used for
usual device config just as before. Also a new flag is introduced to mirror
queue_map with sending threads smp_processor_id() QUEUE_MAP_CPU.
An example: We use 4 CPU's to send to one 10g interface (eth0)
and we use the new tagging to send a mix of packet sizes, 64, 576 and
1500 bytes. Also we use TX queues according to smp_processor_id()
PGDEV=/proc/net/pktgen/kpktgend_0
pgset "add_device eth0@0"
PGDEV=/proc/net/pktgen/kpktgend_1
pgset "add_device eth0@1"
PGDEV=/proc/net/pktgen/kpktgend_2
pgset "add_device eth0@2"
PGDEV=/proc/net/pktgen/kpktgend_3
pgset "add_device eth0@3"
....
PGDEV=/proc/net/pktgen/eth0@0
pgset "pkt_size 64"
pgset "flag QUEUE_MAP_CPU"
PGDEV=/proc/net/pktgen/eth0@1
pgset "pkt_size 572"
pgset "flag QUEUE_MAP_CPU"
PGDEV=/proc/net/pktgen/eth0@2
pgset "pkt_size 1496"
PGDEV=/proc/net/pktgen/eth0@3
pgset "pkt_size 1496"
pgset "flag QUEUE_MAP_CPU"
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a packet_type specifies an active slave to bonding and not just any
interface, allow it to receive frames that came in on that interface.
Signed-off-by: Joe Eykholt <jre@nuovasystems.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Allow a packet_type that specifies the exact device to receive
even on an inactive bonding slave devices. This is important for some
L2 protocols such as LLDP and FCoE. This can eventually be used
for the bonding special cases as well.
Signed-off-by: Joe Eykholt <jre@nuovasystems.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Otherwise subsequent changes need multiple return values.
Signed-off-by: Joe Eykholt <jre@nuovasystems.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dst_mac_count and src_mac_count patch from Eneas Hunguana
We have sent one mac address to much.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Random flow generation has not worked. This fixes it.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy <kaber@trash.net> noticed that it would be nice to
handle NET_XMIT_BYPASS by NET_XMIT_SUCCESS with an internal qdisc flag
__NET_XMIT_BYPASS and to remove the mapping from dev_queue_xmit().
David Miller <davem@davemloft.net> spotted a serious bug in the first
version of this patch.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the overhead of atomic increment/decrement on each received packet.
This helps performance of non-NAPI devices (like loopback).
Use cleanup function to walk queue on each cpu and clean out any
left over packets.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a netdevice does not support hardware GSO, allowing the stack to
use GSO anyway and then splitting the GSO skb into MSS-sized pieces
as it is handed to the netdevice for transmitting is likely still
a win as far as throughput and/or CPU usage are concerned, since it
reduces the number of trips through the output path.
This patch enables the use of GSO on any netdevice that supports SG.
If a GSO skb is then sent to a netdevice that supports SG but does not
support hardware GSO, net/core/dev.c:dev_hard_start_xmit() will take
care of doing the necessary GSO segmentation in software.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When pneigh entries exist, but the user's read buffer isn't sufficient to
hold them all, one of the pneigh entries will be missing from the results.
In neigh_get_idx_any, the number of elements which neigh_get_idx
encountered is not correctly subtracted from the position number before
the call to pneigh_get_idx. neigh_get_idx reduces the position by 1 for
each call to neigh_get_next, but it does not reduce it by one for the
first element (neigh_get_first). The patch alters the neigh_get_idx and
pneigh_get_idx functions to subtract one from pos, for the first element,
when pos is non-zero.
Signed-off-by: Chris Larson <clarson@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
neigh_seq_next won't be called both with *pos > 0 && v ==
SEQ_START_TOKEN, so there's no point calling neigh_get_idx when we're
on the start token, just call neigh_get_first directly.
Signed-off-by: Chris Larson <clarson@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a bug report by Jeff Kirsher.
Don't use qdisc_root_lock() in these cases as the root
qdisc could have been changed, and we'd thus lock the
wrong object.
Tested by Emil S Tantilov who confirms that this seems
to fix the problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for multiple TX queues were added, the
netif_tx_lock() routines we converted to iterate over
all TX queues and grab each queue's spinlock.
This causes heartburn for lockdep and it's not a healthy
thing to do with lots of TX queues anyways.
So modify this to use a top-level lock and a "frozen"
state for the individual TX queues.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug report from Steven Jan Springl:
Issuing the following command causes a kernel oops:
tc qdisc add dev eth0 handle ffff: ingress
The problem mostly stems from all of the special case handling of
ingress qdiscs.
So, to fix this, do the grafting operation the same way we do for TX
qdiscs. Which means that dev_activate() and dev_deactivate() now do
the "qdisc_sleeping <--> qdisc" transitions on dev->rx_queue too.
Future simplifications are possible now, mainly because it is
impossible for dev_queue->{qdisc,qdisc_sleeping} to be NULL. There
are NULL checks all over to handle the ingress qdisc special case
that used to exist before this commit.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: fix ip_rt_frag_needed rt_is_expired
netfilter: nf_conntrack_extend: avoid unnecessary "ct->ext" dereferences
netfilter: fix double-free and use-after free
netfilter: arptables in netns for real
netfilter: ip{,6}tables_security: fix future section mismatch
selinux: use nf_register_hooks()
netfilter: ebtables: use nf_register_hooks()
Revert "pkt_sched: sch_sfq: dump a real number of flows"
qeth: use dev->ml_priv instead of dev->priv
syncookies: Make sure ECN is disabled
net: drop unused BUG_TRAP()
net: convert BUG_TRAP to generic WARN_ON
drivers/net: convert BUG_TRAP to generic WARN_ON
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON() though some might actually be
promoted to BUG_ON() but I left that to future.
I could make at least one BUILD_BUG_ON conversion.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
All ratelimit user use same jiffies and burst params, so some messages
(callbacks) will be lost.
For example:
a call printk_ratelimit(5 * HZ, 1)
b call printk_ratelimit(5 * HZ, 1) before the 5*HZ timeout of a, then b will
will be supressed.
- rewrite __ratelimit, and use a ratelimit_state as parameter. Thanks for
hints from andrew.
- Add WARN_ON_RATELIMIT, update rcupreempt.h
- remove __printk_ratelimit
- use __ratelimit in net_ratelimit
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
pkt_sched: sch_sfq: dump a real number of flows
atm: [fore200e] use MODULE_FIRMWARE() and other suggested cleanups
netfilter: make security table depend on NETFILTER_ADVANCED
tcp: Clear probes_out more aggressively in tcp_ack().
e1000e: fix e1000_netpoll(), remove extraneous e1000_clean_tx_irq() call
net: Update entry in af_family_clock_key_strings
netdev: Remove warning from __netif_schedule().
sky2: don't stop queue on shutdown
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
cpumask: Provide a generic set of CPUMASK_ALLOC macros
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
Revert "cpumask: introduce new APIs"
cpumask: make for_each_cpu_mask a bit smaller
net: Pass reference to cpumask variable in net/sunrpc/svc.c
...
Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually
In the merge phase of the CAN subsystem the
af_family_clock_key_strings[] have been added to sock.c in commit
443aef0edd
(lockdep: fixup sk_callback_lock annotation). This trivial patch adds
the missing name for address family 29 (AF_CAN).
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It isn't helping anything and we aren't going to be able to change all
the drivers that do queue wakeups in strange situations.
Just letting a noop_qdisc get scheduled will work because when
qdisc_run() executes via net_tx_work() it will simply find no packets
pending when it makes the ->dequeue() call in qdisc_restart.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (24 commits)
I/OAT: I/OAT version 3.0 support
I/OAT: tcp_dma_copybreak default value dependent on I/OAT version
I/OAT: Add watchdog/reset functionality to ioatdma
iop_adma: cleanup iop_chan_xor_slot_count
iop_adma: document how to calculate the minimum descriptor pool size
iop_adma: directly reclaim descriptors on allocation failure
async_tx: make async_tx_test_ack a boolean routine
async_tx: remove depend_tx from async_tx_sync_epilog
async_tx: export async_tx_quiesce
async_tx: fix handling of the "out of descriptor" condition in async_xor
async_tx: ensure the xor destination buffer remains dma-mapped
async_tx: list_for_each_entry_rcu() cleanup
dmaengine: Driver for the Synopsys DesignWare DMA controller
dmaengine: Add slave DMA interface
dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmap
dmaengine: Add dma_client parameter to device_alloc_chan_resources
dmatest: Simple DMA memcpy test client
dmaengine: DMA engine driver for Marvell XOR engine
iop-adma: fix platform driver hotplug/coldplug
dmaengine: track the number of clients using a channel
...
Fixed up conflict in drivers/dca/dca-sysfs.c manually
I/OAT DMA performance tuning showed different optimal values of
tcp_dma_copybreak for different I/OAT versions (4096 for 1.2 and 2048
for 2.0). This patch lets ioatdma driver set tcp_dma_copybreak value
according to these results.
[dan.j.williams@intel.com: remove some ifdefs]
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The new address list lock needs to handle the same device layering
issues that the _xmit_lock one does.
This integrates work done by Patrick McHardy.
Signed-off-by: David S. Miller <davem@davemloft.net>
The function header comments have to go with the functions
they are documenting, or things go horribly wrong when we
try to process them with the docbook tools.
Warning(include/linux/netdevice.h:1006): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1033): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1067): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1093): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1474): No description found for parameter 'txq'
Error(net/core/dev.c:1674): cannot understand prototype: 'u32 simple_tx_hashrnd; '
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Dave:
This patch adds a function to get the driver name from a struct net_device,
and consequently uses this in the watchdog timeout handler to print as
part of the message.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor nit, use size_t for allocation size and kcalloc to allocate
an array. Probably makes no actual code difference.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon feedback from Eric Dumazet and Andi Kleen.
Cure several deficiencies in simple_tx_hash() by using
jhash + reciprocol multiply.
1) Eliminates expensive modulus operation.
2) Makes hash less attackable by using random seed.
3) Eliminates endianness hash distribution issues.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use sockaddr_storage{} for generic socket address storage
and ensures proper alignment.
Use sockaddr{} for pointers to omit several casts.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
