We plan to use fsl,esdhc going forward as the base compatible so update
the driver to bind against it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
When a software timeout occurs in polling mode hardware was left in
an indeterminate state causing subsequent operations to block.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
This is a temporary workaround until the MMC stack can be fixed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Ideally we should have a directory of drivers and a link to the 'active'
driver. For now just show the first device which is effectively the existing
semantics without a warning.
This is an update on the original buggy patch that I then forgot to
resubmit. Confusingly it was proposed by Red Hat, written by Etched Pixels
fixed and submitted by Intel ...
Resolves-Bug: http://bugzilla.kernel.org/show_bug.cgi?id=9749
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This matches Bartlomiej's patch for ide_pci_generic:
c339dfdd65
In the libata case netcell has its own mini driver. I suspect this fix is
actually only needed for some firmware revs but it does no harm either way.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch to fix bad length checking in e1000. E1000 by default does two
things:
1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put
Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set. This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test). If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb. This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU. The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000. This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phy_power_down parameter to forcedeth: set to 1 to power down the
phy and disable the link when an interface goes down; set to 0 to always
leave the phy powered up.
The phy power state persists across reboots; Windows, some BIOSes, and
older versions of Linux don't bother to power up the phy again, forcing
users to remove all power to get the interface working (see
http://bugzilla.kernel.org/show_bug.cgi?id=13072). Leaving the phy
powered on is the safest default behavior. Users accustomed to seeing
the link state reflect the interface state and/or wanting to minimize
power consumption can set phy_power_down=1 if compatibility with other
OSes is not an issue.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Several EISA device IDs for 3c509 family network cards are missing from
the driver, making the cards unusable in their EISA mode. Here's a fix to
add them based on the EISA configuration files distributed by 3Com and our
eisa.ids database.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to explicitly mark words 85-87 as valid ones since
firmware doesn't do it.
This should fix support for LBA48 and FLUSH CACHE [EXT] command
which stopped working after we applied more strict checking of
identify words in:
commit 942dcd85bf
("ide: idedisk_supports_lba48() -> ata_id_lba48_enabled()")
and
commit 4b58f17d7c
("ide: ide_id_has_flush_cache() -> ata_id_flush_enabled()")
Reported-and-tested-by: "Trevor Hemsley" <trevor.hemsley@ntlworld.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
fsldma: Fix compile warnings
fsldma: fix memory leak on error path in fsl_dma_prep_memcpy()
fsldma: snooping is not enabled for last entry in descriptor chain
fsldma: fix infinite loop on multi-descriptor DMA chain completion
fsldma: fix "DMA halt timeout!" errors
fsldma: fix check on potential fdev->chan[] overflow
fsldma: update mailling list address in MAINTAINERS
Gary Lin reports that a new device id needs to be added to the atl1e in
order to get some new Asus hardware to work properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the transmit queue gets full we enable interrupts for TX completions
There was a race that we handled the TX queue both from the interrupt context
and from the transmit function. Using "spin_trylock_irq()" ensures this
doesn't happen.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/built-in.o: In function `intel_opregion_init':
(.text+0x9d540): undefined reference to `acpi_video_register'
v2: move under DRM_I915 from DRM_I915_KMS
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Commit 4973b22a ("ACPI processor: reset the throttling state once it's
invalid") introduced a new warning which prints a spurious newline.
The ACPI_WARNING macro that is used already takes care of adding a
newline, after adding ACPI_CA_VERSION to the message. Remove the newline
to avoid the message getting split into two lines.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently acpi_video_exit() is exported as well as using __exit which causes:
WARNING: drivers/acpi/video.o(__ksymtab+0x0): Section mismatch in reference from the variable __ksymtab_acpi_video_exit to the function .exit.text:acpi_video_exit()
The symbol acpi_video_exit is exported and annotated __exit
Fix this by removing the __exit annotation of acpi_video_exit or drop the export.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When BIOS SETUP is changed to disable EIST, some BIOS
hand the OS an un-initialized _PSS:
Name (_PSS, Package (0x06)
{
Package (0x06)
{
0x80000000, // frequency [MHz]
0x80000000, // power [mW]
0x80000000, // latency [us]
0x80000000, // BM latency [us]
0x80000000, // control
0x80000000 // status
},
...
These are outrageous values for frequency,
power and latency, raising the question where to draw
the line between legal and illegal. We tend to survive
garbage in the power and latency fields, but we can BUG_ON
when garbage is in the frequency field.
Cpufreq multiplies the frequency by 1000 and stores it in a u32 KHz.
So disregard a _PSS with a frequency so large
that it can't be represented by cpufreq.
https://bugzilla.redhat.com/show_bug.cgi?id=500311
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
Revert "USB: Correct Makefile to make isp1760 buildable"
usb-serial: fix crash when sub-driver updates firmware
USB: isp1760: urb_dequeue doesn't always find the urbs
USB: Yet another Conexant Clone to add to cdc-acm.c
USB: atmel_usb_udc: Use kzalloc() to allocate ep structures
USB: atmel-usba-udc : fix control out requests.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Driver Core: do not oops when driver_unregister() is called for unregistered drivers
sysfs: file.c: use create_singlethread_workqueue()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: libps2 - better handle bad scheduler decisions
Input: usb1400_ts - fix access to "device data" in resume function
Input: multitouch - augment event semantics documentation
Input: multitouch - add tracking ID to the protocol
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
i915: Set object to gtt domain when faulting it back in
drm/i915: Apply a big hammer to 865 GEM object CPU cache flushing.
drm/i915: Fix tiling pitch handling on 8xx.
If you setserial a port which has never been initialised we change the type
but don't update the I/O method pointers. The same problem is true if you
change the io type of a port - but nobody ever does that so nobody noticed!
Remember the old type and when attaching if the type has changed reload the
port accessor pointers. We can't do it blindly as some 8250 drivers load custom
accessors and we must not stomp those.
Tested-by: Victor Seryodkin <vvscore@gmail.com>
Closes-bug: #13367
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The amd8111_edac.c driver will fail allmodconfig on architectures other
than PPC, introduce Kconfig dependency to avoid this, since both AMD8111
and AMD8131 chips are only adopted on Maple so far.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "bus_id" member in the device structure has been obsolete, use
dev_name() instead.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove wrong fifo size definition for some AT91 products.
Due to a misunderstanding of some AT91 datasheets, a fifo size of 2048
(words) has been introduced by mistake. In fact, all products (AT91/AT32)
are sharing the same fifo size of 512 words.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correctly restore the FrameBuffer register state in the resume function.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/serial/8250_gsc.c:44: warning: format '%lx' expects type
'long unsigned int', but argument 2 has type 'resource_size_t'
[akpm@linux-foundation.org: fix it to handle u64's]
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/parport/parport_gsc.c:356: warning: format '%lx' expects type
'long unsigned int', but argument 2 has type 'resource_size_t'
[akpm@linux-foundation.org: fix it to handle u64's]
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The check for an overindexing of mpc52xx_uart_{ports,nodes} has an
off-by-one.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
http://bugzilla.kernel.org/show_bug.cgi?id=13312
at76_dwork_hw_scan holds a mutex while calling ieee80211_scan_completed,
which then calls at76_config which needs the same mutex. This reworks
the ordering to not hold the lock while calling ieee80211_scan_completed.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following patch fixes:
- re-initialization of host->col_addr which is used as byte index
between the successive READID flash commands.
- compile error when CONFIG_PM is enabled
- pass on the error code from clk_get()
- return -ENOMEM in case of failed ioremap()
- pass on the return value of platform_driver_probe() directly
- remove excessive printk
- let command line partition table parsing with mxc_nand name.
The cmd_line parsing is done via <mtd-id> name that differs
from mxc_nand by default and looks like "NAND 256MiB 1,8V 8-bit"
Signed-off-by: Vladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix the build for CONFIG_NET_POLL_CONTROLLER that I broke with
217cbfa856 ("mac8390: fix regression
caused during net_device_ops conversion").
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not call t3_link_fault() under spinlock, as it calls msleep().
Besides, only the access to pi->link_fault needs to be serialized.
Also initialize local variables before checking the link status,
link state fields might otherwise end up containing garbage.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5e68b772e6
cxgb3: map entire Rx page, feed map+offset to Rx ring.
introduced a regression on platforms defining DECLARE_PCI_UNMAP_ADDR()
and related macros as no-ops.
Rx descriptors are fed with the a page buffer bus address + page chunk offset.
The page buffer bus address is set and retrieved through
pci_unamp_addr_set(), pci_unmap_addr().
These functions being meaningless on x86 (if CONFIG_DMA_API_DEBUG is not set).
The HW ends up with a bogus bus address.
This patch saves the page buffer bus address for all plaftorms.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing the i7300_idle driver on i5000-series hardware required
an edit to i7300_idle.h to "#define SUPPORT_I5000 1" and a re-build
of both i7300_idle and ioat_dma.
Replace that build-time scheme with a load-time module parameter:
"7300_idle.forceload=1" to make it easier to test the driver
on hardware that while not officially validated, works fine
and is much more commonly available.
By default (no modparam) the driver will continue to load
only on the i7300.
Note that ioat_dma runs a copy of i7300_idle's probe routine
to know to reserve an IOAT channel for i7300_idle.
This change makes ioat_dma do that always on the i5000,
just like it does on the i7300.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Andrew Henroid <andrew.d.henroid@intel.com>
We also fix a problem with cleaning up properly when initializing
drivers and devices, so checks like this will work successfully.
Portions of the patch by Linus and Greg and Ingo.
Reported-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 26e1287594.
A larger patch (f7e7aa585) a few days after this one added the same line
to the Makefile, but in a different place. While it'd be more correct to
revert that one, it's easier to revert this one because this is a
one-liner.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1244) fixes a crash in usb-serial that occurs when a
sub-driver returns a positive value from its attach method, indicating
that new firmware was loaded and the device will disconnect and
reconnect. The usb-serial core then skips the step of registering the
port devices; when the disconnect occurs, the attempt to unregister
the ports fails dramatically.
This problem shows up with Keyspan devices and it might affect others
as well.
When the attach method returns a positive value, the patch sets
num_ports to 0. This tells usb_serial_disconnect() not to try
unregistering any of the ports; instead they are cleaned up by
destroy_serial().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The option driver (and presumably others) allocates several URBs when it
opens and tries to free them when it closes. The isp1760_urb_dequeue
function gets called, but the packet being dequeued is not necessarily at
the
front of one of the 32 queues. If not, the isp1760_urb_done function doesn't
get called for the URB and the process trying to free it hangs forever on a
wait_queue. This patch does two things. If the URB being dequeued has others
queued behind it, it re-queues them. And it searches the queues looking for
the URB being dequeued rather than just looking at the one at the front of
the queue.
[bigeasy@linutronix] whitespace fixes, reformating
Cc: stable <stable@kernel.org>
Signed-off-by: Warren Free <wfree@ipmn.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds another quirky Conexant USB Modem Clone to usb cdc-acm.c
Signed-off-by: Xiao Kaijian <xiaokj@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This ensures that all fields are properly initialized.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbtest #14 was failing with "udc: ep0: TXCOMP: Invalid endpoint state 2, halting endpoint..."
This occured since ep0 is bidirectional and ep->is_in is not valid (must always use ep->state)
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sometimes devices send us their responses in time but due to
unfortunate scheduling decisions the receiving thread does not
get scheduled till much later and we erroneously decide that
device timed out. Work around this problem by checking whether we
received the data we needed instead of checking timeout
condition.
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The 'dev' field of struct acpi_pci_data is having a pointer to struct
pci_dev without incrementing the reference counter. Because of this, I
got the following kernel oops when I was doing some pci hotplug
operations. This patch fixes this bug by replacing wrong hand-made
pci_find_slot() with pci_get_slot() in acpi_pci_bind().
BUG: unable to handle kernel NULL pointer dereference at 00000000000000e8
IP: [<ffffffff803f0e9b>] acpi_pci_unbind+0xb1/0xdd
Call Trace:
[<ffffffff803ecee4>] acpi_bus_remove+0x54/0x68
[<ffffffff803ecf6d>] acpi_bus_trim+0x75/0xe3
[<ffffffffa0345ddd>] acpiphp_disable_slot+0x16d/0x1e0 [acpiphp]
[<ffffffffa03441f0>] disable_slot+0x20/0x60 [acpiphp]
[<ffffffff803cfc18>] power_write_file+0xc8/0x110
[<ffffffff803c6a54>] pci_slot_attr_store+0x24/0x30
[<ffffffff803469ce>] sysfs_write_file+0xce/0x140
[<ffffffff802e94e7>] vfs_write+0xc7/0x170
[<ffffffff802e9aa0>] sys_write+0x50/0x90
[<ffffffff8020bd6b>] system_call_fastpath+0x16/0x1b
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Tested-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We we build with dma_addr_t as a 64-bit quantity we get:
drivers/dma/fsldma.c: In function 'fsl_chan_xfer_ld_queue':
drivers/dma/fsldma.c:625: warning: cast to pointer from integer of different size
drivers/dma/fsldma.c: In function 'fsl_dma_chan_do_interrupt':
drivers/dma/fsldma.c:737: warning: cast to pointer from integer of different size
drivers/dma/fsldma.c:737: warning: cast to pointer from integer of different size
drivers/dma/fsldma.c: In function 'of_fsl_dma_probe':
drivers/dma/fsldma.c:927: warning: cast to pointer from integer of different
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When a GEM object is evicted from the GTT we set it to the CPU domain,
as it might get swapped in and out or ever mmapped regularly. If the
object is mmapped through the GTT it can still get evicted in this way
by other objects requiring GTT space. When the GTT mapping is touched
again we fault it back into the GTT, but fail to set it back to the
GTT domain. This means we fail to flush any cached CPU writes to the
pages backing the object which will then happen "eventually", typically
after we write to the page through the uncached GTT mapping.
[anholt: Note that userland does do a set_domain(GTT, GTT) when starting
to access the GTT mapping. That covers getting the existing mapping of the
object synchronized if it's bound to the GTT. But set_domain(GTT, GTT)
doesn't do anything if the object is currently unbound. This fix covers the
transition to being bound for GTT mapping.]
Fixes glyph and other pixmap corruption during swapping. fd.o bug #21790
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
platform_data != driver_data
driver data is actually the "correct" place of the struct however it is
not placed there due to the need of the ac97 struct. This is broken since
d9105c2b01 aka "[ARM] 5184/1: Split ucb1400_ts into core and touchscreen"
Signed-off-by: Manuel Traut <manut@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A recent patch to raid5.c use min on an int and a sector_t.
This isn't allowed.
So change it to min_t(sector_t,x,y).
Signed-off-by: NeilBrown <neilb@suse.de>
An oops can occur if a user attempts to use both PCI logical
hotplug and the ACPI physical hotplug driver (acpiphp) in this
sequence, where $slot/address == $device.
In other words, if acpiphp has claimed a PCI device, and that
device is logically removed, then acpiphp may oops when it
attempts to access it again.
# echo 1 > /sys/bus/pci/devices/$device/remove
# echo 0 > /sys/bus/pci/slots/$slot/power
Unable to handle kernel NULL pointer dereference (address 0000000000000000)
Call Trace:
[<a000000100016390>] show_stack+0x50/0xa0
[<a000000100016c60>] show_regs+0x820/0x860
[<a00000010003b390>] die+0x190/0x2a0
[<a000000100066a40>] ia64_do_page_fault+0x8e0/0xa40
[<a00000010000c7a0>] ia64_native_leave_kernel+0x0/0x270
[<a0000001003b2660>] pci_remove_bus_device+0x120/0x260
[<a0000002060549f0>] acpiphp_disable_slot+0x410/0x540 [acpiphp]
[<a0000002060505c0>] disable_slot+0xc0/0x120 [acpiphp]
[<a0000002040d21c0>] power_write_file+0x1e0/0x2a0 [pci_hotplug]
[<a0000001003bb820>] pci_slot_attr_store+0x60/0xa0
[<a000000100240f70>] sysfs_write_file+0x230/0x2c0
[<a000000100195750>] vfs_write+0x190/0x2e0
[<a0000001001961a0>] sys_write+0x80/0x100
[<a00000010000c600>] ia64_ret_from_syscall+0x0/0x20
[<a000000000010720>] __kernel_syscall_via_break+0x0/0x20
The root cause of this oops is that the logical remove ("echo 1 >
/sys/bus/pci/devices/$device/remove") destroyed the pci_dev. The
pci_dev struct itself wasn't deallocated because acpiphp kept a
reference, but some of its fields became invalid.
acpiphp doesn't have any real reason to keep a pointer to a
pci_dev around. It can always derive it using pci_get_slot().
If a logical remove destroys the pci_dev, acpiphp won't find it
and is thus prevented from causing mischief.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reported-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The previous commit "convert to net_device_ops" broke the Blackfin MAC
driver as it declared the new structure before the function it used:
CC drivers/net/bfin_mac.o
drivers/net/bfin_mac.c:984: error: ‘bfin_mac_close’ undeclared here (not in a function)
make[1]: *** [drivers/net/bfin_mac.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both atl1.c and atl2.c include atlx.h, which defines some modinfo
stuff. But atl2.c seems like it doesn't want the modinfo data
from atlx.h, as it defines its own.
Running modinfo on atl2.ko, we get conflicting information:
$ /sbin/modinfo drivers/net/atlx/atl2.ko | egrep "version|description|author"
version: 2.2.3
description: Atheros Fast Ethernet Network Driver
author: Atheros Corporation <xiong.huang@atheros.com>, Chris Snook <csnook@redhat.com>
version: 2.1.3
author: Xiong Huang <xiong.huang@atheros.com>, Chris Snook <csnook@redhat.com>, Jay Cliburn <jcliburn@gmail.com>
Move the modinfo data out of atlx.h and into atl1.c to eliminate
the confusion:
$ /sbin/modinfo drivers/net/atlx/atl1.ko | egrep "version|description|author"
version: 2.1.3
author: Xiong Huang <xiong.huang@atheros.com>, Chris Snook <csnook@redhat.com>, Jay Cliburn <jcliburn@gmail.com>
description: Atheros L1 Gigabit Ethernet Driver
$ /sbin/modinfo drivers/net/atlx/atl2.ko | egrep "version|description|author"
version: 2.2.3
description: Atheros Fast Ethernet Network Driver
author: Atheros Corporation <xiong.huang@atheros.com>, Chris Snook <csnook@redhat.com>
Reported-by: Scott Scriven <scott.scriven@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gianfar interrupt handler uses IEVENT_ERR_MASK to check and handle errors.
Babbling RX error (IEVENT_BABR) should be included in IEVENT_ERROR_MASK.
Otherwise if BABR is raised, it never gets handled nor cleared, and an
interrupt storm results. This has been observed to happen on sending a
burst of ethernet frames to a gianfar based board.
Signed-off-by: Xiaotian Feng <xiaotian.feng@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When AMD C1E is enabled, local APIC timer will stop even in C1. To avoid
suspend/resume hang, this patch removes C1 and replace it with a cpu_relax() in
suspend/resume path. This hasn't any impact in runtime path.
http://bugzilla.kernel.org/show_bug.cgi?id=13233
[ impact: avoid suspend/resume hang in AMD CPU with C1E enabled ]
Tested-by: Dmitry Lyzhyn <thisistempbox@yahoo.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When AMD C1E is enabled, local APIC timer will stop even in C1.
This patch uses broadcast IPI to replace local APIC timer in C1.
http://bugzilla.kernel.org/show_bug.cgi?id=13233
[ impact: avoid boot hang in AMD CPU with C1E enabled ]
Tested-by: Dmitry Lyzhyn <thisistempbox@yahoo.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On the 865, but not the 855, the clflush we do appears to not actually make
it out to the hardware all the time. An easy way to safely reproduce was
X -retro, which would show that some of the blits involved in drawing the
lovely root weave didn't make it out to the hardware. Those blits are 32
bytes each, and 1-2 would be missing at various points around the screen.
Other experimentation (doing more clflush, doing more AGP chipset flush,
poking at some more device registers to maybe trigger more flushing) didn't
help. krh came up with the wbinvd as a way to successfully get all those
blits to appear.
Signed-off-by: Eric Anholt <eric@anholt.net>
The pitch field is an exponent on pre-965, so we were rejecting buffers
on 8xx that we shouldn't have. 915 got lucky in that the largest legal
value happened to match (8KB / 512 = 0x10), but 8xx has a smaller tile width.
Additionally, we programmed that bad value into the register on 8xx, so the
only pitch that would work correctly was 4096 (512-1023 pixels), while others
would probably give bad rendering or hangs.
Signed-off-by: Eric Anholt <eric@anholt.net>
fd.o bug #20473.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Add support for VGA load detection (pre-945).
drm/i915: Use an I2C algo to do the flip to SDVO DDC bus.
drm/i915: Determine type before initialising connector
drm/i915: Return SDVO LVDS VBT mode if no EDID modes are detected.
drm/i915: Fetch SDVO LVDS mode lines from VBT, then reserve them
i915: support 8xx desktop cursors
drm/i915: allocate large pointer arrays with vmalloc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] powernow-k8: determine exact CPU frequency for HW Pstates
[CPUFREQ] powernow-k8 cleanup msg if BIOS does not export ACPI _PSS cpufreq data
[CPUFREQ] fix timer teardown in ondemand governor
[CPUFREQ] fix timer teardown in conservative governor
[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call
[CPUFREQ] powernow-k7 build fix when ACPI=n
[CPUFREQ] add atom family to p4-clockmod
When KVM is loaded, and hence VT set up, the vmcall instruction in an
lguest guest causes a #GP, not #UD.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
r8169: avoid losing MSI interrupts
tcp: tcp_vegas ssthresh bugfix
mac8390: fix regression caused during net_device_ops conversion
gianfar: fix BUG under load after introduction of skb recycling
wimax/i2400m: usb: fix device reset on autosuspend while not yet idle
RxRPC: Error handling for rxrpc_alloc_connection()
ipv4: Fix oops with FIB_TRIE
pktgen: do not access flows[] beyond its length
gigaset: beyond ARRAY_SIZE of iwb->data
IPv6: set RTPROT_KERNEL to initial route
net: fix rtable leak in net/ipv4/route.c
net: fix length computation in rt_check_expire()
wireless: beyond ARRAY_SIZE of intf->crypto_stats
iwlwifi: update 5000 ucode support to version 2 of API
cfg80211: fix race between core hint and driver's custom apply
airo: fix airo_get_encode{,ext} buffer overflow like I mean it...
ath5k: fix interpolation with equal power levels
iwlwifi: do not cancel delayed work inside spin_lock_irqsave
ath5k: fix exp off-by-one when computing OFDM delta slope
wext: verify buffer size for SIOCSIWENCODEEXT
...
Two approaches for VGA detections: hot plug detection for 945G onwards
and load pipe detection for Pre-945G. Load pipe detection will get one free
pipe, set border color as red and blue, then check CRT status by
swf register. This is a sync-up with the 2D driver.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* Rafael J. Wysocki (rjw@sisk.pl) wrote:
> This message has been generated automatically as a part of a report
> of regressions introduced between 2.6.28 and 2.6.29.
>
> The following bug entry is on the current list of known regressions
> introduced between 2.6.28 and 2.6.29. Please verify if it still should
> be listed and let me know (either way).
>
>
> Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=13186
> Subject : cpufreq timer teardown problem
> Submitter : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Date : 2009-04-23 14:00 (24 days old)
> References : http://marc.info/?l=linux-kernel&m=124049523515036&w=4
> Handled-By : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Patch : http://patchwork.kernel.org/patch/19754/
> http://patchwork.kernel.org/patch/19753/
>
(updated changelog)
cpufreq fix timer teardown in ondemand governor
The problem is that dbs_timer_exit() uses cancel_delayed_work() when it should
use cancel_delayed_work_sync(). cancel_delayed_work() does not wait for the
workqueue handler to exit.
The ondemand governor does not seem to be affected because the
"if (!dbs_info->enable)" check at the beginning of the workqueue handler returns
immediately without rescheduling the work. The conservative governor in
2.6.30-rc has the same check as the ondemand governor, which makes things
usually run smoothly. However, if the governor is quickly stopped and then
started, this could lead to the following race :
dbs_enable could be reenabled and multiple do_dbs_timer handlers would run.
This is why a synchronized teardown is required.
The following patch applies to, at least, 2.6.28.x, 2.6.29.1, 2.6.30-rc2.
Depends on patch
cpufreq: remove rwsem lock from CPUFREQ_GOV_STOP call
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: gregkh@suse.de
CC: stable@kernel.org
CC: cpufreq@vger.kernel.org
CC: Ingo Molnar <mingo@elte.hu>
CC: rjw@sisk.pl
CC: Ben Slusky <sluskyb@paranoiacs.org>
Signed-off-by: Dave Jones <davej@redhat.com>
* Rafael J. Wysocki (rjw@sisk.pl) wrote:
> This message has been generated automatically as a part of a report
> of regressions introduced between 2.6.28 and 2.6.29.
>
> The following bug entry is on the current list of known regressions
> introduced between 2.6.28 and 2.6.29. Please verify if it still should
> be listed and let me know (either way).
>
>
> Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=13186
> Subject : cpufreq timer teardown problem
> Submitter : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Date : 2009-04-23 14:00 (24 days old)
> References : http://marc.info/?l=linux-kernel&m=124049523515036&w=4
> Handled-By : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Patch : http://patchwork.kernel.org/patch/19754/
> http://patchwork.kernel.org/patch/19753/
>
(re-send with updated changelog)
cpufreq fix timer teardown in conservative governor
The problem is that dbs_timer_exit() uses cancel_delayed_work() when it should
use cancel_delayed_work_sync(). cancel_delayed_work() does not wait for the
workqueue handler to exit.
The ondemand governor does not seem to be affected because the
"if (!dbs_info->enable)" check at the beginning of the workqueue handler returns
immediately without rescheduling the work. The conservative governor in
2.6.30-rc has the same check as the ondemand governor, which makes things
usually run smoothly. However, if the governor is quickly stopped and then
started, this could lead to the following race :
dbs_enable could be reenabled and multiple do_dbs_timer handlers would run.
This is why a synchronized teardown is required.
Depends on patch
cpufreq: remove rwsem lock from CPUFREQ_GOV_STOP call
The following patch applies to 2.6.30-rc2. Stable kernels have a similar
issue which should also be fixed, but the code changed between 2.6.29
and 2.6.30, so this patch only applies to 2.6.30-rc.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: gregkh@suse.de
CC: stable@kernel.org
CC: cpufreq@vger.kernel.org
CC: Ingo Molnar <mingo@elte.hu>
CC: rjw@sisk.pl
CC: Ben Slusky <sluskyb@paranoiacs.org>
Signed-off-by: Dave Jones <davej@redhat.com>
* Rafael J. Wysocki (rjw@sisk.pl) wrote:
> This message has been generated automatically as a part of a report
> of regressions introduced between 2.6.28 and 2.6.29.
>
> The following bug entry is on the current list of known regressions
> introduced between 2.6.28 and 2.6.29. Please verify if it still should
> be listed and let me know (either way).
>
>
> Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=13186
> Subject : cpufreq timer teardown problem
> Submitter : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Date : 2009-04-23 14:00 (24 days old)
> References : http://marc.info/?l=linux-kernel&m=124049523515036&w=4
> Handled-By : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Patch : http://patchwork.kernel.org/patch/19754/
> http://patchwork.kernel.org/patch/19753/
The patches linked above depend on the following patch to remove
circular locking dependency :
cpufreq: remove rwsem lock from CPUFREQ_GOV_STOP call
(the following issue was faced when using cancel_delayed_work_sync() in the
timer teardown (which fixes a race).
* KOSAKI Motohiro (kosaki.motohiro@jp.fujitsu.com) wrote:
> Hi
>
> my box output following warnings.
> it seems regression by commit 7ccc7608b836e58fbacf65ee4f8eefa288e86fac.
>
> A: work -> do_dbs_timer() -> cpu_policy_rwsem
> B: store() -> cpu_policy_rwsem -> cpufreq_governor_dbs() -> work
>
>
Hrm, I think it must be due to my attempt to fix the timer teardown race
in ondemand governor mixed with new locking behavior in 2.6.30-rc.
The rwlock seems to be taken around the whole call to
cpufreq_governor_dbs(), when it should be only taken around accesses to
the locked data, and especially *not* around the call to
dbs_timer_exit().
Reverting my fix attempt would put the teardown race back in place
(replacing the cancel_delayed_work_sync by cancel_delayed_work).
Instead, a proper fix would imply modifying this critical section :
cpufreq.c: __cpufreq_remove_dev()
...
if (cpufreq_driver->target)
__cpufreq_governor(data, CPUFREQ_GOV_STOP);
unlock_policy_rwsem_write(cpu);
To make sure the __cpufreq_governor() callback is not called with rwsem
held. This would allow execution of cancel_delayed_work_sync() without
being nested within the rwsem.
Applies on top of the 2.6.30-rc5 tree.
Required to remove circular dep in teardown of both conservative and
ondemande governors so they can use cancel_delayed_work_sync().
CPUFREQ_GOV_STOP does not modify the policy, therefore this locking seemed
unneeded.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Greg KH <greg@kroah.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: "Rafael J. Wysocki" <rjw@sisk.pl>
CC: Ben Slusky <sluskyb@paranoiacs.org>
CC: Chris Wright <chrisw@sous-sol.org>
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The 8169 chip only generates MSI interrupts when all enabled event
sources are quiescent and one or more sources transition to active. If
not all of the active events are acknowledged, or a new event becomes
active while the existing ones are cleared in the handler, we will not
see a new interrupt.
The current interrupt handler masks off the Rx and Tx events once the
NAPI handler has been scheduled, which opens a race window in which we
can get another Rx or Tx event and never ACK'ing it, stopping all
activity until the link is reset (ifconfig down/up). Fix this by always
ACK'ing all event sources, and loop in the handler until we have all
sources quiescent.
Signed-off-by: David Dillow <dave@thedillows.org>
Tested-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changeset ca17584bf2 ("mac8390: update
to net_device_ops") broke mac8390 by adding 8390.o to the link. That
meant that lib8390.c was included twice, once in mac8390.c and once in
8390.c, subject to different macros. This patch reverts that by
avoiding the wrappers in 8390.c. They seem to be of no value since
COMPAT_NET_DEV_OPS is going away soon.
Tested with a Kinetics EtherPort card.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the metadata to always be consistent, we mustn't updated
curr_resync_completed without also updating reshape_position.
The reshape code updates both at the same time. However since
commit 97e4f42d62
the common md_do_sync will sometimes update curr_resync_completed
but is not in a position to update reshape_position.
So if MD_RECOVERY_RESHAPE is set (indicating that a reshape is
happening, so reshape_position might change), don't update
curr_resync_completed in md_do_sync, leave it to the per-personality
reshape code.
Signed-off-by: NeilBrown <neilb@suse.de>
As sector_t in unsigned, we cannot afford to let 'safepos' etc go
negative.
So replace
a -= b;
by
a -= min(b,a);
Signed-off-by: NeilBrown <neilb@suse.de>
The md resync engine has a 'frozen' state which ensures that
no resync/recovery. This is used to avoid races.
Export this state through the 'sync_action' sysfs attribute
so that user-space can benefit and also avoid some races.
Signed-off-by: NeilBrown <neilb@suse.de>
The code for checking which bits in the bitmap can be cleared
has 2 problems:
1/ it repeatedly takes and drops a spinlock, where it would make
more sense to just hold on to it most of the time.
2/ it doesn't make use of some opportunities to skip large sections
of the bitmap
This patch fixes those. It will only affect CPU consumption, not
correctness.
Signed-off-by: NeilBrown <neilb@suse.de>
Instead of always returns EINVAL if anything goes wrong
when setting the array size, add the option of
E2BIG
if the size requested is too large. This makes it easier
for user-space to be sure what went wrong.
Signed-off-by: NeilBrown <neilb@suse.de>
We previously didn't update these fields when writing the metadata
because they could never change. They can now, so we better write
them.
v0.90 metadata always updated these fields.
Signed-off-by: NeilBrown <neilb@suse.de>
Since commit 0fd56bb5be ("gianfar:
Add support for skb recycling"), gianfar puts skbuffs that are in
the rx ring back onto the recycle list as-is in case there was a
receive error, but this breaks the following invariant: that all
skbuffs on the recycle list have skb->data = skb->head + NET_SKB_PAD.
The RXBUF_ALIGNMENT realignment done in gfar_new_skb() will be done
twice on skbuffs recycled in this way, causing there not to be enough
room in the skb anymore to receive a full packet, eventually leading
to an skb_over_panic from gfar_clean_rx_ring() -> skb_put().
Resetting the skb->data pointer to skb->head + NET_SKB_PAD before
putting the skb back onto the recycle list restores the mentioned
invariant, and should fix this issue.
Reported-by: Michael Guntsche <mike@it-loops.com>
Tested-by: Michael Guntsche <mike@it-loops.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't hold dpm_list_mtx while executing
[disable|enable]_nonboot_cpus(), because theoretically this may lead
to a deadlock as shown by the following example (provided by Johannes
Berg):
CPU 3 CPU 2 CPU 1
suspend/hibernate
something:
rtnl_lock() device_pm_lock()
-> mutex_lock(&dpm_list_mtx)
mutex_lock(&dpm_list_mtx)
linkwatch_work
-> rtnl_lock()
disable_nonboot_cpus()
-> flush CPU 3 workqueue
Fortunately, device drivers are supposed to stop any activities that
might lead to the registration of new device objects way before
disable_nonboot_cpus() is called, so it shouldn't be necessary to
hold dpm_list_mtx over the entire late part of device suspend and
early part of device resume.
Thus, during the late suspend and the early resume of devices acquire
dpm_list_mtx only when dpm_list is going to be traversed and release
it right after that.
This patch is reported to fix the regressions tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=13245.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Miles Lane <miles.lane@gmail.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
There are a few multi-touch devices that support finger tracking
well in hardware, Stantum being the prime example. By exposing the
tracking ID in the MT protocol, evdev bandwidth and cpu usage in
user space can be reduced.
This patch adds the ABS_MT_TRACKING_ID to the MT protocol.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Stéphane Chatty <chatty@enac.fr>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Previously, we would set the control bus switch before calls were made
to request EDID information over DDC. But recently the DDC code started
doing multiple I2C transfers to get the EDID extensions as well. This
tripped up SDVO, because the control bus switch is only in effect until
the next STOP after a START. By doing our own algo, we can wrap each i2c
transaction on the DDC I2C bus with the control bus switch it requires.
freedesktop.org bug #21042
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: Hand application for conflict, fixed error path]
Signed-off-by: Eric Anholt <eric@anholt.net>
drm_connector_init sets both the connector type and the connector type_id
on the newly initialised connector. As the connector type_id is coupled to
the connector type, the connector type cannot simply be modified on an
initialised connector.
This patch changes the order of operations on intel_sdvo_init so that the
type is determined before the connector is intialised.
This fixes a bug whereby the name card0-VGA-1 would be allocted to both a
CRT and an SDVO connector since the SDVO connector would be initialised
with type 'unknown' and hence have its type_id assigned from the wrong pool.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Eric Anholt <eric@anholt.net>
