This patch addresses two problems:
1) Bulk reads should always use the DATA0 for the pid, and the write
PID should toggle between DATA0 and DATA1. The fix is using
dbgp_pid_write_update() and dbgp_pid_read_update().
2) The delay loop for waiting for a transaction was not long enough to
always complete the initial handshake inside dbgp_wait_until_done().
After the initial handshake the maximum delay length is never reached.
The combined result of these two changes allows for the removal of the
forced resynchronization where a bulk write was issued with a dummy
data payload only to get the device to start accepting data writes
again.
CC: Eric Biederman <ebiederm@xmission.com>
CC: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for USB serial interface provided by ViVOtech ViVOpay devices via
new driver vivopay-serial. Currently only the ViVOpay 8800 device is supported,
but support for similar devices can be added by adding the appropriate device
IDs to the driver.
Signed-off-by: Forest Bond <forest.bond@outpostembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding vbus_pin_inverted so that the usb detect pin can be active high
or low depending on HW implementation also replaced the
gpio_get_value(udc->vbus_pin); with a call to vbus_is_present(udc); This
allows the driver to be loaded and save about 0,15W on the consumption.
Signed-off-by: Eirik Aanonsen <eaa@wprmedical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A bunch of USB gadget drivers where never ported from the linux 2.4
series to 2.6 kernels. However there's some code still in the tree for
them which isn't used and is probably untested for ages.
As the chance of these drivers being forward ported is probably quite
small now it might be time to get rid of them.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
init_completion() hasn't been called yet and the thread isn't created
if we end up here, so don't call complete() on thread_notifier.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The lock must be dropped before usb_autopm_interface_put() is called
Signed-off-by: Oliver Neukum <oliver@neukum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes warning caused by calling min() macro
with arguments of different types:
drivers/usb/gadget/f_mass_storage.c:623: warning: \
comparison of distinct pointer types lacks a cast
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Marek Szyprowski <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The removed part always evaluates to false.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When the HDC driver writes the data to the transfer buffers it pollutes
the D-cache (unlike DMA drivers where the device writes the data). If
the corresponding pages get mapped into user space, there are no
additional cache flushing operations performed and this causes random
user space faults on architectures with separate I and D caches
(Harvard) or those with aliasing D-cache.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Matthew Dharm <mdharm-kernel@one-eyed-alien.net>
Cc: Greg KH <greg@kroah.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As Alan Cox have pinpointed the driver still required protection against
parallels calls to the config ioctl(). If lock is still necessary the use of
BKL is abused here. So replace BKL with a more convenient mutex.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The semaphore data->lock is semantically a mutex. Convert it to a real
mutex.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The mass storage function responded needlessly to a set
configuration packet. This was a leftover from converting
gadget (file storage gadget) into a composite function.
Moreover, it has failed to respond to get max LUN request.
Adding request queueing made the function work better.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds a fallback which forces all LUNs ejection (including
non-removable and with prevent_medium_removal flag) when mass storage
function (MSF) worker thread exits and gadget fails to handle the
situation.
Previously, if thread_exits was not specified mass storage function
(MSF) did nothing when exiting thread as it's unclear for *function*
what to do when it's thread terminates so responsibility of handling
this situation was left to the *gadget* using the function.
The g_mass_storage handled the situation by unregistering itself (the
same thing that file storage gadget does). However, g_multi did
nothing and so MSF did not eject LUNs which prevented file system
unmounting.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trying to use double buffer modes in RTL versions <2.0 may result in
infinite hangs or data corruption. So avoid them with older versions.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All current Blackfin parts are using RTL v1.9, but they don't expose the
hardware registers to probe this dynamically. So hardcode the version to
v1.9 for now.
Need to move the local hwvers related defines higher up in the header so
that sub-musb headers may utilize them.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As reported by Antonio, there are cases where the ep->lock
can be taken twice, triggering a deadlock.
The typical sequence is :
irq_handler
\
-> gadget.complete()
\
-> pxa27x_udc.pxa_ep_queue() : ep->lock is taken
\
-> gadget.complete()
\
-> pxa27x_udc.pxa_ep_queue() : ep->lock is taken
==> *deadlock*
The patch fixes this by :
- releasing the lock each time gadget.complete() is called
- adding a check in handle_ep() to detect a recursive call,
in which case the function becomes on no-op.
The patch is still not good enough for ep0. For this unique
endpoint, another well thought over patch will be needed.
Reported-by: Antonio Ospite <ospite@studenti.unina.it>
Tested-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the serial port on devices based on the MosChip 7715,
which provides a serial and parallel port on a single usb interface.
This is added to the existing driver for the Moschip 7720 dual serial
port device. The 7715 is very similiar to the 7720, requiring only the
addition of a calc_num_ports() function, a separate interrupt-in
endpoint callback, and some manipulation of the port pointers added to
the attach() function to correct the fact that the usbserial core
erroneously assigns the first bulk in/out endpoint pair to the serial
port (the 7715 uses these for its parallel port). There is no support
for the 7715's parallel port yet.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold points out that get_string() is basically just a
re-implimentation of usb_string(). It is also buggy. It does DMA on
the stack and it doesn't handle negative returns from
usb_get_descriptor(). Plus unicode_to_ascii() is a rubbish function and
moving to usb_string() avoids using it.
Let's eliminate get_string() entirely.
Reported-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This replaces deprecated dma_sync_single() with dma_sync_single_for_cpu().
There is no functional change because dma_sync_single() simply calls
dma_sync_single_for_cpu():
static inline void __deprecated dma_sync_single(struct device *dev,
dma_addr_t addr, size_t size,
enum dma_data_direction dir)
{
dma_sync_single_for_cpu(dev, addr, size, dir);
}
This fixes the following compile warnings:
drivers/usb/gadget/s3c-hsotg.c: In function 's3c_hsotg_unmap_dma':
drivers/usb/gadget/s3c-hsotg.c:376: warning: 'dma_sync_single' is deprecated (declared at /home/fujita/git/linux-2.6/include/linux/dma-mapping.h:109)
drivers/usb/gadget/s3c-hsotg.c: In function 's3c_hsotg_map_dma':
drivers/usb/gadget/s3c-hsotg.c:758: warning: 'dma_sync_single' is deprecated (declared at /home/fujita/git/linux-2.6/include/linux/dma-mapping.h:109)
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
we were printing the info about musb probe too early where
it was still possible for things to go wrong. Move the
down right before the return 0 statement. While at that
also convert pr_info to dev_info.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
when probe() fails, we should iounmap() the mapped address.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
... and even added a flag to struct musb, so let's
use that.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
we have those addresses already ioremaped, so let's
use our __raw_readl/writel wrappers.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding support for MUSB register save and restore during system
suspend and resume.
Changes:
- Added musb_save/restore_context() functions
- Added platform specific musb_platform_save/restore_context()
to handle platform specific jobs.
- Maintaining BlackFin compatibility by adding read/write
functions for registers which are not available in BlackFin
Tested system suspend and resume on OMAP3EVM board.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The configuration Option USB_HCD_DMA is not reachable in KConfig so
this piece of Code is effectively dead and useless. Remove it to avoid
confusion.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Uses the new snoop function from commit 4c6e8971cb,
but includes the buffer data where appropriate, as before.
Signed-off-by: Chris Frey <cdfrey@foursquare.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- correct spelling/whitespace in ftdi_sio.h and ftdi_sio_ids.h
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The variables priv and portdata are initialized twice to the same (side
effect-free) expressions. Drop one initialization in each case.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@forall@
idexpression *x;
identifier f!=ERR_PTR;
@@
x = f(...)
... when != x
(
x = f(...,<+...x...+>,...)
|
* x = f(...)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The problem with Ethernet based networking devices is to clearly
identify what's their usage. Special interfaces like bridges, WiFi,
Bluetooth, WiMAX or WWAN are already using DEVTYPE identification.
This patch marks the Ethernet functions of gadgets from the device
type "gadget". Automatic setup of these interfaces can now happen
from userspace without the need of hardcoding the network interface
name.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Barry project's userspace program, bcharge, can better handle this
device and functionality, and it also works with the latest phones,
which this driver does not support. So remove it, as the userspace code
should be used instead.
Cc: Chris Frey <cdfrey@foursquare.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Total removal from the ioctl code path except for the outcall
to external modules. Locking is ensured by the normal locks
of usbfs.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL was not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL was not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL was not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL was not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL was not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL was not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver had used BKL to guard against disconnect but
was incorrectly converted leaving an SMP race.
BKL was added to disconnect() to fix this race
BKL was removed from ioctl() as the mutex is sufficient
on its own.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL was not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This pushes BKL down in ioctl handling and drops it
for some important ioctls
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace it by
mutex_lock(&file->f_dentry->d_inode->i_mutex);
following the example of the generic method
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Locking had long been changed making BKL redundant.
Simply remove it.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace BKL with usbfs_mutex to protect a global counter
and a per file data structure
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 4G XS Stick W14 seems to not understand RTS/DTR setting in
option_send_setup causing long timeouts on any open() which disturbs a
lot of well-known userspace applications like minicom or ModemManager.
Therefore, we enable OPTION_BLACKLIST_SENDSETUP blacklisting for it.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As suggested by Matthias Urlichs, this patch adds a somehow generic
mechanism for special handling of devices which don't support all bits
expected by this driver.
The blacklisting code is heavily stolen from sierra.c, but extended to
support different special cases.
For now, one case is implemented (OPTION_BLACKLIST_SENDSETUP), targeted
at the 4G W14 device: devices which don't understand the setting of
RTS/DTR in option_send_setup() causing a USB timeout of 5 s in any
userspace open() which leads to errors in most userspace applications.
In addition, I prepared another case for devices with interfaces which
shall not be accessed by this driver (targeted at the D-Link DWM 652).
However, OPTION_BLACKLIST_RESERVED_IF is not fully implemented yet as I
have no device to test this. Anyone volunteering to help here? If not,
I'll contact the guys who added D-Link DWM 652 support soon.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Carsten Juttner thankfully investigated a bit and found out some details
about the chipset used in the 4G W14 device I recently added to
option.c.
I think this information is useful for reference, so I'd be happy if you
could include those bits.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The id_table field of the struct pci_driver is constant in <linux/pci.h>
so it is worth to make pci_ids also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The match_table field of the struct of_device_id is constant in <linux/of_platform.h>
so it is worth to make ace_of_match also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The match_table field of the struct of_device_id is constant in <linux/of_platform.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Test whether tusb_dma is not NULL before dereferencing
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: Move hcd free_dev call into usb_disconnect
I found a way to oops the kernel:
1. Open a USB device through devio.
2. Remove the hcd module in the host kernel.
3. Close the devio file descriptor.
The problem is that closing the file descriptor does usb_release_dev
as it is the last reference. usb_release_dev then tries to invoke
the hcd free_dev function (or rather dereferencing the hcd driver
struct). This causes an oops as the hcd driver has already been
unloaded so the struct is gone.
This patch tries to fix this by bringing the free_dev call earlier
and into usb_disconnect. I have verified that repeating the
above steps no longer crashes with this patch applied.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When hardware is removed on a Stratus, the system may crash like this:
ACPI: PCI interrupt for device 0000:7c:00.1 disabled
Trying to free nonexistent resource <00000000a8000000-00000000afffffff>
Trying to free nonexistent resource <00000000a4800000-00000000a480ffff>
uhci_hcd 0000:7e:1d.0: remove, state 1
usb usb2: USB disconnect, address 1
usb 2-1: USB disconnect, address 2
Unable to handle kernel paging request at 0000000000100100 RIP:
[<ffffffff88021950>] :uhci_hcd:uhci_scan_schedule+0xa2/0x89c
#4 [ffff81011de17e50] uhci_scan_schedule at ffffffff88021918
#5 [ffff81011de17ed0] uhci_irq at ffffffff88023cb8
#6 [ffff81011de17f10] usb_hcd_irq at ffffffff801f1c1f
#7 [ffff81011de17f20] handle_IRQ_event at ffffffff8001123b
#8 [ffff81011de17f50] __do_IRQ at ffffffff800ba749
This occurs because an interrupt scans uhci->skelqh, which is
being freed. We do the right thing: disable the interrupts in the
device, and do not do any processing if the interrupt is shared
with other source, but it's possible that another CPU gets
delayed somewhere (e.g. loops) until we started freeing.
The agreed-upon solution is to wait for interrupts to play out
before proceeding. No other bareers are neceesary.
A backport of this patch was tested on a 2.6.18 based kernel.
Testing of 2.6.32-based kernels is under way, but it takes us
forever (months) to turn this around. So I think it's a good
patch and we should keep it.
Tracked in RH bz#516851
Signed-Off-By: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1329) converts the USB stack over to the PM core's
runtime PM framework. This involves numerous changes throughout
usbcore, especially to hub.c and driver.c. Perhaps the most notable
change is that CONFIG_USB_SUSPEND now depends on CONFIG_PM_RUNTIME
instead of CONFIG_PM.
Several fields in the usb_device and usb_interface structures are no
longer needed. Some code which used to depend on CONFIG_USB_PM now
depends on CONFIG_USB_SUSPEND (requiring some rearrangement of header
files).
The only visible change in behavior should be that following a system
sleep (resume from RAM or resume from hibernation), autosuspended USB
devices will be resumed just like everything else. They won't remain
suspended. But if they aren't in use then they will naturally
autosuspend again in a few seconds.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1328) reorders the functions in drivers/usb/core/driver.c
so as to put all the routines dependent on CONFIG_PM in one place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1327) changes the way negative autosuspend delays
prevent device from autosuspending. The current code checks for
negative values explicitly in the autosuspend_check() routine. The
updated code keeps things from getting that far by using
usb_autoresume_device() to increment the usage counter when a negative
delay is set, and by using usb_autosuspend_device() to decrement the
usage counter when a non-negative delay is set.
This complicates the set_autosuspend() attribute method code slightly,
but it will reduce the overall power management overhead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1326) adds usb_enable_autosuspend() and
usb_disable_autosuspend() routines for use by drivers. If a driver
knows that its device can handle suspends and resumes correctly, it
can enable autosuspend all by itself. This is equivalent to the user
writing "auto" to the device's power/level attribute.
The implementation differs slightly from what it used to be. Now
autosuspend is disabled simply by doing usb_autoresume_device() (to
increment the usage counter) and enabled by doing
usb_autosuspend_device() (to decrement the usage counter).
The set_level() attribute method is updated to use the new routines,
and the USB Power-Management documentation is updated.
The patch adds a usb_enable_autosuspend() call to the hub driver's
probe routine, allowing the special-case code for hubs in quirks.c to
be removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1325) changes the locking for the persist_enabled flag
in struct usb_device. Now it is protected by the device lock, along
with all its neighboring bit flags, instead of the PM lock (which is
about to vanish anyway).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1324) makes a small change to the code used for remote
wakeup of root hubs. hcd_resume_work() now calls the hub driver's
remote-wakeup routine instead of implementing its own version.
The patch is complicated by the need to rename remote_wakeup() to
usb_remote_wakeup(), make it non-static, and declare it in a header
file. There's also the additional complication required to make
everything work when CONFIG_PM isn't set; the do-nothing inline
routine had to be moved into the header file.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1323) changes the locking requirements for
usb_autosuspend_device(), usb_autoresume_device(), and
usb_try_autosuspend_device(). This isn't a very important change;
mainly it's meant to make the locking more uniform.
The most tricky part of the patch involves changes to usbdev_open().
To avoid an ABBA locking problem, it was necessary to reduce the
region protected by usbfs_mutex. Since that mutex now protects only
against simultaneous open and remove, this posed no difficulty -- its
scope was larger than necessary.
And it turns out that usbfs_mutex is no longer needed in
usbdev_release() at all. The list of usbfs "ps" structures is now
protected by the device lock instead of by usbfs_mutex.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1322) reverses the two outcomes of an "if" statement in
usb_probe_interface(), to avoid an unnecessary level of indentation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB devices do not have to sort interfaces in their descriptors based on
the interface number, and they may choose to skip interface numbers. The
USB bandwidth allocation code for installing a new configuration assumes
the for loop variable will match the interface number. Make it use the
interface number (bInterfaceNumber) in the descriptor instead.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enable the SD-Card interface on multiple Option 3G sticks.
The unusual_devs.h entry is necessary because the device descriptor is
vendor-specific. That prevents usb-storage from binding to it as an interface
driver.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
g_nokia is the gadget driver implementing
WMCDC Wireless Handset Control Model for the N900
device.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Dunlap reported this error when compiling the xHCI driver:
linux-next-20100104/drivers/usb/host/xhci.h:1214:
sorry, unimplemented: inlining failed in call to 'xhci_get_slot_state': function body not available
The xhci_get_slot_state() function belongs in xhci-dbg.c, since it
involves debugging internal xHCI structures. However, it is only used in
xhci-hcd.c. Some toolchains may have issues since the inlined function
body is not in the xhci.h header file. Remove the inline keyword to avoid
this.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
urb_priv->tds has type struct td **, not struct td *, so the
elements of the array should have pointer type, not structure type.
Convert kzalloc to kcalloc as well.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@disable sizeof_type_expr@
type T;
T **x;
@@
x =
<+...sizeof(
- T
+ *x
)...+>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original code was passing a stack variable as a dma buffer, so I
made it an allocated variable. Instead of adding a bunch of kfree()
calls, I changed all the error return paths to gotos.
Also I noticed that the error checking wasn't correct because
usb_get_descriptor() can return negative values.
While I was at it, I made an unrelated white space change by moving
the unicode_to_ascii() on to one line.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill string that is allocated and generated using speed and parity
settings but is never used (and never has been).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change data-argument type from (void *) to (u8 *) to prevent endianess
problems.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OMAP3 has three HS USB ports so it can have three different regulator
for each PHY connected to each port.
Currently these regulators are assumed to be optional and driver doesn't
fail but continue with the initialization if it doesn't get any regulators.
Regulator supply names has to be mapped in board files as 'hsusbN' where
'N' is port number and can be {0, 1 ,2}.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of the board might use external Vbus power supply on musb
interface which would require to program ULPI_BUSCONTROL register.
Adding 'extvbus' flag which can be set from such boards which will
be checked at musb driver files before programming ULPI_BUSCONTROL.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Save dynamic FIFO read only information for later uses during
musb_save/restore_context functions.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB's programming guide dictates how we should handle its
irqs and in which order. Follow that.
Signed-off-by: Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The version applied had a few comments which are now
done.
Thanks to Sergei for pointing out.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the Tx abort/teardown logic. We now wait for the teardown
completion interrupt and acknowledge the same by setting the tx_complete
register to 0.
This change is needed to ensure that abort processing works on DM365 platform.
Without this change after completion of abort processing the system is
overwhelmed with continuous stream of abort interrupts.
This change has been tested on all CPPI3.x platforms (DM644x, DM646x, DM35x,
DM36x).
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements the work around for a Mentor controller related
bug where it's observed a BULK Tx toggle error on the bus when a
BULK IO gets scheduled on an endpoint that was earlier used for
handling ISOC transaction and needed to start on 1 toggle. When such
a situation arises even if the TXCSR toggle bits are programmed
correctly by the musb driver the data gets transmitted with 0 toggle
which leads to toggle error on the bus and the BULK transaction fails.
In case of MSC write, the device gets reset by the Host.
This Mentor bug is observed on almost all Mentor versions (1.3, 1.5,
1.8). Confirmed on DM644x, DM355, DM365, OMAPL13x platforms.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB DMA_INTR register may sometimes read zero when infact there
was a pending interrupt. Workaround this by reading the DMA_COUNT
values for all enabled channels when this condition occurs.
Flag these channels as the ones needing to be serviced.
Additionally, the absence of a debug print meant we would never
catch a spurious DMA interrupt in MUSB. So this patch adds a
debug print in the IRQ handler.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a wrapper for reading the DMA count register, analogous
to the one for writing to this register.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have observed MSC data read corruption when USB LAN device is
also connected and it's interface is up.
Silicon team has confirmed an errata where in all the active
transfers should use FIFO space either in first 8K or next 8K.
So far we have observed the issue in above use case scenario.
As a workaround to it, adding a new FIFO config (5) fitting well
within first 8K which can be used for such use cases.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
move to request_threaded_irq() on twl4030 children.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Under the new system a device cannot be suspended against
the driver's wish. Therefore this condition no longer needs
to be checked for.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Return values are being initialised to zero only to be unconditionally
assigned to a few instructions later. This may give the impression that
zero is returned on success, which is not the case.
Note also that ftdi_NDI_device_setup never reports errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also remove unnecessary buffer allocations for zero-length transfers.
Reported-by: Matti Aarnio <matti.aarnio@zmailer.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also fixes DMA transfer to stack for latency buffer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's really the wireless speed, so rename the thing to make
more sense. Based on a recommendation from David Vrabel
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently a non-root-hub USB device's wakeup settings are initialized when the
device is set to a configured state using device_init_wakeup(), but this is not
correct as wakeup is split into "capable" (can_wakeup) and "enabled"
(should_wakeup). The settings should be initialized instead in the device
initialization (usb_new_device) with the "capable" setting disabled and the
"enabled" setting enabled. The "capable" setting should be set based on the
device being configured or unconfigured, and "enabled" setting set based on
the sysfs power/wakeup control.
This patch retains the sysfs power/wakeup setting of a non-root-hub USB device
over a USB device re-configuration, which can happen (for example) after a
suspend/resume cycle.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pbLua console port is known to not be a modem, so it is
unnecessary to be told this when it is plugged in.
Add NOT_A_MODEM quirk to tell the driver that we know this already
and hence not to warn us, and mark the pbLua console port.
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pbLua firmware (http://pblua.com/) for the Lego Mindstorms NXT
provides a CDC ACM port for it's serial console.
This used to be detected automatically, but this support has been
dropped, probably for sensible reasons.
Explicitly add support for this device by adding an item to the
device ID table.
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to a simple oversight when bus zero was added, the text API fails to
deliver the bus number in 'E' messages (which are equivalent of 'C'
messages, only for error case). This makes it harder, for instance,
use a search-and-highlight in a text editor. So fix it.
Also, Alan Stern requested adding timestamps to 'E' messages. This is
purely cosmetic, but makes it easier to read the trace. This is done
for both text and binary APIs.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it's easier to keep up and add more sysfs entries
as necessary.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Normally, the musb uses ep1 as the bidirectional bulk endpoint. This won't
work on the Blackfin musb as all endpoints (except ep0) are unidirectional.
Further, ep1-ep4 have a small 128 byte FIFO which makes them undesirable
for bulk endpoints (which need more like a 512 byte FIFO). This leaves us
with ep5-ep7 which have 1024 byte FIFOs and can be configured as either
in/out and bulk/interrupt/iso on the fly.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've got a crappy cypress converter here, and while running at higher
baud rates craps out on throughput, it works fine with lower ones.
While it'd be nice to simply use a lower baud rate, not all devices
can be configured this way, and it is possible to (slowly) interact
at higher rates by sending a byte at a time. So let people force
higher rates when they need it via a module parameter.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current code has a confusing duplicate new_baudrate init when setting
the serial parameters. So just combine the if statement checks to avoid
this.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB_SERIAL_DEBUG Kconfig is for the USB serial debug driver, not for
generically enabling debug output in random USB serial drivers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices which use mode switching revert to their
primary mode as they are reset. They must not be reset for
error handling. As user spaces makes the switch it also
has to tell the kernel that a device is quirky.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices must be switched to a new mode to fully use them.
A reset would make them revert to the old mode. Therefore a reset
must not be used for error handling with such devices.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it's expected that the transceiver driver will
initialize and call the notifier chain when
necessary. Implement that for twl4030-usb driver.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An incorrect sizeof() resulted in only 4 (or 8) octets of the CHID being
checked instead of all 16 octets. A randomly generated CHID had a
probability of being unable to start a WUSB host of less than 1 in
2 billion.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xhci_add_endpoint() is used in the reset path. It must
use GFP_NOIO to avoid a possible deadlock.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update cdc-acm to the async methods eliminating the workqueue
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use platform_get_resource() to fetch the memory resource and
resource_size() for calculate the length.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EHCI FSL controller preserve its state during sleep mode, so nothing
fancy needs to be done.
Though, during 'deep sleep' mode (as found in MPC831x CPUs) the
controller turns off and needs to be reinitialized upon resume.
This patch adds support for hibernation and resuming after deep sleep.
Based on Dave Liu and Jerry Huang's work[1].
[1] http://www.bitshrine.org/gpp/linux-fsl-2.6.24.3-MPC8315ERDB-usb-power-mangement.patch
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes following warnings:
ehci-fsl.c:43:5: warning: symbol 'usb_hcd_fsl_probe' was not declared. Should it be static?
ehci-fsl.c:150:6: warning: symbol 'usb_hcd_fsl_remove' was not declared. Should it be static?
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fix audio record functionality for some Full speed sound blaster devices.
Issue: Sometimes transaction complete indication is coming from HW one frame later.
Solution: If scan_periodic process now frame or previous frame now-1 and sitd transaction
is not finished yet, exit scan_periodic function and check the same transaction in the next frame.
Signed-off-by: Dimitry Epshtein <dima@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sometimes disable_periodic() stop scan_periodic before than free_cached_itd_list() was called.
In such case USB Host stacked during disconnect operation
Solution: add call of free_cached_itd_list() function in disable_periodic()
Signed-off-by: Dimitry Epshtein <dima@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a new host controller driver method, reset_device(), that the USB core
will use to notify the host of a successful device reset. The call may
fail due to out-of-memory errors; attempt the port reset sequence again if
that happens. Update hub_port_init() to allow resetting a configured
device.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a USB device is reset, the xHCI hardware must know, in order to match
the device state and disable all endpoints except control endpoint 0.
Issue a Reset Device command after a USB device is successfully reset.
Wait on the command to finish, and then cache or free the disabled
endpoint rings.
There are four different USB device states that the xHCI hardware tracks:
- disabled/enabled - device connection has just been detected,
- default - the device has been reset and has an address of 0,
- addressed - the device has a non-zero address but no configuration has
been set,
- configured - a set configuration succeeded.
The USB core may issue a port reset when a device is in any state, but the
Reset Device command will fail for a 0.96 xHC if the device is not in the
addressed or configured state. Don't consider this failure as an error,
but don't free any endpoint rings if this command fails.
A storage driver may request that the USB device be reset during error
handling, so use GPF_NOIO instead of GPF_KERNEL while allocating memory
for the Reset Device command.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the hub emulation code to allow ports on an xHCI root hub to be
disabled. Add the code to clear the port enabled/disabled bit, and clear
the port enabled/disabled change bit. Like EHCI, the port cannot be
enabled by setting the port enabled/disabled bit. Instead, a port is
enabled by the host controller after a reset.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor the code to clear the port change bits in the port status
register. All port status change bits are write one to clear.
Remove a redundant port status read that was supposed to unblock any
posted writes. We read the port after the write to get the updated status
for debugging, so the port read after that is unnecessary.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All commands that can be issued to the xHCI hardware can come back with
vendor-specific "informational" completion codes. These are to be treated
like a successful completion code. Refactor out the code to test for the
range of these codes and print debugging messages.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xhci_command structure is the basic structure for issuing commands to
the xHCI hardware. It contains a struct completion (so that the issuing
function can wait on the command), command status, and a input context
that is used to pass information to the hardware. Not all commands need
the input context, so make it optional to allocate. Allow
xhci_free_container_ctx() to be passed a NULL input context, to make
freeing the xhci_command structure simple.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor out the code to cache or free endpoint rings from recently
dropped or disabled endpoints. This code will be used by a new function
to reset a device and disable all endpoints except control endpoint 0.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we fail to queue an evaluate context command or a configure endpoint
command to the command ring in xhci_configure_endpoint(), we need to
remove the xhci_command structure from the device's command list before
returning. If the command is left on the command list, it will sit there
indefinitely, blocking commands submitted after this fails.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1316) adds some error checking to usb_submit_urb().
It's conditional on CONFIG_USB_DEBUG, so it won't affect normal users.
The new check makes sure that the actual type of the endpoint
described by urb->pipe agrees with the type encoded in the pipe value.
The USB error code documentation is updated to include the code
returned by the new check, and the usbfs SUBMITURB handler is updated
to use the correct pipe type when legacy user code tries to submit a
bulk transfer to an interrupt endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My distro kernel (Fedora Rawhide) started throwing warnings from DMA API
checker, so I have no choice but band-aid it quick. There's no attempt
to reuse DMA buffers. Control messages are only sent rarely anyway.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hardware reports wrong interrupt. Although such a situation should not
happen, the compiler complains about this access.
This patch adds a sanity check and generates warning to detect such
issues.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On various mxc boards, the intial ULPI reads resulted in a timeout
which prevented the transceiver to be identified and thus the ehci
device to be probed.
Initializing the hardware lines connected to the transceiver (through
pdata->init call) before actually enabling clocks and configuring
registers in the devices fixes this problem.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed CS5 and CS6 from data bits since these are not supported
in FTDI hardware.
Signed-off-by: Mark J. Adamson <mark.adamson@ftdichip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Latency timeout was read but never stored on port probe. When
ASYNC_LOW_LATENCY was cleared the device timeout would get set to 0
rather than the default 16ms.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We always push characters to ldisc immediately regardless of
ASYNC_LOW_LATENCY.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resubmitting read urb fails with -EPERM if completion handler runs while
urb is being killed on close. This should not be reported as an error.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Changes:
Return an empty string for modulation
when there is no connection
Fix sysfs unload race conditions
Log firmware load process, remove delay
Add new configuration interface
Remove cxacru-cf.bin
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This has never worked properly because wsize passed to
cxacru_cm() is incorrectly set to the number of values
instead of the data bytes. The maximum number of values
that can be set at once is 7 which means the device will
not get enough data to work with and none of the
configuration values will be used.
At least one existing cxacru-cf.bin file contains invalid
data which will prevent the modem from syncing properly.
Fixing it is likely to break existing systems, and the
new sysfs interface for setting configuration parameters
can provide the same functionality. A script is provided
to convert from the original format.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The modem can be configured using CM_REQUEST_CARD_DATA_SET,
although CM_REQUEST_CARD_DATA_GET does not return any data.
Tested by setting the modulation (0x0a) option.
There is a list of parameters in the following archive,
but the meaning of many of them is not well documented:
http://sourceforge.net/project/shownotes.php?release_id=301825
This source also indicates that the highest parameter set
is 0x4a but this varies by model so an arbitrary limit of
0x7f has been used (the index is a 32-bit integer).
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Firmware writing takes 256ms per 4KB with OHCI, which
is very slow compared to 7ms per 4KB with UHCI.
Until I have access to a hardware USB analyser it may
not be possible to determine why this happens.
Instead of appearing to do nothing, log progress when
writing firmware and then log the ATM device information
when finished. Remove an unnecessary 4 second delay.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These commands were found by accident... fortunately
it still works even if the flash memory is erased,
despite having no USB device IDs.
Some example sysfs code for raw command access:
http://simon.arlott.org/pub/cxacru/raw.c
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is possible for usb_get_intfdata() to return NULL if
sysfs is accessed while the module is being unloaded or
the device is being removed.
Move the access code to an inline function in usbatm.h,
and return -ENODEV if any of the pointers are NULL.
It should not be possible for the instance data or atm
device to be invalid until after unbind() completes and
the sysfs attributes have been removed.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When attempting to read data that is not actually
an array of values, the length may be negative
which causes an Oops due to a likely access off
the end of the data array.
This bug should not occur under normal use unless
the device returns an invalid response.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When there is no connection, return an empty string
instead of "0" for the connection modulation.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is a Full / Low speed only USB host for the i.MX21.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block: (38 commits)
block: don't access jiffies when initialising io_context
cfq: remove 8 bytes of padding from cfq_rb_root on 64 bit builds
block: fix for "Consolidate phys_segment and hw_segment limits"
cfq-iosched: quantum check tweak
blktrace: perform cleanup after setup error
blkdev: fix merge_bvec_fn return value checks
cfq-iosched: requests "in flight" vs "in driver" clarification
cciss: Fix problem with scatter gather elements in the scsi half of the driver
cciss: eliminate unnecessary pointer use in cciss scsi code
cciss: do not use void pointer for scsi hba data
cciss: factor out scatter gather chain block mapping code
cciss: fix scatter gather chain block dma direction kludge
cciss: simplify scatter gather code
cciss: factor out scatter gather chain block allocation and freeing
cciss: detect bad alignment of scsi commands at build time
cciss: clarify command list padding calculation
cfq-iosched: rethink seeky detection for SSDs
cfq-iosched: rework seeky detection
block: remove padding from io_context on 64bit builds
block: Consolidate phys_segment and hw_segment limits
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (252 commits)
ASoC: Check progress when reporting periods from i.MX FIQ handler
ASoC: Remove a unused variables from i.MX FIQ runtime data
ALSA: hda - Add/fix ALC269 FSC and Quanta models
ALSA: hda - Add ALC670 codec support
OMAP4: PMIC: Add support for twl6030 codec
ALSA: hda - remove unnecessary msleep on power state transitions
usb/gadget/{f_audio,gmidi}.c: follow recent changes in audio.h
ASoC: fsi: Modify over/under run error settlement
ASoC: OMAP4: Add McPDM platform driver
ASoC: OMAP4: Add support for McPDM
ASoC: OMAP: data_type and sync_mode configurable in audio dma
ALSA: hda - Add missing description in HD-Audio-Models.txt
ALSA: add support for Macbook Air 2,1 internal speaker
ALSA: usbaudio: consolidate header files
ALSA: usbmixer: bail out early when parsing audio class v2 descriptors
ALSA: usbaudio: implement basic set of class v2.0 parser
ALSA: usbaudio: introduce new types for audio class v2
ALSA: usbaudio: parse USB descriptors with structs
ALSA: hda - enable snoop for Intel Cougar Point
ALSA: hda - Remove identical definitions for macmini3 model
...
Set power.async_suspend for USB devices, endpoints and interfaces,
allowing them to be suspended and resumed asynchronously during
system sleep transitions.
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1331) adds non-tree ordering constraints needed for
proper resume of PCI USB host controllers from hibernation. The main
issue is that non-high-speed devices must not be resumed before the
high-speed root hub, because it is the ehci_bus_resume() routine which
takes care of handing the device connection over to the companion
controller. If the device resume is attempted before the handover
then the device won't be found and it will be treated as though it had
disconnected.
The patch adds a new field to the usb_bus structure; for each
full/low-speed bus this field will contain a pointer to the companion
high-speed bus (if one exists). It is used during normal device
resume; if the hs_companion pointer isn't NULL then we wait for the
root-hub device on the hs_companion bus.
A secondary issue is that an EHCI controlller shouldn't be resumed
before any of its companions. On some machines I have observed
handovers failing if the companion controller is reinitialized after
the handover. Thus, the EHCI resume routine must wait for the
companion controllers to be resumed.
The patch also fixes a small bug in usb_hcd_pci_probe(); an error path
jumps to the wrong label, causing a memory leak.
[rjw: Fixed compilation for CONFIG_PM_SLEEP unset.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The five-second delay can be rather annoying, and makes the system
appear much less responsive when you connect a USB drive.
It's also not entirely clear that it is needed - the settling delay has
at least historically been an issue on some Apple iPods, for example,
and some devices have been reported to need even more than the old 5s
delay.
But before we penalize them all, let's see how bad it really is. Some
of the reasons for long delays seem to be actual historical kernel bugs
that should probably never have been papered over with a delay in the
first place (there's a Ubuntu bug report for 2.6.20 about a NULL pointer
dereference unless 'delay_use' is 8 or more, for example).
It also looks like some distros have already shipped with delay_use=0,
so the five second default may well be totally historical.
In other words: "Let's see if anybody screams".
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.
Also introduce a temporary wrapper for backwards compability. This can
be removed after the merge window is closed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Some structs in linux/usb/audio.h have got new names to mark them as
part of version 1.0 of the USB audio standard. Follow these changes
in the gadget drivers.
Note that this header and the ALSA USB driver will undergo some
refactoring soon, so there might be another update to the gadgets as
well.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
eem_wrap() is sending a sentinel CRC, but it didn't indicate that to
the host, it should zero bit 14 (bmCRC) in the EEM packet header,
instead of setting it.
Also remove a redundant crc calculation in eem_unwrap().
Signed-off-by: Steve Longerbeam <stevel@netspectrum.com>
Acked-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With CONFIG_USB_ULPI=y, CONFIG_USB<=m, CONFIG_PCI=n and
CONFIG_USB_OTG_UTILS=n, which is the default used for mx31moboard,
the build for all mx3 platforms fails because drivers/usb/otg/ulpi.c
where otg_ulpi_create is defined is not compiled.
Build error:
arch/arm/mach-mx3/built-in.o: In function `mxc_board_init':
kzmarm11.c:(.init.text+0x73c): undefined reference to `otg_ulpi_create'
kzmarm11.c:(.init.text+0x1020): undefined reference to `otg_ulpi_create'
This isn't a strong dependency as drivers/usb/otg/ulpi.c doesn't
use functions defined in drivers/usb/otg/otg.o and is only needed
to get ulpi.o linked into the kernel image.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
g_multi used CONFIG_USB_ETH_RNDIS to check if RNDIS option was requested
where it should check for CONFIG_USB_G_MULTI_RNDIS. As a result, RNDIS
was never present in g_multi regardless of configuration.
This fixes changes made in commit 396cda90d2.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After kfifo rework FHCI fails to build:
CC drivers/usb/host/fhci-tds.o
drivers/usb/host/fhci-tds.c: In function 'fhci_ep0_free':
drivers/usb/host/fhci-tds.c:108: error: used struct type value where scalar is required
drivers/usb/host/fhci-tds.c:118: error: used struct type value where scalar is required
drivers/usb/host/fhci-tds.c:128: error: used struct type value where scalar is required
This is because kfifos are no longer pointers in the ep struct.
So, instead of checking the pointers, we should now check if kfifo
is initialized.
Reported-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for Dell Computer Corp. Wireless 5720 VZW Mobile
Broadband (EVDO Rev-A) Minicard GPS Port. I stole the name from lsusb,
but my card does not have a GPS on it (at least not that I can make
function). I'm sure the patch is whitespace damaged but the one line
addition should be fairly straightforward nonetheless.
Tested-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the USB product ID of KAIREN's USB VGA Adaptor,
USB20SVGA-MB-PLUS, to sisusbvga work with it.
Signed-off-by: Tanaka Akira <akr@fsij.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1. There are two msleep calls inside two spin lock sections, need to unlock
and lock again after msleep.
2. Save a extra status reg setting.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB gadget controller drivers normally export their driver registration
function, allowing modular builds of the individual gadget drivers so
do so for s3c-hsotg, fixing builds.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
