If the remote device is not present, the connections attemp fails and
the struct hci_conn was not freed
Signed-off-by: Tomas Targownik <ttargownik@geicp.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
PTS test A2DP/SRC/SRC_SET/TC_SRC_SET_BV_02_I revealed that
( probably after the df3c3931e commit ) the l2cap connection
could not be established in case when the "Auth Complete" HCI
event does not arive before the initiator send "Configuration
request", in which case l2cap replies with "Command rejected"
since the channel is still in BT_CONNECT2 state.
Based on patch from: Ilia Kolomisnky <iliak@ti.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Partial revert of commit aabf6f89. When the hidp session thread
was converted from kernel_thread to kthread, the atomic/wakeups
were replaced with kthread_stop. kthread_stop has blocking semantics
which are inappropriate for the hidp session kthread. In addition,
the kthread signals itself to terminate in hidp_process_hid_control()
- it cannot do this with kthread_stop().
Lastly, a wakeup can be lost if the wakeup happens between checking
for the loop exit condition and setting the current state to
TASK_INTERRUPTIBLE. (Without appropriate synchronization mechanisms,
the task state should not be changed between the condition test and
the yield - via schedule() - as this creates a race between the
wakeup and resetting the state back to interruptible.)
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
A remote user can provide a small value for the command size field in
the command header of an l2cap configuration request, resulting in an
integer underflow when subtracting the size of the configuration request
header. This results in copying a very large amount of data via
memcpy() and destroying the kernel heap. Check for underflow.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
In hci_conn_security ( which is used during L2CAP connection
establishment ) test for HCI_CONN_ENCRYPT_PEND state also
sets this state, which is bogus and leads to connection time-out
on L2CAP sockets in certain situations (especially when
using non-ssp devices )
Signed-off-by: Ilia Kolomisnky <iliak@ti.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When authentication completes we shouldn't blindly accept any pending
L2CAP connect requests. If the socket has the defer_setup feature
enabled it should still wait for user space acceptance of the connect
request. The issue only happens for non-SSP connections since with SSP
the L2CAP Connect request may not be sent for non-SDP PSMs before
authentication has completed successfully.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
With older userspace versions (using hciops) it might not have the
key type to check if the key has sufficient security for any security
level so it is necessary to check the return of hci_conn_auth to make
sure the connection is authenticated
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Some old hci controllers do not accept any mask so leave the
default mask on for these devices.
< HCI Command: Set Event Mask (0x03|0x0001) plen 8
Mask: 0xfffffbff00000000
> HCI Event: Command Complete (0x0e) plen 4
Set Event Mask (0x03|0x0001) ncmd 1
status 0x12
Error: Invalid HCI Command Parameters
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Tested-by: Corey Boyle <corey@kansanian.com>
Tested-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
shutdown should wait for SCO link to be properly disconnected before
detroying the socket, otherwise an application using the socket may
assume link is properly disconnected before it really happens which
can be a problem when e.g synchronizing profile switch.
Signed-off-by: Luiz Augusto von Dentz <luiz.dentz-von@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Structures "l2cap_conninfo" and "rfcomm_conninfo" have one padding
byte each. This byte in "cinfo" is copied to userspace uninitialized.
Signed-off-by: Filip Palian <filip.palian@pjwstk.edu.pl>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Ignacy reports that sometimes after leaving an IBSS
joining a new one didn't work because there still
were stations on the list. He fixed it by flushing
stations when attempting to join a new IBSS, but
this shouldn't be happening in the first case. When
I looked into it I saw a race condition in teardown
that could cause stations to be added after flush,
and thus cause this situation. Ignacy confirms that
after applying my patch he hasn't seen this happen
again.
Reported-by: Ignacy Gawedzki <i@lri.fr>
Debugged-by: Ignacy Gawedzki <i@lri.fr>
Tested-by: Ignacy Gawedzki <i@lri.fr>
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When one of the SSID's length passed in a scan or sched_scan request
is larger than 255, there will be an overflow in the u8 that is used
to store the length before checking. This causes the check to fail
and we overrun the buffer when copying the SSID.
Fix this by checking the nl80211 attribute length before copying it to
the struct.
This is a follow up for the previous commit
208c72f4fe, which didn't fix the problem
entirely.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 1d38c16ce4.
The mac80211 maintainer raised complaints about abuse of the CSA stop
reason, and about whether this patch actually serves its intended
purpose at all.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This partially reverts 1c5cae815d, because
the netdev name is copied into sdata->name, which is used for debugging
messages, for example. Otherwise, we get messages like this:
wlan%d: authenticated
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
read_lock() ... read_unlock_bh() is clearly bogus.
This was broken by
commit 23691d75cd
Author: Gustavo F. Padovan <padovan@profusion.mobi>
Date: Wed Apr 27 18:26:32 2011 -0300
Bluetooth: Remove l2cap_sk_list
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 0a35d36 ("cfg80211: Use capability info to detect mesh beacons")
assumed that probe response with both ESS and IBSS bits cleared
means that the frame was sent by a mesh sta.
However, these capabilities are also being used in the p2p_find phase,
and the mesh-validation broke it.
Rename the WLAN_CAPABILITY_IS_MBSS macro, and verify that mesh ies
exist before assuming this frame was sent by a mesh sta.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ingo Molnar noticed that we have this unnecessary ratelimit.h
dependency in linux/net.h, which hid compilation problems from
people doing builds only with CONFIG_NET enabled.
Move this stuff out to a seperate net/net_ratelimit.h file and
include that in the only two places where this thing is needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Several crashes in cleanup_once() were reported in recent kernels.
Commit d6cc1d642d (inetpeer: various changes) added a race in
unlink_from_unused().
One way to avoid taking unused_peers.lock before doing the list_empty()
test is to catch 0->1 refcnt transitions, using full barrier atomic
operations variants (atomic_cmpxchg() and atomic_inc_return()) instead
of previous atomic_inc() and atomic_add_unless() variants.
We then call unlink_from_unused() only for the owner of the 0->1
transition.
Add a new atomic_add_unless_return() static helper
With help from Arun Sharma.
Refs: https://bugzilla.kernel.org/show_bug.cgi?id=32772
Reported-by: Arun Sharma <asharma@fb.com>
Reported-by: Maximilian Engelhardt <maxi@daemonizer.de>
Reported-by: Yann Dupont <Yann.Dupont@univ-nantes.fr>
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's currently exposed only through /proc which, besides requiring
screen-scraping, doesn't allow userspace to distinguish between two
identical ATM adapters with different ATM indexes. The ATM device index
is required when using PPPoATM on a system with multiple ATM adapters.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: David Woodhouse <dwmw2@infradead.org>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 79f460ca49 add a duplicate
linux/slab.h include to net/mac80211/scan.c - remove it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
local->ps_data wasn't cleared on disassociation, which
(in some corner cases) caused reconnections to enter
psm before association completed.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ip_vs was adapted to netns the ftp application was not adapted
in a correct way.
However this is a fix to avoid kernel errors. In the long term another solution
might be chosen. I.e the ports that the ftp appl, uses should be per netns.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Stop tx queues before updating rate control to ensure
proper rate selection. Otherwise packets can be transmitted
in 40 Mhz whereas hw is configured in HT20.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In both trigger_scan and sched_scan operations, we were checking for
the SSID length before assigning the value correctly. Since the
memory was just kzalloc'ed, the check was always failing and SSID with
over 32 characters were allowed to go through.
This was causing a buffer overflow when copying the actual SSID to the
proper place.
This bug has been there since 2.6.29-rc4.
Cc: stable@kernel.org
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported by Ingo Molnar, we still have configuration combinations
where use of the WARN_RATELIMIT interfaces break the build because
dependencies don't get met.
Instead of going down the long road of trying to make it so that
ratelimit.h can get included by kernel.h or asm-generic/bug.h,
just move the interface into ratelimit.h and make users have
to include that.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
The below patch removes vlan_buggyright and vlan_copyright from vlan_proto_init,
so that it prints out just the fullname of vlan and the version number.
before:
[ 30.438203] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 30.441542] All bugs added by David S. Miller <davem@redhat.com>
after:
[ 31.513910] 802.1Q VLAN Support v1.8
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
CC: Joe Perches <joe@perches.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As these pointers have been printed without using %p they were missed in the
big network kptr_restrict conversion patch %p -> %pK from Dan Rosenberg.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code squashes flags to bool - this makes set_flags fail whenever
some ETH_FLAG_* equivalent features are set. Fix this.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill set but not used 'entry_offset'.
Add a default case to the switch statement so the compiler
can see that we always initialize off and size_kern before
using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit e67f88dd12 (dont hold rtnl mutex during netlink dump callbacks)
missed fact that rtnl_fill_ifinfo() must be called with rtnl held.
Because of possible deadlocks between two mutexes (cb_mutex and rtnl),
its not easy to solve this problem, so revert this part of the patch.
It also forgot one rcu_read_unlock() in FIB dump_rules()
Add one ASSERT_RTNL() in rtnl_fill_ifinfo() to remind us the rule.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit eeaeb068f1 (sch_sfq: allow big packets and be fair),
sfq_peek() can return a different skb that would be normally dequeued by
sfq_dequeue() [ if current slot->allot is negative ]
Use generic qdisc_peek_dequeued() instead of custom implementation, to
get consistent result.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Jesper Dangaard Brouer <hawk@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an ASCONF chunk is outstanding, then the following ASCONF
chunk will be queued for later transmission. But when we free
the asoc, we forget to free the ASCONF queue at the same time,
this will cause memory leak.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device passed into dev_disable_lro is a vlan, then repoint the dev
poniter so that we actually modify the underlying physical device.
Signed-of-by: Neil Horman <nhorman@tuxdriver.com>
CC: davem@davemloft.net
CC: bhutchings@solarflare.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Migrate is_vlan_dev() to if_vlan.h so that core networkig can use it
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: davem@davemloft.net
CC: bhutchings@solarflare.com
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge netfilter code uses a fake_rtable, and we must init its _metric
field or risk NULL dereference later.
Ref: https://bugzilla.kernel.org/show_bug.cgi?id=35672
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dst_default_metrics is readonly, we dont want to kfree() it later.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In igmp_group_dropped() we call ip_mc_clear_src(), which resets the number
of source filters per mulitcast. However, igmp_group_dropped() is also
called on NETDEV_DOWN, NETDEV_PRE_TYPE_CHANGE and NETDEV_UNREGISTER, which
means that the group might get added back on NETDEV_UP, NETDEV_REGISTER and
NETDEV_POST_TYPE_CHANGE respectively, leaving us with broken source
filters.
To fix that, we must clear the source filters only when there are no users
in the ip_mc_list, i.e. in ip_mc_dec_group() and on device destroy.
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
synchronize_rcu() is very slow in various situations (HZ=100,
CONFIG_NO_HZ=y, CONFIG_PREEMPT=n)
Extract from my (mostly idle) 8 core machine :
synchronize_rcu() in 99985 us
synchronize_rcu() in 79982 us
synchronize_rcu() in 87612 us
synchronize_rcu() in 79827 us
synchronize_rcu() in 109860 us
synchronize_rcu() in 98039 us
synchronize_rcu() in 89841 us
synchronize_rcu() in 79842 us
synchronize_rcu() in 80151 us
synchronize_rcu() in 119833 us
synchronize_rcu() in 99858 us
synchronize_rcu() in 73999 us
synchronize_rcu() in 79855 us
synchronize_rcu() in 79853 us
When we hold RTNL mutex, we would like to spend some cpu cycles but not
block too long other processes waiting for this mutex.
We also want to setup/dismantle network features as fast as possible at
boot/shutdown time.
This patch makes synchronize_net() call the expedited version if RTNL is
locked.
synchronize_rcu_expedited() typical delay is about 20 us on my machine.
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 20 us
synchronize_rcu_expedited() in 16 us
synchronize_rcu_expedited() in 20 us
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 18 us
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
CC: Ben Greear <greearb@candelatech.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The %pK format specifier is designed to hide exposed kernel pointers,
specifically via /proc interfaces. Exposing these pointers provides an
easy target for kernel write vulnerabilities, since they reveal the
locations of writable structures containing easily triggerable function
pointers. The behavior of %pK depends on the kptr_restrict sysctl.
If kptr_restrict is set to 0, no deviation from the standard %p behavior
occurs. If kptr_restrict is set to 1, the default, if the current user
(intended to be a reader via seq_printf(), etc.) does not have CAP_SYSLOG
(currently in the LSM tree), kernel pointers using %pK are printed as 0's.
If kptr_restrict is set to 2, kernel pointers using %pK are printed as
0's regardless of privileges. Replacing with 0's was chosen over the
default "(null)", which cannot be parsed by userland %p, which expects
"(nil)".
The supporting code for kptr_restrict and %pK are currently in the -mm
tree. This patch converts users of %p in net/ to %pK. Cases of printing
pointers to the syslog are not covered, since this would eliminate useful
information for postmortem debugging and the reading of the syslog is
already optionally protected by the dmesg_restrict sysctl.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: James Morris <jmorris@namei.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Thomas Graf <tgraf@infradead.org>
Cc: Eugene Teo <eugeneteo@kernel.org>
Cc: Kees Cook <kees.cook@canonical.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David S. Miller <davem@davemloft.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Eric Paris <eparis@parisplace.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A mis-configured filter can spam the logs with lots of stack traces.
Rate-limit the warnings and add printout of the bogus filter information.
Original-patch-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While chasing a possible net_sched bug, I found that IP fragments have
litle chance to pass a congestioned SFQ qdisc :
- Say SFQ qdisc is full because one flow is non responsive.
- ip_fragment() wants to send two fragments belonging to an idle flow.
- sfq_enqueue() queues first packet, but see queue limit reached :
- sfq_enqueue() drops one packet from 'big consumer', and returns
NET_XMIT_CN.
- ip_fragment() cancel remaining fragments.
This patch restores fairness, making sure we return NET_XMIT_CN only if
we dropped a packet from the same flow.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Jamal Hadi Salim <hadi@cyberus.ca>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
