Since the twl-core has been converted to use regmap it is no longer needed
to allocate bigger buffer for data when writing to twl.
CC: Grant Likely <grant.likely@secretlab.ca>
CC: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since a structure device is available now, use the dev_ macros instead
of the pr_ ones.
Clean some badly formatted comments.
Remove some unused variables.
Move some variable to the place they belong.
Clean some badly wrapped lines.
Align variable definition
Add missing braces in if-then-else block.
Add blank line for better readability.
Move stuff here and there...
Conflicts:
drivers/mfd/twl-core.c
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
During DT adaptation, the irq_alloc_desc was added into twl-core, but
due to the rather different and weird IRQ management required by the twl4030,
it is much better to have a different approach for it.
The issue is that twl4030 uses a two level IRQ mechanism but handles all the
PWR interrupts as part of the twl-core interrupt range. It ends up with a
range of 16 interrupts total for CORE and PWR.
The other twl4030 functionalities already have a dedicated driver and thus
their IRQs and irqdomain can and should be defined localy.
twl6030 is using a single level IRQ controller and thus does not require any
trick.
Move the irq_alloc_desc and irq_domain_add_legacy in twl4030-irq and
twl6030-irq.
Allocate together CORE and PWR IRQs for twl4030-irq.
Conflicts:
drivers/mfd/twl-core.c
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Card detect IRQ from the TWL6030 used to be provided to the MMC
controller code using a statically allocated IRQ scheme:
card_detect_irq = TWL6030_IRQ_BASE + MMCDETECT_INTR_OFFSET;
This is no longer valid in a SPARSE_IRQ context since there is no more
pre-defined TWL6030_IRQ_BASE.
Return the proper card detect IRQ value in the twl6030_mmc_card_detect_config
that will be called from the MMC controller.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl6030_irq_set_wake is not used anywhere else in the kernel
except as irq_chip.irq_set_wake. No reason for it to be exported.
Also fixes build warning:
drivers/mfd/twl6030-irq.c:230:5: warning: symbol 'twl6030_irq_set_wake' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TWL6030 family of PMIC use a shadow interrupt status register
while kernel processes the current interrupt event.
However, any write(0 or 1) to register INT_STS_A, INT_STS_B or
INT_STS_C clears all 3 interrupt status registers.
Since clear of the interrupt is done on 32k clk, depending on I2C
bus speed, we could in-adverently clear the status of a interrupt
status pending on shadow register in the current implementation.
This is due to the fact that multi-byte i2c write operation into
three seperate status register could result in multiple load
and clear of status and result in lost interrupts.
Instead, doing a single byte write to INT_STS_A register with 0x0
will clear all three interrupt status registers without the related
risk.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some drivers set PF_NOFREEZE in their kthread functions which is
completely unnecessary and racy - some part of freezer code doesn't
consider cases where PF_NOFREEZE is set asynchronous to freezer
operations.
In general, there's no reason to allow setting PF_NOFREEZE explicitly.
Remove them and change the documentation to note that setting
PF_NOFREEZE directly isn't allowed.
-v2: Dropped change to twl4030-irq.c as it no longer uses PF_NOFREEZE.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "Gustavo F. Padovan" <padovan@profusion.mobi>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: wwang <wei_wang@realsil.com.cn>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
These macros are in <linux/export.h> and will no longer be
implicitly everywhere anymore. Fix it up in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Module IRQs may still be disabled by DPM at the time the TWL6030
ISR runs, causing handle_simple_irq() to silently do nothing.
This may result in missing TWL RTC alarm wakeups, for example,
since the RTC child module ISR is not called to ack the IRQ.
Disable the TWL6030 IRQ during suspend, enable it at DPM resume
time, at which time the child module IRQs will be re-enabled.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
LOCKDEP explicitly sets all irq_desc locks as a single lock-class,
causing "possible recursive locking detected" when the TWL RTC
driver calls through enable_irq_wake to twl6030_irq_set_wake,
which recursively calls irq_set_irq_wake. Although the
irq_desc and lock are different, LOCKDEP treats these as
equivalent, presumably due to problems that can be incurred
when locking more than one irq_desc, so best to avoid this.
Suspend/resume actions implemented as PM notifiers to avoid
touch the TWL core for this.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TWL6030 devices have an interrupt line which is connected to
application processor like OMAP. These devices support multiple features
such as MMC card detect, USB cable detect, RTC interrupt, etc. that must
wake up the application processor.
With this change, TWL6030 client drivers can make use of
irq_wake() if the wakeup is desirable on it's irq events.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
I was trying to fix the error handling part because in the case of
request_irq failure, it should call kthread_stop instead of free_irq.
But it seems more reasonable to do request_irq before calling kthread_run.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The charger fault IRQs from the twl will in future patches be handled
by a seperate IRQ handler in the charger driver than the general charger
IRQ. Give them different IRQ numbers now to allow the charger driver to
be merged in the future.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
irq_desc checking in the interrupt demux routine is totally
pointless. The driver sets those lines up, so that cant go away
magically.
Remove the open coded handler magic and use the proper accessor.
This driver needs to be converted to threaded interrupts and buslock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With TWL6030-usb, VBUS SESS_VLD and SESS_END events are not generated
as expected. When these interrupts are enabled, charger VBUS detection
interrupt does not get generated. So USBOTG has to be dependent on charger
VBUS interrupts.
So added one bit for USBOTG and changed the handler to call the
USBOTG handler whenever there is a charger VBUS interrpt.
VBUS SESS_VLD and SESS_END event generation issue is under debug with
HW team. This fix might not be required once after fixing the issue.
Signed-off-by: Balaji TK <balajitk@ti.com>
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixes following sparse warnings for twl4030 and twl6030 irq files.
drivers/mfd/twl4030-irq.c:783:5: warning: symbol 'twl4030_init_irq' was not
declared. Should it be static?
drivers/mfd/twl4030-irq.c:863:5: warning: symbol 'twl4030_exit_irq' was not
declared. Should it be static?
drivers/mfd/twl4030-irq.c:873:5: warning: symbol 'twl4030_init_chip_irq' was
not declared. Should it be static?
drivers/mfd/twl6030-irq.c:226:5: warning: symbol 'twl6030_init_irq' was not
declared. Should it be static?
drivers/mfd/twl6030-irq.c:290:5: warning: symbol 'twl6030_exit_irq' was not
declared. Should it be static?
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adding card detect callback function and card detect configuration
function for MMC1 Controller on OMAP4.
Card detect configuration function does initial configuration of the
MMC Control & PullUp-PullDown registers of Phoenix.
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030.
Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
the suspend/resume initialization which was done in omap_hsmmc_gpio_init
previously is moved to the probe thus making it generic for both OMAP3 &
OMAP4.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds support for phoenix interrupt framework. New iInterrupt
status register A, B, C are introduced in Phoenix and are cleared on write.
Due to the differences in interrupt handling with respect to TWL4030,
twl6030-irq.c is created for TWL6030 PMIC
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
