This adds tlv bytes topology control creation and control load to
initialize kcontrol data. And this also adds the callbacks for
the these tlv byte kcontrols
Signed-off-by: Mythri P K <mythri.p.k@intel.com>
Signed-off-by: Divya Prakash <divya1.prakash@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support to configure module parameter during module
initialization or after module init using set module param
required by the DSP firmware sequence.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some DSP modules has user configurable parameters, which are
required by some modules at module initialization.
To configure the module algorithm parameter during initialization
we add helpers here
Signed-off-by: Divya Prakash <divya1.prakash@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some DSP modules have user configurable parameters. These
parameters are required by modules in the following scenario
- during initialization
- after initialization using set parameter
This patch adds helper routine to set module parameters using
large config set IPC message and removes params to be passed as
init module routine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Skylake we can support upton 4DMICs on the PDM port, so update
the PCM capabilities accordingly
Also add a new DAI for DMIC pin which can be used for getting raw
DMIC data
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As hdac->num_nodes is unsigned we can not check if
snd_hdac_get_sub_nodes() has returned error or success. Lets have a
temporary int to check the error value.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MCPS is freed first thing in pmd events but non memory. So if
we face error during teardown we leak this mem, so move the code
up
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds polling of CLDMA stream run bit when set
to confirm the HW reports the same value.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds pcm capability to support 16/8k rates and 32 bit formats
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module hw param fixup will change the valid bit depth based
on the fixup flag. If valid bit depth changes, need to set
the bit depth according to valid bit depth. This patch
fixes this issue of updating bit depth correctly.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PCM prepare callbacks can be called multiple times. During S3
the stream registers will be reset when Controller is reset.
When stream is resumed, these stream registers needs to reconfigured.
This patch removes the check in prepare callback() if stream already
prepared, which will allow reconfiguring of stream registers and also
decouple stream when stream is resumed to route audio via DSP.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The previous commit ef3e199a49 ("ASoC: Intel: sst: only use
sst-firmware when DW DMAC is available") does not fix the 0day
building errors thoroughly:
sound/built-in.o: In function 'dw_dma_remove'
sound/built-in.o: In function 'dw_dma_probe'
Here we fallback to select sst-firmware only when DW DMAC
is built-in selected. We may need to refactor sst common
driver and split DW related codes to platform driver, but
ATM, this fallback may be the smallest fix.
Please be noticed that after applying this patch, we may
need select DW DMAC manually in DMA driver menu, before
we can prompt and select HSW/BDW and old BYT machines.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
kzalloc() can return NULL if it fails, and then we will be dereferencing
a NULL pointer.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since driver use infoframe symbols from video/hdmi.c we should select this
symbol for this driver
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake driver uses snd_dma_buffer for data and buffer, these are variables
and not pointer so do not test field addresses.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the component framework to keep the display on till the
playback in progress.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch uses hdmi framework in video to fill audio infoframe.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ops are used for triggering HDMI streams and configuring
the parameters
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Power up/down the AFG node during runtime resume/suspend.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds HDA based HDMI driver to be used in platforms like SKL
and onwards
Register the hdmi driver with hda bus and register dais.
Also parse the widget and initialize identified pin and converter
widgets.
For simplification, currently only one pin and one converter
widget are enabled on board, as well as limit the rates supported
to simples ones and not based on ELD. This things will come
eventually once basic support for this is merged
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"data" is always NULL in this function. I think we should be passing
"&data" to sst_prepare_and_post_msg() instead of "data".
Fixes: 3d9ff34622 ('ASoC: Intel: sst: add stream operations')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Dinesh Mirche <dinesh.mirche@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound card rtd was an array and was updated to a list so update
the driver to use a list
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PM ops are required so that DAPM will suspend and resume the DSP
pipelines properly
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In ref configuration for Skylake, we support only 16bit, 48KHz,
stereo audio, so specify these as constrains for the devices
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the below warning form smatch and makes the
skl_tplg_bind_sinks take the next sink as argument which is true
when the current sink is valid
sound/soc/intel/skylake/skl-topology.c:453 skl_tplg_bind_sinks()
error: we previously assumed 'sink' could be null (see line 452)
sound/soc/intel/skylake/skl-topology.c
451
452 if (!sink)
^^^^
New check. Reversed?
453 return skl_tplg_bind_sinks(sink, skl, src_mconfig);
^^^^ This is
dereferenced inside the function.
454
455 return 0;
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When downloading the firmware/module, if the ring buffer boundary
is reached, we need to wrap to the zeroth position. On next copy
we need to copy till end of buffer and the remaining buffer needs
to be copied from zeroth position.
In this case copy was not handled correctly when wrap condition
is reached which caused invalid data to be copied resulting in
invalid hash failure.
This patch fixes the issue by handling copy at the boundary
condition correctly.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes firmware D3 IPC fails causing firmware to be in invalid
state. To recover we need to reset the DSP and then shut it down,
so don't return on error and continue resetting to recover.
On D0, firmware will be redownloaded and DSP will be back in
clean state
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During firmware download, dma buffers are allocated in prepare
and never freed on clean up. This patch frees the allocated dma
buffer in cldma controller clean up.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we call _skl_resume which also initializes the chip we no
need to call these explicitly, so remove the duplication
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For HDA codecs WAKEENABLE bit is to programmed if codec event
change has to wake the system when suspended.
In skylake I2S systems which are currently supported we have
only HDMI codec, which doesn't use this capability to detect a
HDMI connect/ disconnect event. HDMI HDA codec uses display
interface to detect connect/disconnect event.
This patch removes the WAKEBIT enabling during device D0/D3 as
this seems to cause spurious wakes on the system
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC core already does pm_runtime_get/put in the core before
opening/closing the devices.
So we do not need to do this is driver, hence remove
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds skl_nau8825_ssn4567_i2s machine driver into
machine table
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds new BE cpu dai to support SSP1 port.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the number of DAI links is statically defined by the machine
driver at build time using an array. This makes it difficult to shrink/
grow the number of DAI links at runtime in order to reflect any changes
in topology.
We can change the DAI link array in the core to a list so that PCMs and
FE DAI links can be added and deleted at runtime to reflect changes in
use case and DSP topology. The machine driver can still register DAI links
as an array.
As the 1st step, this patch change the PCM runtime array to a list. A new
PCM runtime is added to the list when a DAI link is bound successfully.
Later patches will further implement the DAI link list.
More:
- define snd_soc_new/free_pcm_runtime() to create/free a runtime.
- define soc_add_pcm_runtime() to add a runtime to the rtd list.
- define soc_remove_pcm_runtimes() to clean up the runtime list.
- traverse the rtd list to probe the link components and dais.
- Add a field "num" to PCM runtime struct, used to specify the device
number when creating the pcm device, and for a soc card to access
its dai_props array.
- The following 3rd party machine/platform drivers iterate the rtd list
to check the runtimes:
sound/soc/intel/atom/sst-mfld-platform-pcm.c
sound/soc/intel/boards/cht_bsw_rt5645.c
sound/soc/intel/boards/cht_bsw_rt5672.c
sound/soc/intel/boards/cht_bsw_max98090_ti.c
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vendor drivers no longer access a DAI link's runtime by the link index
but by matching the link name via snd_soc_get_pcm_runtime(). We assume
each DAI link has a unique name.
This is preparation for changing runtimes from an array to a list later.
Vendor drivers changed:
sound/soc/fsl/fsl-asoc-card.c
sound/soc/fsl/imx-wm8962.c
sound/soc/pxa/mioa701_wm9713.c
sound/soc/samsung/bells.c
sound/soc/samsung/littlemill.c
sound/soc/samsung/odroidx2_max98090.c
sound/soc/samsung/snow.c
sound/soc/samsung/speyside.c
sound/soc/samsung/tobermory.c
sound/soc/tegra/tegra_wm8903
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The i2c is dependency for the i2c codec drivers, so machine should depend on
i2c. WIthout this we get build failures if I2C is not selected
sound/soc/codecs/rl6347a.c: In function 'rl6347a_hw_write':
>> sound/soc/codecs/rl6347a.c:66:8: error: implicit declaration of function
>> 'i2c_master_send' [-Werror=implicit-function-declaration]
ret = i2c_master_send(client, data, 4);
^
sound/soc/codecs/rl6347a.c: In function 'rl6347a_hw_read':
>> sound/soc/codecs/rl6347a.c:114:8: error: implicit declaration of function
>> 'i2c_transfer' [-Werror=implicit-function-declaration]
ret = i2c_transfer(client->adapter, xfer, 2);
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The sst_block_ops structure is never modified, and is thus declared as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The firmware name is hard coded which doesnt allow to load
different platforms for various platforms so get this name from
available machine table and pass it to dsp context for loading
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to pass the fw name to IPC driver for loading fw, we
need to add a memeber to store the fw name
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we have common match code in place, update the SKL
driver to use the common match routines for driver entry creation
for UEFI BIOS systems
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Omair M Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves the atom driver to use the common acpi match
functions. Since atom driver has few more information in machine
table, these are appended to table and set to NULL for common
driver
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This code to find the machine is common for all drivers so move
it to a separate file and header for use in other drivers
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MCPS free was being done from PGA context which will free up MCPS
for only last modules in a pipe and not the rest causing MCPS
leak and eventual audio loss due to no "free" MCPS.
This needs to be freed for every module while cleaning up the
modules, so move the check to
skl_tplg_mixer_dapm_post_pmd_event()
Signed-off-by: Mohan Krishna Velaga <mohan.krishnax.velaga@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Smatch warns that we dereferenced substream before check, so fix
this by initializing ebus after the check
sound/soc/intel/skylake/skl-pcm.c:802 skl_get_position()
warn: variable dereferenced before check 'substream->runtime'
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the below warning reported by Dan by invoking
skl_sst_dsp_cleanup() in cleanup path on error and not bailing out
sound/soc/intel/skylake/skl-sst.c:270 skl_sst_dsp_init()
info: ignoring unreachable code.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The size of the pointer to a data structure to send is erroneously
passed to sst_ipc_tx_message_wait() as its tx_bytes argument. It should
be given the size of the pointed skl_ipc_dxstate_info structure instead.
Coincidentally, both the pointer and the structure have the same size of
8 bytes on a 64 bit machine, which "masks" the issue. Compiling for 32
bit reveals the issue more clearly.
Fix the typo for correctness, and to make the code robust to future
evolutions of the skl_ipc_dxstate_info structure size.
This fixes the following coccicheck error:
sound/soc/intel/skylake/skl-sst-ipc.c:641:8-14: ERROR: application of sizeof to pointer
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Cc: Jeeja KP <jeeja.kp@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: trivial@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
SSP0 FMT uses 24 bits so fix to the value to 24 bits
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
