These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.
Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.
Update all places in the tree using these flags with the
following semantic patch:
@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR
Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ATM, the first call of ieee80211_do_open will configure the hw as
non-idle, even if the interface being brought up is not a monitor, and
this leads to inconsistent sequences like:
register_hw()
do_open(sta)
hw_config(non-idle)
(.. sta is non-idle ..)
scan(sta)
hw_config(idle) (after scan finishes)
do_stop(sta)
do_open(sta)
(.. sta is idle ..)
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 3e8b1eb "mac80211/minstrel_ht: improve rate selection stability"
introduced a local capped prob in minstrel_ht_calc_tp but omitted to use
it to compute the per rate throughput.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 392b9ff ("mac80211: change beacon/connection polling")
removed the IEEE80211_STA_BEACON_POLL flag.
However, it accidentally removed the setting of
IEEE80211_STA_CONNECTION_POLL, making the connection polling
completely useless (the flag is always clear, so the result
is never being checked). Fix it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh STA receiving the mesh CSA action frame is not able to trigger
the mesh channel switch due to the incorrect handling and comparison
of mesh channel switch parameters element (MCSP)'s TTL. Make sure
the MCSP's TTL is updated accordingly before calling the
ieee80211_mesh_process_chnswitch. Also, we update the beacon before
forwarding the CSA action frame, so MCSP's precedence value and
initiator flag need to be updated prior to this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Multicast frames can't be transmitted as part of an aggregation
session (such a session couldn't even be set up) so don't try to
reorder them. Trying to do so would cause the reorder to stop
working correctly since multicast QoS frames (as transmitted by
the Aruba APs this was found with) would cause sequence number
confusion in the buffer.
Cc: stable@vger.kernel.org
Reported-by: Blaise Gassend <blaise@suitabletech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When initializing rates selections starting indexes upon stats update,
the minstrel_sta->max_* rates should be 'group * MCS_GROUP_RATES + i'
not 'i'. This affects settings where one of the peers does not support
any of the rates of the group 0 (i.e. when ht_cap.mcs.rx_mask[0] == 0).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh beacon was not being rebuild after user triggered a mesh
powersave change.
To solve this issue use ieee80211_mbss_info_change_notify instead
of ieee80211_bss_info_change_notify. This helper function forces
mesh beacon to be rebuild and then notifies the driver about the
beacon change.
Signed-off-by: Javier Lopez <jlopex@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit "mac80211: implement SMPS for AP" applies to AP_VLAN as well.
It assumes that sta->sdata->vif.bss_conf.bssid is present, which did not
get set for AP_VLAN.
Initialize it to sdata->vif.addr like for other interface types.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When changing cfg80211 to use RTNL locking, this caused a
deadlock in mac80211 as it calls cfg80211_sched_scan_stopped()
from a work item that's on a workqueue that is flushed with
the RTNL held.
Fix this by simply using schedule_work(), the work only needs
to finish running before the wiphy is unregistered, no other
synchronisation (e.g. with suspend) is really required since
for suspend userspace is already blocked anyway when we flush
the workqueue so will only pick up the event after resume.
Cc: stable@vger.kernel.org
Fixes: 5fe231e873 ("cfg80211: vastly simplify locking")
Reported-and-tested-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Setup chandef for radar event correctly, before we
will clear this in ieee80211_dfs_cac_cancel() function.
Without this patch mac80211 will report wrong channel
width in case we will get radar event during active CAC.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit ee1f668136.
The aformentioned commit added a check to allow
'iw wlan0 set power_save off' to work for mesh interfaces.
However, this is problematic because it also allows
'iw wlan0 set power_save on', which will crash in short order
because all of the subsequent code manipulates sdata->u.mgd.
The power-saving states for mesh interfaces can be manipulated
through the mesh config, e.g:
'iw wlan0 set mesh_param mesh_power_save=active' (which,
despite the name, actualy disables power saving since the
setting refers to the type of sleep the interface undergoes).
Cc: stable@vger.kernel.org
Fixes: ee1f668136 ("mac80211: allow disable power save in mesh")
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CSA completion could call in a driver
bss_info_changed() with a garbled `changed` flag
leading to all sorts of problems.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Trigger the mesh channel switching procedure if the mesh STA
happens to miss the CSA action frame but able to receive the
beacon containing the CSA and MCSP elements from its peer
mesh STAs.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
[fix locking in ieee80211_mesh_process_chnswitch()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the required procedures for mesh channel switching as defined
in the IEEE Std 802.11-2012 section 10.9.8.4.3 and also handle the CSA
and MCSP elements as followed:
* Add the function for updating the beacon and probe response frames
with CSA and MCSP elements during the period of switching to the new
channel. Both CSA and MCSP elements must be included in beacon and
probe response frames until the intended channel switch time.
* The ifmsh->csa_settings is set to NULL and the CSA and MCSP elements
will then be removed from the beacon or probe response frames once the
new channel is switched to.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the triggering of CSA frame using mesh interface. The
rules are more or less same with IBSS, such as not allowed to
change between the band and channel width has to be same from
the previous mode. Also, move the ieee80211_send_action_csa
to a common space so that it can be re-used by mesh interface.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Process the CSA frame according to the procedures define in IEEE Std
802.11-2012 section 10.9.8.4.3 as follow:
* The mesh channel switch parameters element (MCSP) must be availabe.
* If the MCSP's TTL is 1, drop the frame but still process the CSA.
* If the MCSP's precedence value is less than or equal to the current
precedence value, drop the frame and do not process the CSA.
* The CSA frame is forwarded after TTL is decremented by 1 and the
initiator field is set to 0. Transmit restrict field and others
are maintained as is.
* No beacon or probe response frame are handled here.
Also, introduce the debug message used for mesh CSA purpose.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the channel switch IE parsing to reduce the number
of function parameters.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used by a driver to prepare skbs for transmission, which were
obtained via functions such as ieee80211_probereq_get or
ieee80211_nullfunc_get.
This is useful for drivers that want to send those frames directly, but
need rate control information to be prepared first.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes errors in the mesh powersave logic which
cause that remote peers do not get peer power mode change
notifications and mesh peer service periods (MPSPs) got
stuck.
When closing a peer link, set the (now invalid) peer-specific
power mode to 'unknown'.
Avoid overhead when local power mode is unchanged.
Reliably clear MPSP flags on peering status update.
Avoid MPSP flags getting stuck by not requesting a further
MPSP ownership if we already are an MPSP owner.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
6c17b77b67 ensures that a device's
mac80211 queues will remain stopped while offchannel. Since the
vif can no longer be offchannel when the queues wake it's not
necessary to check for this before waking its netdev queues.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow changing to DFS channels if the channel is available for
beaconing and userspace controls DFS operation.
Channel switch announcement from other stations on DFS channels will
be interpreted as radar event. These channels will then be marked as
unvailable.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver requests to move to STATIC or DYNAMIC SMPS,
we send an action frame to each associated station and
reconfigure the channel context / driver.
Of course, non-MIMO stations are ignored.
The beacon isn't updated. The association response will
include the original capabilities. Stations that associate
while in non-OFF SMPS mode will get an action frame right
after association to inform them about our current state.
Note that we wait until the end of the EAPOL. Sending an
action frame before the EAPOL is finished can be an issue
for a few clients. Clients aren't likely to send EAPOL
frames in MIMO anyway.
When the SMPS configuration gets more permissive (e.g.
STATIC -> OFF), we don't wake up stations that are asleep
We remember that they don't know about the change and send
the action frame when they wake up.
When the SMPS configuration gets more restrictive (e.g.
OFF -> STATIC), we set the TIM bit for every sleeping STA.
uAPSD stations might send MIMO until they poll the action
frame, but this is for a short period of time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix vht streams loop, initialisation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some APs (notably a Sitecom WL-153 v1 with firmware 1.45) are sending
invalid WMM parameters setting AIFSN, ECWmin and ECWmax to zero. The
spec mandates that the value of AIFSN is at least 2, and some cards
(e.g. Intel with the iwldvm driver) can't transmit when the invalid
QoS parameters are actually uploaded to the firmware.
Since there's little chance of being able to guess the values that
the AP actually meant, disable WMM if such an invalid case is found.
Since ECWmin/ECWmax are allowed to be zero, only verify AIFSN >= 2
and ECWmin <= ECWmax.
Reviewed-by: Eliad Peller <eliad@wizery.com>
Reported-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bitrate mask were not respected in transmissions, causing (for
example) P2P GO/client to use CCK rates for auth and assoc frames.
Fix it by considering the rate mask in __rate_control_send_low().
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Transmissions with the IEEE80211_TX_CTL_NO_CCK_RATE flag set
(which can come from userspace) were no longer guaranteed to
be transmitted with allowed rates since commit 2103dec147
("mac80211: select and adjust bitrates according to channel
mode") due to a missing rate_flags check in that commit. The
commit also introduced the need to check the 5/10 MHz flags
but accidentally didn't. Fix it by adding the missing check.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a frame's timestamp is calculated, and the bitrate
calculation goes wrong and returns zero, the system
will attempt to divide by zero and crash. Catch this
case and print the rate information that the driver
reported when this happens.
Cc: stable@vger.kernel.org
Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the generic CCM aead chaining mode driver rather than a local
implementation that sits right on top of the core AES cipher.
This allows the use of accelerated implementations of either
CCM as a whole or the CTR mode which it encapsulates.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
__ieee80211_scan_completed is called from a worker. This
means that the following flow is possible.
* driver calls ieee80211_scan_completed
* mac80211 cancels the scan (that is already complete)
* __ieee80211_scan_completed runs
When scan_work will finally run, it will see that the scan
hasn't been aborted and might even trigger another scan on
another band. This leads to a situation where cfg80211's
scan is not done and no further scan can be issued.
Fix this by setting a new flag when a HW scan is being
cancelled so that no other scan will be triggered.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
include/linux/netdevice.h
net/core/sock.c
Trivial merge issues.
Removal of "extern" for functions declaration in netdevice.h
at the same time "const" was added to an argument.
Two parallel line additions in net/core/sock.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit the current implementation to a single channel context used by
a single vif, thereby avoiding multi-vif/channel complexities.
Reuse the main function from AP CSA code, but move a portion out in
order to fit the STA scenario.
Add a new mac80211 HW flag so we don't break devices that don't support
channel switch with channel-contexts. The new behavior will be opt-in.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the default setting for WMM parameters outside the for loop
to avoid redundant assignment multiple times.
Signed-off-by: Fred Zhou <fred.zy@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices may not be able to report A-MSDUs in
single buffers. Drivers for such devices were
forced to re-assemble A-MSDUs which would then
be eventually disassembled by mac80211. This could
lead to CPU cache thrashing and poor performance.
Since A-MSDU has a single sequence number all
subframes share it. This was in conflict with
retransmission/duplication recovery
(IEEE802.11-2012: 9.3.2.10).
Patch introduces a new flag that is meant to be
set for all individually reported A-MSDU subframes
except the last one. This ensures the
last_seq_ctrl is updated after the last subframe
is processed. If an A-MSDU is actually a duplicate
transmission all reported subframes will be
properly discarded.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[johannes: add braces that were missing even before]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The authentication frame has a fixied size of 30 bytes
(including header, algo num, trans seq num, and status)
followed by a variable challenge text.
Allocate using exact size, instead of over-allocation
by sizeof(ieee80211_mgmt).
Signed-off-by: Fred Zhou <fred.zy@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be useful for drivers if they have any failure cases
when joining an IBSS. Also move setting the queue parameters
to before this new call, in case the new driver op needs them
already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT_CAP_BEAMFORMER_ANTENNAS cap is actually defined in the draft as
VHT_CAP_BEAMFORMEE_STS_MAX, and its size is 3 bits long.
VHT_CAP_SOUNDING_DIMENSIONS is also 3 bits long.
Fix the definitions and change the cap masking accordingly.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some debugfs related functions snprintf was used
while scnprintf should have been used instead.
(blindly adding the return value of snprintf and supplying
it to the next snprintf might result in buffer overflow when
the input is too big)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 scan processing could get stuck if roc work for pending, but
not started when a scan request was deferred due to such roc item.
Normally the deferred scan would be started from
ieee80211_start_next_roc(), but ieee80211_sw_roc_work() calls that only
if the finished ROC was started. Fix this by calling
ieee80211_run_deferred_scan() in the case the last ROC was not actually
started.
This issue was hit relatively easily in P2P find operations where Listen
state (remain-on-channel) and Search state (scan) are repeated in a
loop.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When clients are idle for too long, hostapd sends nullfunc frames for
probing. When those are acked by the client, the idle time needs to be
updated.
To make this work (and to avoid unnecessary probing), update sta->last_rx
whenever an ACK was received for a tx packet. Only do this if the flag
IEEE80211_HW_REPORTS_TX_ACK_STATUS is set.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows calls for clients in AP_VLANs (e.g. for 4-addr) to succeed
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch "mac80211: select and adjust bitrates according to
channel mode" causes regression and breaks the extended supported rate
IE setting. Since "i" is starting with 8, so this is not necessary
to introduce "skip" here.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Reviewed-by: Jason Abele <jason@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If an Ad-Hoc node receives packets with the Cell ID or its own MAC
address as source address, it hits a WARN_ON in sta_info_insert_check()
With many packets, this can massively spam the logs. One way that this
can easily happen is through having Cisco APs in the area with rouge AP
detection and countermeasures enabled.
Such Cisco APs will regularly send fake beacons, disassoc and deauth
packets that trigger these warnings.
To fix this issue, drop such spoofed packets early in the rx path.
Cc: stable@vger.kernel.org
Reported-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IBSS members may not immediately be able to send out their beacon when
performing CSA, therefore also send a CSA action frame.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function adds the channel switch announcement implementation for the
IBSS code. It is triggered by userspace (mac80211/cfg) or by external
channel switch announcement, which have to be adopted. Both CSAs in
beacons and action frames are supported. As for AP mode, the channel
switch is applied after some time. However in IBSS mode, the channel
switch IEs are generated in the kernel.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IBSS CSA will require to disconnect if a channel switch fails, but
mac80211 should search and re-connect after this disconnect. To allow
such usage, split off the ibss disconnect process in a separate function
which only performs the disconnect without overwriting nl80211-supplied
parameters.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel switch parsing function can be re-used for the IBSS code,
put the common part into an extra function.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[also move/rename chandef_downgrade]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not override max_tp_rate, max_tp_rate2 and max_prob_rate configured
according to fixed_rate in minstrel_ht_update_stats throughput computation
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the capability to use a fixed modulation rate to minstrel rate controller
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since when we detect beacon lost we do active AP probing (using nullfunc
frame or probe request) there is no need to have beacon polling. Flags
IEEE80211_STA_BEACON_POLL seems to be used just for historical reasons.
Change also make that after we start connection poll due to beacon loss,
next received beacon will abort the poll.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No need for ERR_PTR(PTR_ERR()) since there's ERR_CAST, use it.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If it is needed to disconnect multiple virtual interfaces after
(WoWLAN-) suspend, the most obvious approach would be to iterate
all interfaces by calling ieee80211_iterate_active_interfaces()
and then call ieee80211_resume_disconnect() for each one. This
is what the iwlmvm driver does.
Unfortunately, this causes a locking dependency from mac80211's
iflist_mtx to the key_mtx. This is problematic as the former is
intentionally never held while calling any driver operation to
allow drivers to iterate with their own locks held. The key_mtx
is held while installing a key into the driver though, so this
new lock dependency means drivers implementing the logic above
can no longer hold their own lock while iterating.
To fix this, add a new ieee80211_iterate_active_interfaces_rtnl()
function that iterates while the RTNL is already held. This is
true during suspend/resume, so that then the locking dependency
isn't introduced.
While at it, also refactor the various interface iterators and
keep only a single implementation called by the various cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni reported that with mac80211_hwsim, multicast TX was causing
crashes due to invalid vif->cab_queue assignment. It turns out that
this is caused by change_interface() getting invoked and not having
the vif->type/vif->p2p assigned correctly before calling the queue
check (ieee80211_check_queues). Fix this by passing the 'external'
interface type to the function and adjusting it accordingly.
While at it, also fix the error path in change_interface, it wasn't
correctly resetting to the external type but using the internal one
instead.
Fortunately this affects on hwsim because all other drivers set the
vif->type/vif->p2p variables when changing iftype. This shouldn't
be needed, but almost all implementations actually do it for their
own internal handling.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Seth reports that some APs, notably the Netgear WNDAP360, send
invalid ECSA IEs in probe response frames with the operating
class and channel number both set to zero, even when no channel
switch is being done. As a result, any scan while connected to
such an AP results in the connection being dropped.
Fix this by ignoring any channel switch announcment in probe
response frames entirely, since we're connected to the AP we
will be receiving a beacon (and maybe even an action frame) if
a channel switch is done, which is sufficient.
Cc: stable@vger.kernel.org # 3.10
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add flags intended to report various auxiliary information
and introduce the NL80211_RXMGMT_FLAG_ANSWERED flag to report
that the frame was already answered by the device.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[REPLIED->ANSWERED, reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to 802.11-2012 9.3.2.10, paragraph 4, QoS
data frames with a group address in the Address 1 field
have sequence numbers allocated from the same counter
as non-QoS data and management frames. Without this
flag, some drivers may not assign sequence numbers, and
in rare cases frames might get dropped. Set the control
flag accordingly.
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the mesh STA responds to probe request from legacy STA
but now it will only respond to legacy STA if the legacy STA does include
the specific mesh ID or wildcard mesh ID in the probe request.
The iw patch "iw: scan using meshid" can be used either by legacy STA
or by mesh STA to do active scanning by inserting the mesh ID in the
probe request frame.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Acked-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 currently sets WIPHY_FLAG_SUPPORTS_SCHED_SCAN based on whether
the start_sched_scan operation is supported or not, but that will not
be correct for all drivers, we're adding scheduled scan to the iwlmvm
driver but it depends on firmware support.
Therefore, move setting WIPHY_FLAG_SUPPORTS_SCHED_SCAN into the drivers
so that they can control it regardless of implementing the operation.
This currently only affects the TI drivers since they're the only ones
implementing scheduled scan (in a mac80211 driver.)
Acked-by: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sujith reports that my commit af61a16518
("mac80211: add control port protocol TX control flag") broke ath9k
(aggregation). The reason is that I made minstrel_ht use the flag in
the TX status path, where it can have been overwritten by the driver.
Since we have no more space in info->flags, revert that part of the
change for now, until we can reshuffle the flags or so.
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
my earlier patch "mac80211: change IBSS channel state to chandef"
created a regression by ignoring the channel parameter in
__ieee80211_sta_join_ibss, which breaks IBSS channel selection. This
patch fixes this situation by using the right channel and adopting the
selected bandwidth mode.
Cc: stable@vger.kernel.org
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
brcm80211 cannot handle sending frames with CCK rates as part of an
A-MPDU session. Other drivers may have issues too. Set the flag in all
drivers that have been tested with CCK rates.
This fixes a reported brcmsmac regression introduced in
commit ef47a5e4f1aaf1d0e2e6875e34b2c9595897bef6
"mac80211/minstrel_ht: fix cck rate sampling"
Cc: stable@vger.kernel.org # 3.10
Reported-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IBSS needs to release the channel context when leaving
but I evidently missed that. Fix it.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to be able to (securely) keep connections alive after
the system was suspended for WoWLAN, we need some additional
APIs. We already have API (ieee80211_gtk_rekey_notify) to tell
wpa_supplicant about the new replay counter if GTK rekeying
was done by the device while the host was asleep, but that's
not sufficient.
If GTK rekeying wasn't done, we need to tell the host about
sequence counters for the GTK (and PTK regardless of rekeying)
that was used while asleep, add ieee80211_set_key_rx_seq() for
that.
If GTK rekeying was done, then we need to be able to disable
the old keys (with ieee80211_remove_key()) and allocate the
new GTK key(s) in mac80211 (with ieee80211_gtk_rekey_add()).
If protocol offload (e.g. ARP) is implemented, then also the
TX sequence counter for the PTK must be updated, using the new
ieee80211_set_key_tx_seq() function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel Switch will later require to generate beacons without setting
them immediately. Therefore split the presp generation in an own
function. Splitting the original very long function might be a good idea
anyway.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch decouples the power save processing from the frame decryption
by running the decrypt rx handler after sta_process. In the case where
the decryption failed for some reason, the stack used to not process
the PM and MOREDATA bits for that frame. The stack now always performs
power save processing regardless of the decryption result. That means that
encrypted data frames and NULLFUNC frames are now handled in the same way
regarding power save processing, making the stack more robust.
Signed-off-by: Johan Almbladh <ja@anyfi.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases mac80211 will scan before creating an IBSS
even if bssid and frequency have been forced by the user.
This is not needed and leads only to a delay in the IBSS
establishment phase.
Immediately create the cell if both bssid and frequency
(and fixed_freq is set) have been specified.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the wdev from cfg80211 on to the driver as the vif
if given and it's valid for the driver.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To allow drivers to implement per-interface testmode operations
more easily, pass a wdev pointer if any identification for one
was given from userspace. Clean up the code a bit while at it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A lot of drivers check the frame protocol for ETH_P_PAE,
for various reasons (like making those more reliable).
Add a new flags bitmap to the TX control info and a new
flag indicating the control port protocol is in use to
let all drivers also apply such logic to other control
port protocols, should they be configured.
Also use the new flag in the iwlwifi drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow lowest basic rate to be used for unicast management frame in
mesh. Otherwise, the lowest supported rate is used for unicast
management frame, such as 1Mbps for 2.4GHz and 6Mbps for 5GHz. Rename
the rc_send_low_broadcast to re_send_low_basicrate since now it is
also applied to unicast management frame in mesh.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few places in the code (mac80211 and iwlmvm) use the same
TU_TO_JIFFIES() macro and could use TU_TO_EXP_TIME() that
mac80211 has. Make these available to everyone and use them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The count field in CSA must be decremented with each beacon
transmitted. This patch implements the functionality for drivers
using ieee80211_beacon_get(). Other drivers must call back manually
after reaching count == 0.
This patch also contains the handling and finish worker for the channel
switch command, and mac80211/chanctx code to allow to change a channel
definition of an active channel context.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[small cleanups, catch identical chandef]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a per-station debugfs file indicating the TIDs (as
a bitmap) that the driver has data buffered on.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The radiotap VHT info is 12 bytes (required to be aligned on 2) :
u16 known - IEEE80211_RADIOTAP_VHT_KNOWN_*
u8 flags - IEEE80211_RADIOTAP_VHT_FLAG_*
u8 bandwidth
u8 mcs_nss[4]
u8 coding
u8 group_id
u16 partial_aid
ATM mac80211 can handle IEEE80211_RADIOTAP_VHT_KNOWN_{GI,BANDWIDTH} and
mcs_nss[0] (i.e single user) in simple cases.
This is more a placeholder to let sniffers give more clues for VHT,
since we don't have yet the proper infrastructure/conventions
in mac80211 for complete feedback (e.g consider dynamic BW).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A station which is not authorized has to be purged earlier
to give it a chance to re-try to establish an IBSS/RSN
session soon. Set the timeout to 10 seconds.
Some refactoring has also been done to allow the IBSS
submodule to have its own expiring function.
Reported-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change mac80211 LED trigger code to use the generic
led_trigger_blink_oneshot() API for transmit and receive activity
indication.
This gives a better feedback to the user, as with the new API each
activity event results in a visible blink, while a constant traffic
results in a continuous blink at constant rate.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
[fix LED disabled build error]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case the AP has different regulatory information than we do,
it can happen that we connect to an AP based on e.g. the world
roaming regulatory data, and then update our database with the
AP's country information disables the channel the AP is using.
If this happens on an HT AP, the bandwidth tracking code will
hit the WARN_ON() and disconnect. Since that's not very useful,
ignore the channel-disable flag in bandwidth tracking.
Cc: stable@vger.kernel.org
Reported-by: Chris Wright <chrisw@sous-sol.org>
Tested-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While we're connected, the AP shouldn't change the primary channel
in the HT information. We checked this, and dropped the connection
if it did change it.
Unfortunately, this is causing problems on some APs, e.g. on the
Netgear WRT610NL: the beacons seem to always contain a bad channel
and if we made a connection using a probe response (correct data)
we drop the connection immediately and can basically not connect
properly at all.
Work around this by ignoring the HT primary channel information in
beacons if we're already connected.
Also print out more verbose messages in the other situations to
help diagnose similar bugs quicker in the future.
Cc: stable@vger.kernel.org [3.10]
Acked-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TX status notification can get lost, or the frames could
get stuck on the queue, so don't wait for the callback
from the driver forever and instead time out after half
a second.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit "3d9646d mac80211: fix channel selection bug" introduced a possible
infinite loop by moving the out target above the chandef_downgrade
while loop. When we downgrade to NL80211_CHAN_WIDTH_20_NOHT, we jump
back up to re-run the while loop...indefinitely. Replace goto with
break and carry on. This may not be sufficient to connect to the AP,
but will at least keep the cpu from livelocking. Thanks to Derek Atkins
as an extra pair of debugging eyes.
Cc: stable@kernel.org
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My commit:
commit 12e7f51702
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Thu Feb 28 10:55:26 2013 +0100
mac80211: cleanup generic suspend/resume procedures
removed check for deleting MONITOR and AP_VLAN when suspend. That can
cause a crash (i.e. in iwlagn_mac_remove_interface()) since we remove
interface in the driver that we did not add before.
Reference:
http://marc.info/?l=linux-kernel&m=137391815113860&w=2
Bisected-by: Ortwin Glück <odi@odi.ch>
Reported-and-tested-by: Ortwin Glück <odi@odi.ch>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch is intended to avoid the buffering to non-assoc mesh STA
and also to avoid the triggering of frame to non-assoc mesh STA which
could cause kernel panic in specific hw.
One of the examples, is kernel panic happens to ath9k if user space
inserts the mesh STA and not proceed with the SAE and AMPE, and later
the same mesh STA is detected again. The sta_state of the mesh STA remains
at IEEE80211_STA_NONE and if the ieee80211_sta_ps_deliver_wakeup is called
and subsequently the ath_tx_aggr_wakeup, the kernel panic due to
ath_tx_node_init is not called before to initialize the require data
structures.
This issue is reported by Cedric Voncken before.
http://www.spinics.net/lists/linux-wireless/msg106342.html
[<831ea6b4>] ath_tx_aggr_wakeup+0x44/0xcc [ath9k]
[<83084214>] ieee80211_sta_ps_deliver_wakeup+0xb8/0x208 [mac80211]
[<830b9824>] ieee80211_mps_sta_status_update+0x94/0x108 [mac80211]
[<83099398>] ieee80211_sta_ps_transition+0xc94/0x34d8 [mac80211]
[<8022399c>] nf_iterate+0x98/0x104
[<8309bb60>] ieee80211_sta_ps_transition+0x345c/0x34d8 [mac80211]
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When priv_sta == NULL, mi->prev_sample is dereferenced too early. Move
the assignment further down, after the rate_control_send_low call.
Reported-by: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a driver (like hwsim) uses HW queue control an
active monitor vif needs to be used for the queues,
make the code do that. Otherwise we'd bail out and
drop the frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set the Forwarding bit in Mesh Capability Info according
to dot11MeshForwarding as defined in IEEE 802.11-2012
section 8.4.2.100.8.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is an off-by-one error in the beacon generation for the ibss mode,
falsely a rate the extended supported rates which was already added to
supported rates, messing up the beacon. This was introduced by commit
"mac80211: select and adjust bitrates according to channel mode".
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There appear to be two regressions in ibss.c when calling
ieee80211_sta_def_wmm_params():
* the second argument should be a rate length, not a rate array. This
was introduced by my commit "mac80211: select and adjust bitrates
according to channel mode"
* the third argument is not initialized (anymore), making further
checks within this function useless.
Since ieee80211_sta_def_wmm_params() is only used by ibss anyway,
remove the function entirely and handle the operating mode decision
immediately.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was originally designed to fail when a 40+/40- mode can not be
used, but basic modes (such as 5/10/20 MHz) must be handled
with an error.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Use a chandef instead of just the channel for scanning, and enable
5/10 Mhz scanning for IBSS mode. Also reporting is changed to the new
inform_bss functions.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Some regulations (like germany, but also FCC) express their transmission
power limit in dBm/MHz or mW/MHz. To cope with that and be on the safe
side, reduce the maximum power to half (10 MHz) or quarter (5 MHz)
when operating on these reduced bandwidth channels.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Mandatory rates for 5 and 10 MHz are different from the rates used for
20 MHz in 2.4 GHz mode, as they use OFDM only.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
The various components accessing the bitrates table must use consider
the used channel bandwidth to select only available rates or calculate
the bitrate correctly.
There are some rates in reduced bandwidth modes which can't be
represented as multiples of 500kbps, like 2.25 MBit/s in 5 MHz mode. The
standard suggests to round up to the next multiple of 500kbps, just do
that in mac80211 as well.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[make rate unsigned in ieee80211_add_tx_radiotap_header(), squash fix]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Wireshark already defines radiotap channel flags for 5 and 10 MHz, so
just use them in Linux radiotap too. Furthermore, add rx status flags to
allow drivers to report when they received data on 5 or 10 MHz channels.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
according to IEEE 802.11-2012 section 18, various timings change
when using 5 MHz and 10 MHz. Reflect this by using a "shift" when
calculating durations.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
5 and 10 MHz support needs to know the current operating channel width,
add the chandef to the rate control API.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
When per-chain signal information is available, don't add
the antenna field once but instead add a radiotap namespace
for each chain containing the chain/antenna number and the
signal strength on that chain.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
The duplicate retransmission detection code in mac80211
erroneously attempts to do the check for every frame,
even frames that don't have a sequence control field or
that don't use it (QoS-Null frames.)
This is problematic because it causes the code to access
data beyond the end of the SKB and depending on the data
there will drop packets erroneously.
Correct the code to not do duplicate detection for such
frames.
I found this error while testing AP powersave, it lead
to retransmitted PS-Poll frames being dropped entirely
as the data beyond the end of the SKB was always zero.
Cc: stable@vger.kernel.org [all versions]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As reported in https://bugzilla.kernel.org/show_bug.cgi?id=60514,
the station loop never initialises 'sinfo' and therefore adds up
a stack values, leaking stack information (the number of times it
adds values is easily obtained another way.)
Fix this by initialising the sinfo for each station to add.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
The CCK group needs special treatment to set the right flags and rate
index. Add this missing check to prevent setting broken rates for tx
packets.
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
For the workqueue creation interfaces that do not expect format strings,
make sure they cannot accidently be parsed that way. Additionally, clean
up calls made with a single parameter that would be handled as a format
string. Many callers are passing potentially dynamic string content, so
use "%s" in those cases to avoid any potential accidents.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously the default mesh STA nonpeer power mode was
UNKNOWN (0) make the default mesh STA power mode ACTIVE,
to prevent unnecessary frame buffering while peering is
not yet complete. Fixes a panic in ath9k_htc when adding
stations from userspace, and mcast buffered frames are
later released.
Thanks to Bob Copeland for his help debugging this.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Useful for userspace mesh to authenticate and peer without
a station entry, since both steps may fail anyway.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing so will allow us to hold the BSS (not just ref it) over the
association process, thus ensuring that it doesn't time out and
gets invisible to the user (e.g. in 'iw wlan0 link'.)
This also fixes a leak in mac80211 where it doesn't always release
the BSS struct properly in all cases where calling this function.
This leak was reported by Ben Greear.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge mac80211 to avoid conflicts with the nl80211 attrbuf
changes.
Conflicts:
net/mac80211/iface.c
net/wireless/nl80211.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 6d810f1032
In this way an IBSS station will not use the AUTH messages
to trigger a state reinitialisation anymore.
The behaviour was racy and was not working properly.
It has been introduced to help wpa_supplicant to support
IBSS/RSN, however all the logic is now getting moved into
wpa_s itself which will also be in charge of handling the
AUTH messages thanks to the mgmt frame registration.
If userspace does not register for receiving AUTH frames
then mac80211 will still reply by itself.
At the same time, the auth frame registration counter can be
removed since it is not needed anymore.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[remove unused variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This should make some parts cleaner and is also required for handling
5/10 MHz properly.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is a collection of minor fixes:
* don't allow HT IEs in IBSS for 5/10 MHz
* don't allow HT IEs in Mesh for 5/10 MHz
* don't downgrade from/to 5 and 10 MHz channels
* don't try HT rates for 5 and 10 MHz channels when selecting rates
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of updating the mesh beacon immediately when
requested (which would require the sdata_lock()), defer it
to the mac80211 workqueue.
Fixes yet another deadlock on calling sta_info_flush()
with the sdata_lock() held from ieee80211_stop_mesh(). We
could just drop the sdata_lock() around the
mesh_sta_cleanup() call, but this path is also taken from
several non-locked error paths.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix comment position]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Track the AP's beacon rate in the scan BSS data and in the
interface configuration to let the drivers know which rate
the AP is using. This information may be used by drivers,
in our case to let the firmware optimise beacon RX.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All accesses of the tid_start_tx lock should be protected
by sta->lock if there is any chance that another thread
could still be accessing the sta object.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ben reports that kmemleak is saying TX aggregation TID
structs are leaked. Given his workload, I suspect that
they're leaked because stations are destroyed before
their aggregation sessions get a chance to start. Fix
this by simply freeing structs that are not used yet.
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The order of parameters was mixed up, introduced in commit
"mac80211: improve the rate control API"
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a CAC is running and stop_ap is called (e.g. when hostapd is killed
while performing CAC), the CAC must be aborted immediately.
Otherwise ieee80211_stop_ap() will try to stop it when it's too late -
wdev->channel is already NULL and the abort event can not be generated.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are some APs, notably 2G/3G/4G Wifi routers, specifically the
"Onda PN51T", "Vodafone PocketWiFi 2", "ZTE MF60" and a similar
T-Mobile branded device [1] that erroneously don't include all the
needed information in (re)association response frames. Work around
this by assuming the information is the same as it was in the
beacon or probe response and using the data from there instead.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58881.
[1] https://bbs.archlinux.org/viewtopic.php?pid=1277305
Note that this requires marking the first ieee802_11_parse_elems()
argument const, otherwise we'd get a compiler warning.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Michal Zajac <manwe@manwe.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 passes a NULL channel to mgmt_tx if the frame has
to be sent on the one currently in use by the device.
Make the implementation of mgmt_tx correctly handle this
case. Fail if offchan is required.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[fix RCU locking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mesh uses mandatory rates as the default basic rates. Allow basic
rates to be configured during mesh join. Basic rates are applied only if
channel is also provided with mesh join command.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[some whitespace fixes, refuse basic rates w/o channel]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time it takes to see the peer link expire may differ
by a minute since sta_expire() is run once a minute as a
mesh housekeeping task.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch "cfg80211/mac80211: use cfg80211 wdev mutex in
mac80211" introduced several deadlocks by converting the
ifmsh->mtx to wdev->mtx. Solve these by:
1. drop the cancel_work_sync() in ieee80211_stop_mesh().
Instead make the mesh work conditional on whether the mesh
is running or not.
2. lock the mesh work with sdata_lock() to protect beacon
updates and prevent races with wdev->mesh_id_len or
cfg80211.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently beacon availability upon association is marked by have_beacon
flag of assoc_data structure that becomes unavailable when association
completes. However beacon availability indication is required also after
association to inform a driver. Currently dtim_period parameter is used
for this purpose. Move have_beacon flag to another structure, persistant
throughout a interface's life cycle. Use suitable sematics for beacon
availability indication.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[fix another instance of BSS_CHANGED_DTIM_PERIOD in docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_rx_bss_info() deals with dtim_period setting and PS update
when associated. Move all these to another locations cleaning this
function. Also, the current implementation is buggy because when it
calls ieee80211_recalc_ps() bss_conf->dtim_period is notset properly
yet and thus nothing will happen.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do some cleanups in the cfg80211 SME APIs, which are
only used by mac80211.
Most of these functions get a frame passed, and there
isn't really any reason to export multiple functions
as cfg80211 can check the frame type instead, do that.
Additionally, the API functions have confusing names
like cfg80211_send_...() which was meant to indicate
that it sends an event to userspace, but gets a bit
confusing when there's both TX and RX and they're not
all clearly labeled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The connection monitor needs to know the tx status of
nullframes to work properly.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
