rdc321x-wdt currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On some motherboards the it8712f watchdog does not work unless
the game port was enabled. see Bug 13140. We therefor add a note
to Kconfig.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* fix devinit and devexit sections
* fix platform removal code so that the iounmap happens after the removal of the timer.
* changes the reboot_notifier by a platform shutdown method.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds an additional LPC Controller DeviceID for the Intel Patsburg PCH for TCO Watchdog.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The creation of the I/O clock domain requires some adjustments. Since
the watchdog counters are clocked by the I/O clock, use its rate for
timing calculations.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/1659/
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The iTCO_wdt driver erroneously releases the pci_dev, and causes PCI hotremove
to fail because of an incorrect usage count.
The probe for this driver does a for_each_pci_dev() which gets a reference for
a pci_dev when iTCO_wdt_init() is successful. The for_each_pci_dev() loop
puts a reference for a pci_dev when iTCO_wdt_init() fails, so the
iTCO_wdt_init() does not need to do any pci_dev_put()'s.
The only pci_dev_put() that is required is in the iTCO_wdt_cleanup() function.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for the Broadcom BCM63xx SoC built-in watchdog, it
uses one of the BCM63xx hardware timer id.
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On iEi PCISA-9652-R10 (BIOS version 1.5) single board computer reads
from the game port do not seem to reset the watchdog timer. This patch
adds a module parameter wdt_config_reg to specify alternative reset
sources. At least WDT_RESET_KBD has been tested, even just running
while true; do
setleds -L +scroll
sleep 1
setleds -L -scroll
sleep 1
done
is enough to keep the watchdog happy.
Signed-off-by: Timo Juhani Lindfors <timo.lindfors@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for watchdogs with 8b timers, like ones in
IT8702F and older revisions of IT8712F Super IO chip, to it87_wdt
driver. This patch should be used after the patch
'it87_wdt: Add support for IT8720F watchdog'.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This simple patch adds support for a watchdog in IT8720F Super IO chip
to it87_wdt driver.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The current iTCO_wdt driver warnings are confusing. Currently when the device
driver returns an error the console contains:
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware
iTCO_wdt: No card detected
After the patch,
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: failed to reset NO_REBOOT flag, device disabled by hardware/BIOS
Clean this up and use the word "device" to describe the device.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the Intel Patsburg (PCH) DeviceIDs for iTCO Watchdog.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
block: autoconvert trivial BKL users to private mutex
drivers: autoconvert trivial BKL users to private mutex
ipmi: autoconvert trivial BKL users to private mutex
mac: autoconvert trivial BKL users to private mutex
mtd: autoconvert trivial BKL users to private mutex
scsi: autoconvert trivial BKL users to private mutex
Fix up trivial conflicts (due to addition of private mutex right next to
deletion of a version string) in drivers/char/pcmcia/cm40[04]0_cs.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (71 commits)
powerpc/44x: Update ppc44x_defconfig
powerpc/watchdog: Make default timeout for Book-E watchdog a Kconfig option
fsl_rio: Add comments for sRIO registers.
powerpc/fsl-booke: Add e55xx (64-bit) smp defconfig
powerpc/fsl-booke: Add p5020 DS board support
powerpc/fsl-booke64: Use TLB CAMs to cover linear mapping on FSL 64-bit chips
powerpc/fsl-booke: Add support for FSL Arch v1.0 MMU in setup_page_sizes
powerpc/fsl-booke: Add support for FSL 64-bit e5500 core
powerpc/85xx: add cache-sram support
powerpc/85xx: add ngPIXIS FPGA device tree node to the P1022DS board
powerpc: Fix compile error with paca code on ppc64e
powerpc/fsl-booke: Add p3041 DS board support
oprofile/fsl emb: Don't set MSR[PMM] until after clearing the interrupt.
powerpc/fsl-booke: Add PCI device ids for P2040/P3041/P5010/P5020 QoirQ chips
powerpc/mpc8xxx_gpio: Add support for 'qoriq-gpio' controllers
powerpc/fsl_booke: Add support to boot from core other than 0
powerpc/p1022: Add probing for individual DMA channels
powerpc/fsl_soc: Search all global-utilities nodes for rstccr
powerpc: Fix invalid page flags in create TLB CAM path for PTE_64BIT
powerpc/mpc83xx: Support for MPC8308 P1M board
...
Fix up conflict with the generic irq_work changes in arch/powerpc/kernel/time.c
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
The PowerPC Book-E watchdog driver (booke_wdt.c) defines a default timeout
value in the code based on whether it's a Freescale Book-E part of not.
Instead of having hard-coded values in the driver, make it a Kconfig
option.
As newer chips gets faster, the current default values become less
appropriate, since the timeout sometimes occurs before the kernel finishes
booting. Making the value a Kconfig option allows BSPs to configure a new
value without requiring the wdt_period command-line parameter to be set.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Register the __init and __exit functions in the PowerPC Book-E Watchdog
driver as module entry/exit functions, and modify the Kconfig entry.
Add a .release method for the PowerPC Book-E Watchdog driver, so that the
watchdog is disabled when the driver is closed.
Loosely based on original code from Jiang Yutang <b14898@freescale.com>.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add missing #inclusions of <linux/irq.h> to a whole bunch of files that should
really include it. Note that this can replace #inclusions of <asm/irq.h>.
This is required for the patch to sort out irqflags handling function naming to
compile on MIPS.
The problem is that these files require access to things like setup_irq() -
which isn't available by #including <linux/interrupt.h>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
These drivers do not seem to be under active
maintainance from my brief investigation. Apologies
to those maintainers that I have missed.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Call runtime pm APIs pm_runtime_put_sync() and pm_runtime_get_sync()
for enabling/disabling the clocks, sysconfig settings instead of using
clock FW APIs.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The NXP LPC32XX processor use the same watchdog as the Philips
PNX4008 processor.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Since it may be already enabled by bootloader or some other utility. This patch
makes sure that the watchdog is disabled before any userspace daemon opens the
device. It is also required by the watchdog API.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
irq and reboot notifier are acquired in module_init() but never released.
They should be released correctly, otherwise reloading the module or error
during module_init() will cause a problem.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Andrew Sharp <andy.sharp@lsi.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
hpwdt is quite functional without the NMI decoding feature.
This change lets users disable the NMI portion at compile-time
via the new HPWDT_NMI_DECODING config option.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Move NMI-decoding initialisation and exit code to seperate functions so that
we can ifdef-out parts of it in the future.
Also, this is for a device, so let's use dev_info instead of printk.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The term "decoding" more clearly explains what hpwdt is doing. It isn't
just finding the source of the interrupt, but rather aids in decoding what
the interrupt means.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reorganize this function to remove excess indentation and highlight
the single return code. (No functional change).
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Let applications check the amount of time left before the watchdog will fire.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The hpwdt timer is a 16 bit value with 128ms resolution.
Let applications use this entire range.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Define a macro to convert from seconds to timer ticks.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The 32-bit assembly is guarded by an #ifndef CONFIG_X86_64. Kconfig prevents
us from building this driver on !X86, so that happens to suffice - but we
should really lock it down to #ifdef CONFIG_X86_32.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver supports both iLO2 and iLO3, but our user-visible strings
currently only reference iLO2. Let's just call it "iLO2+" to avoid having
to update strings for each iLO generation. This driver doesn't support
iLO ASICs prior to iLO2, but that is sufficiently explained in Kconfig.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* Group together includes specific to NMI sourcing
* Group defines only used by NMI sourcing together
* Group declarations specific to NMI sourcing together
This gives a clean seperation of watchdog specific items and
NMI sourcing specific items (which is needed for making it
possible to build hpwdt without the NMI functionality).
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reorganization only.
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* remove unnecessary includes
* We use a spinlock, but lacked the include
* We need bitops.h for test_and_set_bit/clear_bit
Signed-off-by: dann frazier <dannf@hp.com>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a new watchdog driver for the Fintek F71808E and F71882FG Super I/O
controllers.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Set the paranet of the misc_device before we register the misc_device.
Reported-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Wim Van sebroeck <wim@iguana.be>
Move the VENDOR/DEVICE ids to pci_ids.h.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When removing the watchdog platform device, we need to
disable the access to userspace first. It makes no sense
to remove the drivers clock, irq's, ... and then disable
userspace access.
the order of removal has also been changed so that it
is the reverse of probing (this way the clock is also
disabled sooner).
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
