After a resume the hypervisor/tools may change console event
channel number. We should re-query it.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
After a resume the hypervisor/tools may change xenbus event
channel number. We should re-query it.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
When a guest is resumed, the hypervisor may change event channel
assignments. If this happens and the guest uses 2-level events it
is possible for the interrupt to be claimed by wrong VCPU since
cpu_evtchn_mask bits may be stale. This can happen even though
evtchn_2l_bind_to_cpu() attempts to clear old bits: irq_info that
is passed in is not necessarily the original one (from pre-migration
times) but instead is freshly allocated during resume and so any
information about which CPU the channel was bound to is lost.
Thus we should clear the mask during resume.
We also need to make sure that bits for xenstore and console channels
are set when these two subsystems are resumed. While rebind_evtchn_irq()
(which is invoked for both of them on a resume) calls irq_set_affinity(),
the latter will in fact postpone setting affinity until handling the
interrupt. But because cpu_evtchn_mask will have bits for these two
cleared we won't be able to take the interrupt.
With that in mind, we need to bind those two channels explicitly in
rebind_evtchn_irq(). We will keep irq_set_affinity() so that we have a
pass through generic irq affinity code later, in case something needs
to be updated there as well.
(Also replace cpumask_of(0) with cpumask_of(info->cpu) in
rebind_evtchn_irq(): it should be set to zero in preceding
xen_irq_info_evtchn_setup().)
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reported-by: Annie Li <annie.li@oracle.com>
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Since Roland stepped down, the community asked me to take his place, and
the nomination was followed by sufficient votes and no dissensions that
we can move forward with the change.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Most headers for InfiniBand/RDMA are located under
include/rdma/ and include/uapi/rdma.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
See also patch "IPoIB/cm: Add connected mode support for devices
without SRQs" (commit ID 68e995a295). Detected by smatch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove these log messages in favor of per-endpoint counters as well as
device-global counters that can be inspected via debugfs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Addresses the following kernel logs seen during boot of sparc systems:
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Signed-off-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Commit 283e7ad02 ("init: stricter checking of major:minor root=
values") was so strict that it exposed the fact that a previously
unknown device format was being used.
Distributions like Ubuntu uses klibc (rather than uswsusp) to resume
system from hibernation. klibc expressed the swap partition/file in
the form of major:minor:offset. For example, 8:3:0 represents a swap
partition in klibc, and klibc's resume process in initrd will finally
echo 8:3:0 to /sys/power/resume for manually resuming. However, due
to commit 283e7ad02's stricter checking, 8:3:0 will be treated as an
invalid device format, and manual resuming from hibernation will fail.
Fix this by adding support for devices with major:minor:offset format
when resuming from hibernation.
Reported-by: Prigent, Christophe <christophe.prigent@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This reverts Linux 4.1-rc1 commit 0618764cb2.
The problem which that commit attempts to fix actually lies in the
Freescale CAAM crypto driver not dm-crypt.
dm-crypt uses CRYPTO_TFM_REQ_MAY_BACKLOG. This means the the crypto
driver should internally backlog requests which arrive when the queue is
full and process them later. Until the crypto hw's queue becomes full,
the driver returns -EINPROGRESS. When the crypto hw's queue if full,
the driver returns -EBUSY, and if CRYPTO_TFM_REQ_MAY_BACKLOG is set, is
expected to backlog the request and process it when the hardware has
queue space. At the point when the driver takes the request from the
backlog and starts processing it, it calls the completion function with
a status of -EINPROGRESS. The completion function is called (for a
second time, in the case of backlogged requests) with a status/err of 0
when a request is done.
Crypto drivers for hardware without hardware queueing use the helpers,
crypto_init_queue(), crypto_enqueue_request(), crypto_dequeue_request()
and crypto_get_backlog() helpers to implement this behaviour correctly,
while others implement this behaviour without these helpers (ccp, for
example).
dm-crypt (before the patch that needs reverting) uses this API
correctly. It queues up as many requests as the hw queues will allow
(i.e. as long as it gets back -EINPROGRESS from the request function).
Then, when it sees at least one backlogged request (gets -EBUSY), it
waits till that backlogged request is handled (completion gets called
with -EINPROGRESS), and then continues. The references to
af_alg_wait_for_completion() and af_alg_complete() in that commit's
commit message are irrelevant because those functions only handle one
request at a time, unlink dm-crypt.
The problem is that the Freescale CAAM driver, which that commit
describes as having being tested with, fails to implement the
backlogging behaviour correctly. In cam_jr_enqueue(), if the hardware
queue is full, it simply returns -EBUSY without backlogging the request.
What the observed deadlock was is not described in the commit message
but it is obviously the wait_for_completion() in crypto_convert() where
dm-crypto would wait for the completion being called with -EINPROGRESS
in the case of backlogged requests. This completion will never be
completed due to the bug in the CAAM driver.
Commit 0618764cb2 incorrectly made dm-crypt wait for every request,
even when the driver/hardware queues are not full, which means that
dm-crypt will never see -EBUSY. This means that that commit will cause
a performance regression on all crypto drivers which implement the API
correctly.
Revert it. Correct backlog handling should be implemented in the CAAM
driver instead.
Cc'ing stable purely because commit 0618764cb2 did. If for some reason
a stable@ kernel did pick up commit 0618764cb2 it should get reverted.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Reviewed-by: Horia Geanta <horia.geanta@freescale.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pull crypto fixes from Herbert Xu:
"This fixes a build problem with bcm63xx and yet another fix to the
memzero_explicit function to ensure that the memset is not elided"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: bcm63xx - Fix driver compilation
lib: make memzero_explicit more robust against dead store elimination
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gmuD
-----END PGP SIGNATURE-----
Merge tag 'media/v4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Three driver fixes:
- fix for omap4, fixing a regression due to a subsystem API that got
removed for 4.1 (commit efde234674);
- fix for one of the formats supported by Marvel ccic driver;
- fix rcar_vin driver that, when stopping abnormally, the driver
can't return from wait_for_completion"
* tag 'media/v4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] v4l: omap4iss: Replace outdated OMAP4 control pad API with syscon
[media] media: soc_camera: rcar_vin: Fix wait_for_completion
[media] marvell-ccic: fix Y'CbCr ordering
Since parse_perf_probe_point() deals with a user passed argument, we
should not assume it to be a valid string.
Without this patch, if pass '' to perf probe, a segfault raises:
$ perf probe -a ''
Segmentation fault
This patch checks argument of parse_perf_probe_point() before
string processing.
After this patch:
$ perf probe -a ''
usage: perf probe [<options>] 'PROBEDEF' ['PROBEDEF' ...]
or: perf probe [<options>] --add 'PROBEDEF' [--add 'PROBEDEF' ...]
...
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Zefan Li <lizefan@huawei.com>
Link: http://lkml.kernel.org/r/1430210769-94177-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
I spotted two (difficult to hit) bugs while reviewing this.
1) There is a double free bug because we unregister "map_kset" in
add_sysfs_runtime_map_entry() and also efi_runtime_map_init().
2) If we fail to allocate "entry" then we should return
ERR_PTR(-ENOMEM) instead of NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Guangyu Sun <guangyu.sun@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Single channel LVDS maxes out at 112 MHz. The 15" pre-retina models
shipped with 1440x900 (106 MHz) by default or 1680x1050 (119 MHz)
as a BTO option, both versions used dual channel LVDS even though
the smaller one would have fit into a single channel.
Notes:
Bug report showing that the MacBookPro8,2 with 1440x900 uses dual
channel LVDS (this lead to it being hardcoded in intel_lvds.c by
Daniel Vetter with commit 618563e394):
https://bugzilla.kernel.org/show_bug.cgi?id=42842
If i915.lvds_channel_mode=2 is missing even though the machine needs
it, every other vertical line is white and consequently, only the left
half of the screen is visible (verified by myself on a MacBookPro9,1).
Forum posting concerning a MacBookPro6,2 with 1440x900, author is
using i915.lvds_channel_mode=2 on the kernel command line, proving
that the machine uses dual channels:
https://bbs.archlinux.org/viewtopic.php?id=185770
Chi Mei N154C6-L04 with 1440x900 is a replacement panel for all
MacBook Pro "A1286" models, and that model number encompasses the
MacBookPro6,2 / 8,2 / 9,1. Page 17 of the panel's datasheet shows it's
driven with dual channel LVDS:
http://www.ebay.com/itm/-/400690878560http://www.everymac.com/ultimate-mac-lookup/?search_keywords=A1286http://www.taopanel.com/chimei/datasheet/N154C6-L04.pdf
Those three 15" models, MacBookPro6,2 / 8,2 / 9,1, are the only ones
with i915 graphics and dual channel LVDS, so that list should be
complete. And the 8,2 is already in intel_lvds.c.
Possible motivation to use dual channel LVDS even on the 1440x900
models: Reduce the number of different parts, i.e. use identical logic
boards and display cabling on both versions and the only differing
component is the panel.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
[Jani: included notes in the commit message for posterity]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Single channel LVDS maxes out at 112 MHz, anything above must be dual
channel. This avoids the need to specify i915.lvds_channel_mode=2 on
all 17" MacBook Pro models with i915 graphics since they had 1920x1200
(193 MHz), plus those 15" pre-retina models which had a resolution
of 1680x1050 (119 MHz) as a BTO option.
Source for 112 MHz limit of single channel LVDS is section 2.3 of:
https://01.org/linuxgraphics/sites/default/files/documentation/ivb_ihd_os_vol3_part4.pdf
v2: Avoid hardcoding 17" models by assuming dual channel LVDS if the
resolution necessitates it, suggested by Jani Nikula.
v3: Fix typo, thanks Joonas Lahtinen.
v4: Split commit in two, suggested by Ville Syrjälä.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
[Jani: included spec reference into the commit message]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This driver already makes use of ioremap_wc() on PIO buffers,
so convert it to use arch_phys_wc_add().
The qib driver uses a mmap() special case for when PAT is
not used, this behaviour used to be determined with a
module parameter but since we have been asked to just
remove that module parameter this checks for the WC cookie,
if not set we can assume PAT was used. If its set we do
what we used to do for the mmap for when MTRR was enabled.
The removal of the module parameter is OK given that Andy
notes that even if users of module parameter are still around
it will not prevent loading of the module on recent kernels.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Stefan Bader <stefan.bader@canonical.com>
Cc: konrad.wilk@oracle.com
Cc: ville.syrjala@linux.intel.com
Cc: david.vrabel@citrix.com
Cc: jbeulich@suse.com
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: infinipath@intel.com
Cc: linux-rdma@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xensource.com
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is no good reason not to, we eventually delete it as well.
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Mike Marciniszyn <infinipath@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
While unmapping an ODP writable page, the dirty bit of the page is set. In
order to do so, the head of the compound page is found.
Currently, the compound head is found even on non-writable pages, where it is
never used, leading to unnecessary cpu barrier that impacts performance.
This patch moves the search for the compound head to be done only when needed.
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Acked-by: Shachar Raindel <raindel@mellanox.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently, while mapping or unmapping pages for ODP, the umem mutex is locked
and unlocked once for each page. Such lock/unlock operation take few tens to
hundreds of nsecs. This makes a significant impact when mapping or unmapping few
MBs of memory.
To avoid this, the mutex should be locked only once per operation, and not per
page.
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Acked-by: Shachar Raindel <raindel@mellanox.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Get the actual (non-mapped) ip/tcp address of the connecting peer from
the port mapper
Also setup the passive side endpoint to correctly display the actual
and mapped addresses for the new connection.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Get the actual (non-mapped) ip/tcp address of the connecting peer from
the port mapper and report the address info to the user space application
at the time of connection establishment
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add functionality to enable the port mapper on the passive side to provide to its
clients the actual (non-mapped) ip/tcp address information of the connecting peer
1) Adding remote_info_cb() to process the address info of the connecting peer
The address info is provided by the user space port mapper service when
the connection is initiated by the peer
2) Adding a hash list to store the remote address info
3) Adding functionality to add/remove the remote address info
After the info has been provided to the port mapper client,
it is removed from the hash list
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently the iw_cxgb4 implementation requires the qp and cq qid densities
to match as well as the qp and cq id ranges. So fail a device open if
the device configuration doesn't meet the requirements.
The reason for these restictions has to do with the fact that IQ qid X
has a UGTS register in the same bar2 page as EQ qid X. Thus both qids
need to be allocated to the same user process for security reasons.
The logic that does this (the qpid allocator in iw_cxgb4/resource.c)
handles this but requires the above restrictions.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For T5, we must not use the kdb/kgts registers, in order avoid db drops
under extreme loads.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- get_dma_mr() was using ~0UL which is should be ~0ULL. This causes the
DMA MR to get setup incorrectly in hardware.
- wr_log_show() needed a 64b divide function div64_u64() instead of
doing
division directly.
- fixed warnings about recasting a pointer to a u64
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When accepting a new IPv4 connect to an IPv6 socket, the CMA tries to
canonize the address family to IPv4, but does not properly process
the listening sockaddr to get the listening port, and does not properly
set the address family of the canonized sockaddr.
Fixes: e51060f08a ("IB: IP address based RDMA connection manager")
Cc: <stable@vger.kernel.org>
Reported-By: Yotam Kenneth <yotamke@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A spinlock is regarded as contended when there is at least one waiter.
Currently, the code that checks whether there are any waiters rely on
tail value being greater than head. However, this is not true if tail
reaches the max value and wraps back to zero, so arch_spin_is_contended()
incorrectly returns 0 (not contended) when tail is smaller than head.
The original code (before regression) handled this case by casting the
(tail - head) to an unsigned value. This change simply restores that
behavior.
Fixes: d6abfdb202 ("x86/spinlocks/paravirt: Fix memory corruption on unlock")
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Cc: peterz@infradead.org
Cc: Waiman.Long@hp.com
Cc: borntraeger@de.ibm.com
Cc: oleg@redhat.com
Cc: raghavendra.kt@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1430799331-20445-1-git-send-email-tahsin@google.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The page_follow_link_light returns NULL and its error pointer was remained
in nd->path.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This reports performance regression by Yuanhan Liu.
The basic idea was to reduce one-point mutex, but it turns out this causes
another contention like context swithes.
https://lkml.org/lkml/2015/4/21/11
Until finishing the analysis on this issue, I'd like to revert this for a while.
This reverts commit 78373b7319.
Normally if driver is busy to dispatch a request the logic is like below:
block layer: driver:
__blk_mq_run_hw_queue
a. blk_mq_stop_hw_queue
b. rq add to ctx->dispatch
later:
1. blk_mq_start_hw_queue
2. __blk_mq_run_hw_queue
But it's possible step 1-2 runs between a and b. And since rq isn't in
ctx->dispatch yet, step 2 will not run rq. The rq might get lost if
there are no subsequent requests kick in.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When a FUA request enters its DATA stage of flush pipeline, the
request is added to mq requeue list, the request will then be added to
ctx->rq_list. blk_mq_attempt_merge() might merge the request with a bio.
Later when the request is finished the flush pipeline, the
request->__data_len is 0. Then I only saw the bio gets endio called, the
original request never finish.
Adding REQ_FLUSH_SEQ into REQ_NOMERGE_FLAGS looks an easy fix.
stable: 3.15+
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Hardware doesn't seem to work correctly, just block userspace in this case.
v2: add missing defines
Bugs: https://bugs.freedesktop.org/show_bug.cgi?id=85320
Signed-off-by: Christian König <christian.koenig@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The L3 Error handling on OMAP5 for the most part is very similar
to that of OMAP4, and had leveraged common data structures and
register layout definitions so far. Upon closer inspection, there
are a few minor differences causing an incorrect decoding and
reporting of the master NIU upon an error:
1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies
11 bits on OMAP5 as against 8 bits on OMAP4, with the master
NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR
field.
2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3
input sources on OMAP5. The common DEBUGSS source is at a
different input on each SoC.
Fix the above issues by using a OMAP5-specific compatible property
and using SoC-specific data where there are differences.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The base address for DRA7 CLK1_HOST_CLK1_2 host instance is
0x44800000, so correct offset is 0x800000. DRA7 TRM rev X(fewb 2015)
has updates for this information.
With wrong offset these errors are not correctly cleared by the L3
IRQ handler and cause an continuous interrupt scenario and system lockup.
Signed-off-by: Illia Smyrnov <illia.smyrnov@globallogic.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a typo in DRA7 dtsi where 12 bytes are needed for register
description of ABB efuse registers, however only 8 bytes are provided
to map. For some weird reason, this does not generate abort at offset
0x8, probably due to default maps already provided in io.c for the bus
register ranges.
Reported-by: Matt Gessner <Matt.Gessner@windriver.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 pre-production change includes switching the GPIO fan
gpio over from 1 to 2 to allow for a potential fix at a later point in
time for USB client VBUS detection using PMIC VBUS detect capability.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 pre-production change includes switching over to UART
pins that now allow for UART download capability. All original boards
should either have been returned for modifications or already modified
for the required change and maintaining compatibility for older boards
are no longer needed.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The new AM437x SK Beta boards have removed the
large capacitors on the gpio-matrix column lines
which means we can reduce col-scan-delay-us to 5us
without loosing functionality.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x Starter Kit uses a NewHaven Display module with
a 4.3" display and EDT FT5306 touchscreen
On that module's new revision, NewHave decided to change
the pinout on the 6 pin flat-pcb touchscreen connector so
that instead of having WAKE pin, we now have RESETn.
The new display module is available on AM437x SK Beta and
all new revisions while the older revision is only available
on AM437x SK Alpha which, unfortunately, can't be supported
anymore in mainline without a revert of this patch.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With commit bc078316d8 ("ARM: dts: DRA7: Add node for RTC"), we now
have AM57xx RTC register itself as alias 0 even before DS1307 or TPS
rtc drivers are loaded up. However, since neither TPS, nor AM57xx RTC
are capable of being backedup by battery, we would like to maintain
the "primary" rtc as mcp79410 rtc device.
This also generates the following warnings in the bootlog highlighting
the issue:
[ 5.895445] rtc-ds1307 2-006f: /aliases ID 0 not available
...
[ 6.476285] palmas-rtc 48070000.i2c:tps659038@58:tps659038_rtc: /aliases ID 1 not available
So, add proper aliases to ensure that RTC order is always consistent
to userspace immaterial of probe order.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The interrupt polarity provided in devicetree is used to configure
the interrupt controller(ARM GIC), however, it seems that we have an
inverter at the GIC boundary inside AM57xx which inverts the signal
input from sys_irq external interrupt source.
Further, as per GIC distributor TRM,
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438d/BGBHIACJ.html#BABJFCFB
ARM GIC distributor does not support IRQ trigger type
IRQ_TYPE_LEVEL_LOW, and only rising or level high signals.
However, for some reason, the current configuration(which gets ignored
by GIC driver) functions on some platforms, however, on few platforms
results in infinite interrupts hogging the system down.
Switch over to rising edge for GIC configuration which is also aligned
with trigger point from the RTC chip and the internal inversion.
Fixes: 5a0f93c657 ("ARM: dts: Add am57xx-beagle-x15")
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing #iommu-cells property to the isp and iva iommu nodes. This
fixes the binding (property is required according to the generic iommu
binding) and removes the following kernel warning triggered once the
iommu nodes are referenced:
[ 0.647521] /ocp/isp@480bc000: could not get #iommu-cells for /ocp/mmu@480bd400
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to enable EXTCON_USB_GPIO_USB and not
EXTCON_GPIO_USB.
Fixes: c08a54c0eb ("ARM: omap2plus_defconfig: Enable EXTCON_GPIO_USB")
Reported-by: Nishant Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by-by: Nishanth Menon <nm@ti.com
Tested-by: Nishanth Menon <nm@ti.com
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
N900 audio recording needs that codec provides bias voltage for integrated
digital microphone and headset microphone depending which one is used.
Digital microphone uses 2 V bias and it comes from the codec A part. Codec
B part drives the headset microphone bias and that is set to 2.5 V.
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[Jarkko: Headset mic bias changed to 2 (2.5 V) as it was before commit
e2e8bfdf61 ("ASoC: tlv320aic3x: Convert mic bias to a supply widget")]
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we use a combination of VMODE and I2C4 for retention modes,
eventually the off idle power consumption will creep up by about
23mW, even during off mode with I2C4 always staying enabled.
Turns out this is because of erratum i531 "Extra Power Consumed
When Repeated Start Operation Mode Is Enabled on I2C Interface
Dedicated for Smart Reflex (I2C4)" as pointed out by Nishanth
Menon <nm@ti.com>.
Let's fix the issue by adding i2c_cfg_clear_mask for the bits
to clear when initializing the I2C4 adapter so we can clear
SREN bit that drives the I2C4 lines low otherwise when there
is no traffic.
Fixes: 3b8c4ebb76 ("ARM: OMAP3: Fix idle mode signaling for
Cc: stable@vger.kernel.org # v3.16+
sys_clkreq and sys_off_mode")
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
