This adds code to look at the properties firmware puts in the device
tree to determine what compatibility mode the partition is in on
POWER6 machines, and set the ELF aux vector AT_HWCAP and AT_PLATFORM
entries appropriately.
Specifically, we look at the cpu-version property in the cpu node(s).
If that contains a "logical" PVR value (of the form 0x0f00000x), we
call identify_cpu again with this PVR value. A value of 0x0f000001
indicates the partition is in POWER5+ compatibility mode, and a value
of 0x0f000002 indicates "POWER6 architected" mode, with various
extensions disabled. We also look for various other properties:
ibm,dfp, ibm,purr and ibm,spurr.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PPU event-based and cycle-based profiling support to Oprofile for Cell.
Oprofile is expected to collect data on all CPUs simultaneously.
However, there is one set of performance counters per node. There are
two hardware threads or virtual CPUs on each node. Hence, OProfile must
multiplex in time the performance counter collection on the two virtual
CPUs.
The multiplexing of the performance counters is done by a virtual
counter routine. Initially, the counters are configured to collect data
on the even CPUs in the system, one CPU per node. In order to capture
the PC for the virtual CPU when the performance counter interrupt occurs
(the specified number of events between samples has occurred), the even
processors are configured to handle the performance counter interrupts
for their node. The virtual counter routine is called via a kernel
timer after the virtual sample time. The routine stops the counters,
saves the current counts, loads the last counts for the other virtual
CPU on the node, sets interrupts to be handled by the other virtual CPU
and restarts the counters, the virtual timer routine is scheduled to run
again. The virtual sample time is kept relatively small to make sure
sampling occurs on both CPUs on the node with a relatively small
granularity. Whenever the counters overflow, the performance counter
interrupt is called to collect the PC for the CPU where data is being
collected.
The oprofile driver relies on a firmware RTAS call to setup the debug bus
to route the desired signals to the performance counter hardware to be
counted. The RTAS call must set the routing registers appropriately in
each of the islands to pass the signals down the debug bus as well as
routing the signals from a particular island onto the bus. There is a
second firmware RTAS call to reset the debug bus to the non pass thru
state when the counters are not in use.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following routines are added to arch/powerpc/platforms/cell/pmu.c:
cbe_clear_pm_interrupts()
cbe_enable_pm_interrupts()
cbe_disable_pm_interrupts()
cbe_query_pm_interrupts()
cbe_pm_irq()
cbe_init_pm_irq()
This also adds a routine in arch/powerpc/platforms/cell/interrupt.c and
some macros in cbe_regs.h to manipulate the IIC_IR register:
iic_set_interrupt_routing()
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move some PMU-related macros and function prototypes from cbe_regs.h
and pmu.h in arch/powerpc/platforms/cell/ to a new header at
include/asm-powerpc/cell-pmu.h
This is cleaner to use from the oprofile code, since that sits in
arch/powerpc/oprofile, not in the cell platform directory.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
More macros for manipulating bits in the Cell PMU control registers.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add symbol-exports for the new routines in arch/powerpc/platforms/cell/pmu.c.
They are needed for Oprofile, which can be built as a module.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In order to fit with the "don't-run-spus-outside-of-spu_run" model, this
patch starts the isolated-mode loader in spu_run, rather than
spu_create. If spu_run is passed an isolated-mode context that isn't in
isolated mode state, it will run the loader.
This fixes potential races with the isolated SPE app doing a
stop-and-signal before the PPE has called spu_run: bugzilla #29111.
Also (in conjunction with a mambo patch), this addresses #28565, as we
always set the runcntrl register when entering spu_run.
It is up to libspe to ensure that isolated-mode apps are cleaned up
after running to completion - ie, put the app through the "ISOLATE EXIT"
state (see Ch11 of the CBEA).
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This change adds a read accessor for the SPE problem-state run control
register.
This is required for for applying (userspace) changes made to the run
control register while the SPE is stopped - simply asserting the master
run control bit is not sufficient. My next patch for isolated-mode
setup requires this.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When the user changes the runcontrol register, an SPU might be
running without a process being attached to it and waiting for
events. In order to prevent this, make sure we always disable
the priv1 master control when we're not inside of spu_run.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When fixing spufs to map the 'mem' file backing store cacheable,
I incorrectly set the physical mapping to use both cache-inhibited
and guarded mapping, which resulted in a serious performance
degradation.
Debugged-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When one of the spufs files is mapped into a process address
space, regular users can use ptrace to attempt accessing
them with access_process_vm(). With the way that the
mappings currently work, this likely causes an oops.
Setting the vm_flags to VM_IO makes sure that ptrace can
not access them but returns an error code. This is not
the perfect solution in case of the local store mapping,
but it fixes the oops in a well-defined way.
Also remove leftover VM_RESERVED flags in spufs. The
VM_RESERVED flag is on it's way out and not checked by
the memory managment code anymore.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Christoph Hellwig <chellwig@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When there is pending signals, current spufs_run_spu() always returns
-ERESTARTSYS and it is called again automatically.
But, if spe already stopped by stop-and-signal or halt instruction,
returning -ERESTARTSYS makes stop-and-signal/halt lost and
spu run over the end-point.
For your convenience, I attached a sample code to restage this bug.
If there is no bug, printed NPC will be 0x4000.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we attempt an MFC DMA to an unmapped address, the event
returned from spu_run should be SPE_EVENT_SPE_DATA_STORAGE,
not SPE_EVENT_INVALID_DMA.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace the use of the platform specific variable spu.nid with the
platform independednt variable spu.node.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to check the channel count of the signal notification registers
before reading them, because it can be undefined when the count is
zero. In order to read count and data atomically, we read from the
saved context.
This patch uses spu_acquire_saved() to force a context save before a
/signal1 or /signal2 read. Because of this it is no longer necessary to
have backing_ops and hw_ops versions of this function so they have been
removed.
Regular applications should not rely on reading this register
to be fast, as it's conceptually a write-only file from the PPE
perspective.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch implements read only access to
/mbox_info - SPU Write Outbound Mailbox
/ibox_info - SPU Write Outbound Interrupt Mailbox
/wbox_info - SPU Read Inbound Mailbox
These files are used by gdb in order to look into the current mailbox
queues without changing the contents at the same time. They are
not meant for general programming use, since the access requires
a context save and is therefore rather slow.
It would be good to complement this patch with one that adds
write support as well.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes the /spu_tag_mask file from spufs. The data provided by
this file is also available from the /dma_info file in the dma_info_mask
of the spu_dma_info struct.
The file was intended to be used by gdb, but that never used it, and
now it has been replaced with the more verbose dma_info file.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The /lslr file gives read access to the SPU_LSLR register in hex; 0x3fff
for example The /dma_info file provides read access to the SPU Command
Queue in a binary format. The /proxydma_info files provides read access
access to the Proxy Command Queue in a binary format. The spu_info.h
file provides data structures for interpreting the binary format of
/dma_info and /proxydma_info.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patches changes /npc, /decr, /decr_status, /spu_tag_mask,
/event_mask, /event_status, and /srr0 files to provide output according to
the format string "0x%llx" instead of "%llx".
Before this patch some files used "0x%llx" and other used "%llx" which is
inconsistent and potentially confusing. A user might assume "%llx" numbers
were decimal if they happened to not contain any a-f digits. This change
will break any code cannot tolerate a leading 0x in the file contents. The
only known users of these files are the libspe but there might also be
some scripts which access these files. This risk is deemed acceptable for
future consistency.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SCC parameter RAM areas are mapped wrong in MPC8xx device descriptions. All
memory areas overlap with the next one, so that I2C, SPI, SMC1 and SMC2 cannot
be enabled if the four SCCs are.
Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/sysdev/mpc52xx_pic.c breaks the ppc build
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch below fixes an arithmetic wrap-around issue on 32bit machines
using smp-tbsync. Without this patch a timebase value over
0x000000007fffffff will hang the boot process while bringing up
secondary CPUs.
Signed-off-by: Adrian Cox <adrian@humboldt.co.uk>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes 2 changes to clean up the flat device tree handling
logic in the zImage wrapper.
First, there were two callbacks from the dt_ops structure used for
producing a final flat tree to pass to the kerne: dt_ops.ft_pack()
which packed the flat tree (possibly a no-op) and dt_ops.ft_addr()
which retreived the address of the final blob. Since they were only
ever called together, this patch combines the two into a single new
callback, dt_ops.finalize(). This new callback does whatever
platform-dependent things are necessary to produce a final flat device
tree blob, and returns the blob's addres.
Second, the current logic calls the kernel with a flat device tree if
one is build into the zImage wrapper, otherwise it boots the kernel
with a PROM pointer, expecting the kernel to copy the OF device tree
itself. This approach precludes the possibility of the platform
wrapper code building a flat device tree from whatever
platform-specific information firmware provides. Thus, this patch
takes the more sensible approach of invoking the kernel with a flat
tree if the dt_ops.finalize callback provides one (by whatever means).
So, the dt_ops.finalize callback can be NULL, or can be a function
which returns NULL. In either case, the zImage wrapper logic assumes
that this is a platform with OF and invokes the kernel accordingly.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes the handling of the initrd (or initramfs) in the
zImage wrapper a little easier to follow. Instead of passing the
initrd addresses out from prep_kernel() via the cryptic a1 and a2
parameters, use the global struct add_range, 'initrd'. prep_kernel()
already passes information through the 'vmlinux' addr_range struct, so
this seems like a reasonable extension.
Some comments also clarify the logic with prep_kernel(): we use an
initrd included in the zImage if present, otherwise we use an initrd
passed in by the bootloader in the a1 and a2 parameters (yaboot, at
least, uses this mechanism to pass an initrd).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Per email discussion, it appears that rtas_stop_self()
and pSeries_mach_cpu_die() should not be compiled if
CONFIG_HOTPLUG_CPU is not defined. This patch adds
#ifdefs around these bits of code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch adds a tsi108/9 pci interrupt controller host.
On mpc7448hpc2 board, pci_irq_fixup function is removed, which makes the
pci_read_irq_line be the default pci irq fixup.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix compilation without PCI support for Bubinga, CPCI405 and EP405.
bios_fixup() for these boards uses functions available only with
CONFIG_PCI, so linker fails.
Signed-off-by: Wojtek Kaniewski <wojtekka@toxygen.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PPC/booke reg MCSR value misquoted
Signed-off-by: nkalmala <nkalmala@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rewrite local_get_flags and local_irq_disable to use r13 explicitly,
to avoid the risk that gcc will split get_paca()->soft_enabled into a
sequence unsafe against preemption. Similar care in local_irq_restore.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Merge 32 and 64 bits asm-powerpc/io.h
The rework on io.h done for the new hookable accessors made it easier,
so I just finished the work and merged 32 and 64 bits io.h for arch/powerpc.
arch/ppc still uses the old version in asm-ppc, there is just too much gunk
in there that I really can't be bothered trying to cleanup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In order to suppose platforms with devices above 4Gb on 32 bits platforms
with a >32 bits physical address space, we used to have a special ioremap64
along with a fixup routine fixup_bigphys_addr.
This shouldn't be necessary anymore as struct resource now supports 64 bits
addresses even on 32 bits archs. This patch enables that option when
CONFIG_PHYS_64BIT is set and removes ioremap64 and fixup_bigphys_addr.
This is a preliminary work for the upcoming merge of 32 and 64 bits io.h
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds full cell iommu support (and iommu disabled mode).
It implements mapping/unmapping of iommu pages on demand using the
standard powerpc iommu framework. It also supports running with
iommu disabled for machines with less than 2GB of memory. (The
default is off in that case, though it can be forced on with the
kernel command line option iommu=force).
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that the direct DMA ops supports an offset, we use that instead
of defining our own.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes dma_alloc_coherent() use node local allocation when
using the direct DMA ops. The node is obtained from the new device
extension. If no such extension is present, the current node is used.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds an optional global offset that can be added to DMA addresses
when using the direct DMA operations.
That brings it a step closer to the 32 bits direct DMA operations, and makes
it useable on Cell when the MMU is disabled and we are using a spider
southbridge.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch implements a workaround for a Spider PCI host bridge bug
where it doesn't enforce some of the PCI ordering rules unless some
manual manipulation of a special register is done. In order to be
fully compliant with the PCI spec, I do this on every MMIO read
operation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way iSeries hooks on PCI IO operations (both MMIO
and PIO) and provides a generic way for other platforms to do so (we
have need to do that for various other platforms).
While reworking the IO ops, I ended up doing some spring cleaning in
io.h and eeh.h which I might want to split into 2 or 3 patches (among
others, eeh.h had a lot of useless stuff in it).
A side effect is that EEH for PIO should work now (it used to pass IO
ports down to the eeh address check functions which is bogus).
Also, new are MMIO "repeat" ops, which other archs like ARM already had,
and that we have too now: readsb, readsw, readsl, writesb, writesw,
writesl.
In the long run, I might also make EEH use the hooks instead
of wrapping at the toplevel, which would make things even cleaner and
relegate EEH completely in platforms/iseries, but we have to measure the
performance impact there (though it's really only on MMIO reads)
Since I also need to hook on ioremap, I shuffled the functions a bit
there. I introduced ioremap_flags() to use by drivers who want to pass
explicit flags to ioremap (and it can be hooked). The old __ioremap() is
still there as a low level and cannot be hooked, thus drivers who use it
should migrate unless they know they want the low level version.
The patch "arch provides generic iomap missing accessors" (should be
number 4 in this series) is a pre-requisite to provide full iomap
API support with this patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes the Cell DMA code work on both the Spider and the Axon
south bridges by turning cell_dma_valid into a variable instead of a
constant. This is a temporary patch until we have full iommu support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When enabled in Kconfig, it will pick up any of_platform_device
matching it's match list (currently type "pci", "pcix", "pcie",
or "ht" and setup a PHB for it.
Platform must provide a ppc_md.pci_setup_phb() for it to work
(for doing the necessary initialisations specific to a given PHB
like setting up the config space ops).
It's currently only available on 64 bits as the 32 bits PCI code
can't quite cope with it in it's current form. I will fix that
later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a "parent" struct device to our PCI host bridge data structure so that
PCI can be rooted off another device in sysfs.
Note that arch/ppc doesn't use it, only arch/powerpc, though it's available
for both 32 and 64 bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The BUID is the first entry of a PCI host bridge "reg" property.
Now that PCI busses can be anywhere in the device-tree, we need to
fully translate the value there to a CPU physical address before
we can use it with RTAS.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When parsing the OF "ranges" properties of PCI host busses to determine
the mapping of a PCI bus, we need to translate the "parent" address using
the prom_parse.c routines in order to obtain a CPU physical address.
This wasn't necessary while PCI busses were always at the root of the
device-tree but this is no longer the case on Cell where they can be
anywhere in the tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a bus device notifier to the of_platform bus type on
cell to setup the DMA operations for of_platform_devices. We currently
use the PCI operations as Cell use a special version of them that
happens to be suitable for our needs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch completely refactors DMA operations for 64 bits powerpc. 32 bits
is untouched for now.
We use the new dev_archdata structure to add the dma operations pointer
and associated data to struct device. While at it, we also add the OF node
pointer and numa node. In the future, we might want to look into merging
that with pci_dn as well.
The old vio, pci-iommu and pci-direct DMA ops are gone. They are now replaced
by a set of generic iommu and direct DMA ops (non PCI specific) that can be
used by bus types. The toplevel implementation is now inline.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Hook up of_platform_bus_probe with the cell platform in order to publish
the non-PCI devices in the device-tree of cell blades as of_platform_device(s)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch first splits of_device.c and of_platform.c, the later containing
the bits relative to of_platform_device's. On the "breaks" side of things,
drivers uisng of_platform_device(s) need to include asm/of_platform.h now
and of_(un)register_driver is now of_(un)register_platform_driver.
In addition to a few utility functions to locate of_platform_device(s),
the main new addition is of_platform_bus_probe() which allows the platform
code to trigger an automatic creation of of_platform_devices for a whole
tree of devices.
The function acts based on the type of the various "parent" devices encountered
from a provided root, using either a default known list of bus types that can be
"probed" or a passed-in list. It will only register devices on busses matching
that list, which mean that typically, it will not register PCI devices, as
expected (since they will be picked up by the PCI layer).
This will be used by Cell platforms using 4xx-type IOs in the Axon bridge
and can be used by any embedded-type device as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support for southbridges using the MPIC interrupt controller to
the native cell platforms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch applies on top of the MPIC DCR support. It makes the MPIC
driver capable of a lot more auto-configuration based on the device-tree,
for example, it can retreive it's own physical address if not passed as
an argument, find out if it's DCR or MMIO mapped, and set the BIG_ENDIAN
flag automatically in the presence of a "big-endian" property in the
device-tree node.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch implements support for DCR based MPIC implementations. Such
implementations have the MPIC_USES_DCR flag set and don't use the phys_addr
argument of mpic_alloc (they require a valid dcr mapping in the device node)
This version of the patch can use a little bif of cleanup still (I can
probably consolidate rb->dbase/doff, at least once I'm sure on how the
hardware is actually supposed to work vs. possible simulator issues) and
it should be possible to build a DCR-only version of the driver. I need
to cleanup a bit the CONFIG_* handling for that and probably introduce
CONFIG_MPIC_MMIO and CONFIG_MPIC_DCR.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds new dcr_map/dcr_read/dcr_write accessors for DCRs that
can be used by drivers to transparently address either native DCRs or
memory mapped DCRs. The implementation for memory mapped DCRs is done
after the binding being currently worked on for SLOF and the Axon
chipset. This patch enables it for the cell native platform
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These were inherited from ARCH=ppc, but are not needed since parsing of interrupts
should be done via the of_* functions (who can do swizzling). If we ever need to
do non-standard swizzling on bridges without a device-node, then we might add
back a slightly different version of ppc_md.pci_swizzle but for now, that is not
the case.
I removed the couple of calls for these in 83xx. If that breaks something, then
there is a problem with the device-tree on these.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way IRQs are fixed up on PCI for arch powerpc.
It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().
It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.
I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.
I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* sanitize prototypes, annotate
* usual ntohs->shift
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes, annotate
* collapse csum_partial_copy
* usual ntohs->shift
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes, annotate
* kill csum_partial_copy_fromuser
* kill shift-by-16 in checksum calculations
* ntohs->shift in checksum calculations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes, annotate
* collapse csum_partial_copy
* kill csum_partial_copy_fromuser
* ntohs->shift in checksum calculation
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitized prototypes, annotated
* kill shift-by-16 in checksum calculation
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes, annotate
* kill shift-by-16 in checksum calculations
* htons->shift in l-e checksum calculations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes, annotated
* collapsed csum_partial_copy()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes, annotate
* ntohs -> shift in checksum calculations in l-e case
* kill shift-by-16 in checksum calculations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes, annotate
* ntohs -> shift in checksum calculations
* kill access_ok() in csum_partial_copy_from_user
* collapse do_csum_partial_copy_from_user
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes and annotate
* collapse csum_partial_copy
NB: csum_partial() is almost certainly still buggy.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes and annotate
* collapse csum_partial_copy
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes and annotate
* kill cast-as-lvalue abuses in csum_partial()
* usual ntohs-equals-shift for checksum purposes
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes and annotate
* kill useless access_ok() in csum_partial_copy_from_user() (the only
caller checks it already).
* do_csum_partial_copy_from_user() is not needed now
* replace htons(len) with len << 8 - they are the same wrt checksums
on little-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 281ea49b0c,
which broke ACPI Interrupt source overrides that move
the SCI from one IRQ in PIC mode to another in IOAPIC mode.
If the SCI shared an interrupt line with another device,
this would result in a "irq 18: nobody cared" type failure.
http://bugzilla.kernel.org/show_bug.cgi?id=7601
Signed-off-by: Len Brown <len.brown@intel.com>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (31 commits)
[MIPS] Remove duplicate ISA DMA code for 0 DMA channel case.
[MIPS] Remove unused definition of cpu_to_lelongp()
[MIPS] Remove userspace proofing from <asm/bitops.h>.
[MIPS] Remove old junk left from old atomic_lock.
[MIPS] Use conditional traps for BUG_ON on MIPS II and better.
[MIPS] mips HPT cleanup: make clocksource_mips public
[MIPS] do_IRQ cleanup
[MIPS] Avoid dupliate D-cache flush on R400C / R4400 SC and MC variants.
[MIPS] Remove redundant r4k_blast_icache() calls
[MIPS] Work around bogus gcc warnings.
[MIPS] Fix double inclusions
[MIPS] use generic_handle_irq, handle_level_irq, handle_percpu_irq
[MIPS] IRQ cleanups
[MIPS] mips hpt cleanup: get rid of mips_hpt_init
[MIPS] PB1200: Remove duplicate definitions
[MIPS] Fix alignment hole in struct cache_desc; shrink struct.
[MIPS] Oprofile: kernel support for the R10000.
[MIPS] Remove unused R10000 performance counter definitions.
[MIPS] Add support for kexec
[MIPS] Don't print presence of WAIT instruction on bootup.
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
Driver core: show drivers in /sys/module/
Documentation/driver-model/platform.txt update/rewrite
Driver core: platform_driver_probe(), can save codespace
driver core: Use klist_remove() in device_move()
driver core: Introduce device_move(): move a device to a new parent.
Driver core: make drivers/base/core.c:setup_parent() static
driver core: Introduce device_find_child().
sysfs: sysfs_write_file() writes zero terminated data
cpu topology: consider sysfs_create_group return value
Driver core: Call platform_notify_remove later
ACPI: Change ACPI to use dev_archdata instead of firmware_data
Driver core: add dev_archdata to struct device
Driver core: convert sound core to use struct device
Driver core: change mem class_devices to be real devices
Driver core: convert fb code to use struct device
Driver core: convert firmware code to use struct device
Driver core: convert mmc code to use struct device
Driver core: convert ppdev code to use struct device
Driver core: convert PPP code to use struct device
Driver core: convert cpuid code to use struct device
...
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global pci_bf_sort static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updated patch adds the Intel ICH9 LPC and SMBus Controller DID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Tested (compilation only):
- using allmodconfig
- making sure the files are compiling without any warning/error due to
new changes
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mostly CodingStyle cleanups for arch/i386/pci/i386.c:
- fit in 80 columns;
- use a #defined value instead of an inline constant;
Also change one resource_size_t (DBG) printk from %08lx to %lx since
it can be more than 32 bits (more than 8 hexits).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support a shadowed ROM when running with an ACPI capable PROM.
Define a new dev.resource flag IORESOURCE_ROM_BIOS_COPY to
describe the case of a BIOS shadowed ROM, which can then
be used to avoid pci_map_rom() making an unneeded call to
pci_enable_rom().
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
First phase in introducing ACPI support to SN.
In this phase, when running with an ACPI capable PROM,
the DSDT will define the root busses and all SN nodes
(SGIHUB, SGITIO). An ACPI bus driver will be registered
for the node devices, with the acpi_pci_root_driver being
used for the root busses. An ACPI vendor descriptor is
now used to pass platform specific information for both
nodes and busses, eliminating the need for the current
SAL calls. Also, with ACPI support, SN fixup code is no longer
needed to initiate the PCI bus scans, as the acpi_pci_root_driver
does that.
However, to maintain backward compatibility with non-ACPI capable
PROMs, none of the current 'fixup' code can been deleted, though
much restructuring has been done. For example, the bulk of the code
in io_common.c is relocated code that is now common regardless
of what PROM is running, while io_acpi_init.c and io_init.c contain
routines specific to an ACPI or non ACPI capable PROM respectively.
A new pci bus fixup platform vector has been created to provide
a hook for invoking platform specific bus fixup from pcibios_fixup_bus().
The size of io_space[] has been increased to support systems with
large IO configurations.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This file no longer uses pci_cache_line_size, so delete the declaration
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The setting of the CACHE_LINE_SIZE register in sparc64's pci
initialisation code isn't quite adequate as the device may have
incompatible requirements. The generic code tests for this, so switch
sparc64 over to using it.
Since sparc64 has different L1 cache line size and PCI cache line size,
it would need to override the generic code like i386 and ia64 do. We
know what the cache line size is at compile time though, so introduce a
new optional constant PCI_CACHE_LINE_BYTES.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pci_generic_prep_mwi() code does everything that pcibios_prep_mwi()
does on ia64. All we need to do is be sure that pci_cache_line_size
is set appropriately, and we can delete pcibios_prep_mwi().
Using SMP_CACHE_BYTES as the default was wrong on uniprocessor machines
as it is only 8 bytes. The default in the generic code of L1_CACHE_BYTES
is at least as good.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The number of permutations of crap we do is amazing and almost all of it
has the wrong effect in 2.6.
At the heart of this is the PCI SFF magic which says that compatibility
mode PCI IDE controllers use ISA IRQ routing and hard coded addresses
not the BAR values. The old quirks variously clears them, sets them,
adjusts them and then IDE ignores the result.
In order to drive all this garbage out and to do it portably we need to
handle the SFF rules directly and properly. Because we know the device
BAR 0-3 are not used in compatibility mode we load them with the values
that are implied (and indeed which many controllers actually
thoughtfully put there in this mode anyway).
This removes special cases in the IDE layer and libata which now knows
that bar 0/1/2/3 always contain the correct address. It means our
resource allocation map is accurate from boot, not "mostly accurate"
after ide is loaded, and it shoots lots of code. There is also lots more
code and magic constant knowledge to shoot once this is in and settled.
Been in my test tree for a while both with drivers/ide and with libata.
Wants some -mm shakedown in case I've missed something dumb or there are
corner cases lurking.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Changes persistant -> persistent. www.dictionary.com does not know
persistant (with an A), but should it be one of those things you can
spell in more than one correct way, let me know.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix various .c/.h typos in comments (no code changes).
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix various Kconfig typos.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Make clocksource_mips public and get rid of mips_hpt_read,
mips_hpt_mask.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now we have both function and macro version of do_IRQ() and the former
is used only by DEC and non-preemptive kernel. This patch makes
everyone use the macro version and removes the function version.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
