Commit graph

157152 commits

Author SHA1 Message Date
Anil Veerabhadrappa
c19dcd0112 [SCSI] bnx2i : Fix "cid #n not valid" issue
When bnx2i_adapter_ready() fails, connection handle(cid) = 0 is wrongly freed
because 'cid' is not yet allocated for the endpoint.  Fix is to initialize
bnx2i_ep->ep_iscsi_cid to '-1' in bnx2i_alloc_ep() and not in
bnx2i_ep_connect() to avoid releasing invalid 'cid'.  There is already a check
in bnx2i_free_iscsi_cid() not to free invalid iscsi connection handle (-1)

Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:12 -05:00
Anil Veerabhadrappa
534cc9c165 [SCSI] bnx2i : Fix command session number jump issue seen during cable pull test
Without the fix bnx2i would fail tt->xmit_task() when link is down and
libiscsi would have already incremented session->cmdsn before calling bnx2i's
xmit_task() entry point and will just return the command to SCSI-ML when
xmit_task() fails. libiscsi does not retract the session->cmdsn as the command
was never sent on wire.  It is generally good idea for LLD, bnx2i to accept
the scsi cmnd/nopout and let upper layer timeout and go though normal session
recovery process.  When link is down, unsolicited nopout will not be accepted
by bnx2i and connection will never enter recovery state. This fix is required
for MPIO to work corectly

Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:11 -05:00
Vasu Dev
1d1b88dc01 [SCSI] fcoe: removes phys_dev and renames real_dev to netdev.
The phys_dev was used only to locate common offload EM instance for all
FCoE instances on a eth devices in function fcoe_em_config, so just updated
fcoe_em_config to look for actual real eth device in locating common offload
EM instance and then no need to store phys_dev in fcoe_softc, so removes
phys_dev from fcoe_softc also.

Renames fcoe_softc real_dev to netdev and updates all its uses to use netdev.

So effectively no functional change, use of single netdev instead phys_dev
and real_dev saves one pointer memory in fcoe_softc, also real_dev used here
was confusing with vlan driver terminology since real_dev in vlan driver is
referred to physical eth device.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:11 -05:00
Yi Zou
53fcfbbef5 [SCSI] libfc: Remove page flags check for sglist
I don't believe this check is needed any more in the current kernel, which,
if I understand correctly, is for compound page where only the first page
is supposed to get ref-counted.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:10 -05:00
Yi Zou
537029f8e9 [SCSI] libfc: Remove FC_FRAME_SG_LEN in fc_fcp_send_data
FC_FRAME_SG_LEN is 4 which is too small when offload is enabled. Actually, the
WARN_ON() in fc_fcp_send_data() should be:

	WARN_ON(skb_shinfo(fp_skb(fp))->nr_frags > MAX_SKB_FRAGS);

But since we will not get anything more than 64K anyway, so there is no need
to do this anyway here. Therefore, I am getting rid of FC_FRAME_SG_LEN here
and the WARN_ON here.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:10 -05:00
Yi Zou
15a521b424 [SCSI] fcoe: Remove ifdef for NETIF_F_FCOE_CRC and NETIF_F_FSO
Remove the extra ifdef for NETIF_F_FSO and NETIF_F_FCOE_CRC since they are
already defined in the current kernel as in include/linux/netdevice.h.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:10 -05:00
Vasu Dev
d7179680d0 [SCSI] fcoe, libfc: adds offload EM per eth device with only single xid range per EM
Updates fcoe_em_config to allocate a single instance of sharable offload
EM for supported lp->lro_xid per eth device, and then share this EM
for subsequently more lports creation on same eth device (e.g when using
VLAN).

Adds tiny fcoe_oem_match function for offload EM to return true for read
types IO to have read IO exchanges allocated from offload shared EM.

Removes fc_em_alloc_xid function completely which was needed to manage
two xid ranges within a EM, this is not needed any more with allocation
of separate sharable offload EM per eth device. Instead this patch adds
simple xid allocation logic to manage single xid range.

Adds fc_exch_em_alloc with mp->next_xid as cursor to allocate new xid
from single xid range of EM, uses mp->next_xid instead removed mp->last_xid
which slightly increase probability of finding empty xid on exch allocation.

Removes restriction of not allowing use of xid zero along with changing
two xid range change to single xid range.

Makes fc_fcp_ddp_setup calling conditional to only xid allocated from
shared offload EM.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:09 -05:00
Vasu Dev
e8af4d4380 [SCSI] fcoe: modifies fcoe_hostlist_lock uses as prep work to add shared offload EM
Modifies fcoe_hostlist_lock uses such that a new EM allocation in
fcoe_em_config and adding new fcoe_softc using fcoe_hostlist_add
are atomic, this is to ensure that a shared offload EM gets allocated
only once per eth device for its all lports.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:09 -05:00
Vasu Dev
52ff878c91 [SCSI] fcoe, fnic, libfc: modifies current code paths to use EM anchor list
Modifies current code to use EM anchor list in EM allocation, EM free,
EM reset, exch allocation and exch lookup code paths.

 1. Modifies fc_exch_mgr_alloc to accept EM match function and then
    have allocated EM added to the lport using fc_exch_mgr_add API
    while also updating EM kref for newly added EM.

 2. Updates fc_exch_mgr_free API to accept only lport pointer instead
    EM and then have this API free all EMs of the lport from EM anchor
    list.

 3. Removes single lport pointer link from the EM, which was used in
    associating lport pointer in newly allocated exchange. Instead have
    lport pointer passed along new exchange allocation call path and
    then store passed lport pointer in newly allocated exchange, this
    will allow a single EM instance to be used across more than one
    lport and used in EM reset to reset only lport specific exchanges.

 4. Modifies fc_exch_mgr_reset to reset all EMs from the EM anchor list
    of the lport, adds additional exch lport pointer (ep->lp) check for
    shared EM case to reset exchange specific to a lport requested reset.

 5. Updates exch allocation API fc_exch_alloc to use EM anchor list and
    its anchor match func pointer. The fc_exch_alloc will walk the list
    of EMs until it finds a match, a match will be either null match
    func pointer or call to match function returning true value.

 6. Updates fc_exch_recv to accept incoming frame on local port using
    only lport pointer and frame pointer without specifying EM instance
    of incoming frame. Instead modified fc_exch_recv to locate EM for the
    incoming frame by matching xid of incoming frame against a EM xid range.
    This change was required to use EM list in libfc Rx path and after this
    change the lport fc_exch_mgr pointer emp is not needed anymore, so
    removed emp pointer.

 7. Updates fnic for removed lport emp pointer and above modified libfc APIs
    fc_exch_recv, fc_exch_mgr_alloc and fc_exch_mgr_free.

 8. Removes exch_get and exch_put from libfc_function_template as these
    are no longer needed with EM anchor list and its match function use.
    Also removes its default function fc_exch_get.

A defect this patch introduced regarding the libfc initialization order in
the fnic driver was fixed by Joe Eykholt <jeykholt@cisco.com>.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:08 -05:00
Robert Love
d459b7ea1b [SCSI] libfc: Remove the FC_EM_DBG macro
Currently there is a 1:1 relationship between the lport
and exchange manager. This macro takes an EM as an argument
and determines the lport from it. However, later patches
will use an EM list per lport, so we will no longer have
this 1:1 relationship- this macro must change.

The FC_EM_DBG macro is rarely used. There are four callers,
two can use FC_LPORT_DBG instead and two can be removed
since they're not necessary. This patch makes those changes
and removes the macro.

Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:08 -05:00
Vasu Dev
96316099ac [SCSI] fcoe, libfc: adds exchange manager(EM) anchor list per lport and related APIs
Adds EM list using a anchor struct fc_exch_mgr_anchor, anchor is used
to allow same EM instance sharing across more than one lport on a eth
device, this implementation is per discussed design posted at
http://www.open-fcoe.org/pipermail/devel/2009-June/002566.html.

The shared EM is required for multiple lports on eth device when
using multiple VLANs or NPIV.

Adds fc_exch_mgr_add API to add a EM to the lport and fc_exch_mgr_del
API to delete previously added EM.

Also adds function fc_exch_mgr_destroy() to destroy allocated EM.
The kref is added to the EM to keep track of EM usage count, the EM is
destroyed when no longer in use upon kref reaching to zero.

The caller can specify match function to fc_exch_mgr_add, this
will be used in determining exchange allocation from its EM or not.

Moved calling of fcoe_em_config below fcoe_libfc_config calling,
so that list head lp->ema_list is initialized before configuring
EM.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:07 -05:00
Joe Eykholt
201e5795b7 [SCSI] libfc: fix: cancel rport retry timer
The timer for rport retries wasn't getting canceled, and
would occasionally go off after the module was unloaded.

Add logic to cancel the timer in fc_rport_work().

Since we cancel the timer before deleting the rdata,
it is no longer necessary to do a get_device() for the pending timer.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:07 -05:00
Joe Eykholt
5f7ea3b7f8 [SCSI] libfc: fc_rport_logoff should not drop the lock
fc_rport_logoff drops the rport lock in order to cancel work
that may be pending.  This is undesirable as the state can
completely change, and the caller may not expect that the
lock could've been dropped.

If there is work pending, it will acquire the rdata mutex and
so we're protected and can change the event from READY to DELETE.
Queue the work only if there is no event already pending.

There were a couple other cases where the state was set to
DELETE and work queued, even though the state may have already
been DELETE.  Fix these using a common function fc_rport_enter_delete().

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:06 -05:00
Joe Eykholt
141940548c [SCSI] libfc: rename rport state "NONE" to "DELETE".
State RPORT_ST_NONE was intented to be an invalid state (0), never used.
This was a misguided attempt to be sure it was always initialized.
Having an extra state meaning nothing requires switch statements to
have a case covering that state.

State NONE has been used instead to mean the remote port is being deleted.
Changing the name to RPORT_ST_DELETE.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:06 -05:00
Joe Eykholt
84b05445b9 [SCSI] libfc: fix WARNING from fc_seq_start_next on closed exchanges
We saw periodic messages like:

WARNING: at drivers/scsi/libfc/fc_exch.c:825 fc_seq_start_next+0x30/0x4b

This was due to trying to allocate a sequence in a request handler
when the exchange had been reset.

Delete the WARN_ON.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:06 -05:00
Joe Eykholt
e9ba8b4278 [SCSI] libfc: in fc_lport_destroy, flush rports after turning off link
During an fcoe module unload, we saw a problem where fc_rport_work()
finds the lport has been freed.  The rdata points to an area
containing 0x6b6b6b6b... the pool poison value from kmem_free().

In fcoe_if_destroy() we call fc_fabric_logoff() then fc_lport_destroy().
fc_fabric_logoff() flushes the remote port work, but we're still receiving
requests, and an RSCN or PLOGI arrives which creates more rports.

Note that although the LLD also checks link_up, it doesn't do it
under the lport mutex, so it can deliver frames to
fc_lport_recv_req() even after link_up is cleared.
So, re-check link_up there.

We need to flush the rports by calling disc_stop_final()
after we clear link_up.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:05 -05:00
Joe Eykholt
1190d92581 [SCSI] libfc: stop login after fabric logoff
When removing the fcoe module, several lports were being shut down
through fc_lport_fabric_logoff().

Occasionally, one would enter reset state before fc_lport_destroy()
was called, and since link_up was still true, it would log back in.

If we just clear link_up earlier, then we wouldn't be accepting LOGO
requests from other initiators while we are shutting down.

Fix by changing the LOGO response handler to enter DISABLED instead
of RESET.  Add an fc_lport_enter_disabled() function which does
what fc_lport_enter_reset() did, except it doesn't proceed to FLOGI state.

Move the code that was common between fc_lport_enter_reset() and
fc_lport_enter_disabled() into a new fc_lport_reset_locked() function.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:05 -05:00
Joe Eykholt
b1d9fd5574 [SCSI] libfc: rename lport NONE state to DISABLED
The state NONE was meant to be invalid, but has been used as
the initial state.  Rename it to be DISABLED, as more descriptive.
Further patches will make it the like the RESET state, except
it won't transition to FLOGI until fc_lport_fabric_login() is called.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:04 -05:00
Joe Eykholt
f161fb7210 [SCSI] fcoe: stop delivery of received frames before doing lport_destroy()
To be more sure that no more input arrives at the local port as
it is being destroyed, clean the queues in the per-cpu receive
threads.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:04 -05:00
Joe Eykholt
7f74549ff6 [SCSI] libfc: change debug messages to give host number.
libfc debug messages currently show 'lport: <fc-id>:'
wher <fc-id> is the hex assigned port-id.  When the lport
is logged off, that will be zero, so its hard to distinguish
which instance is involved.  The FC-ID can change
if the port is re-patched or changes VSANs.

Two lports may even have the same FC-ID if connected to isolated SANs.

Change the debug messages to print the SCSI host number "hostN:",
which will not change for the life of the lport.
Still show the FC_ID on lport messages.

Also, add a macro to FC_RPORT_ID_DBG for rport debugging where there's
no rdata structure involved.  It takes the lport and port_id as parameters.
Use this in fc_rport_recv_plogi_req() and fc_rport_recv_logo_req().

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:03 -05:00
Joe Eykholt
beb29a6d42 [SCSI] libfc: remove extra semicolons from debug macros
This is unlikely to cause any problems, but the libfc debug macros
introduce extra undesirable semicolons.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:03 -05:00
Yi Zou
2f718d64ec [SCSI] fcoe: Call dev_ethtool_get_settings() in fcoe_link_ok
No need to check phys_dev here, just call dev_ethtool_get_settings() directly
will take care of this.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:03 -05:00
Yi Zou
5a84baeaf7 [SCSI] libfcoe: Set fip_flags according to fcf and lport's capability of SPMA support
When encap the els for FIP, set the fip_flags according to the FCF and lport's
capability of supporting SPMA or FPMA or both.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:02 -05:00
Yi Zou
7a7f0c7f7a [SCSI] fcoe: Fix validation of mac address when checking for spma support
Fix this bug of validating the wrong mac address while checking for SAN MAC
address support from LLD as we should check ha->addr not ctlr.ctl_src_addr.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:02 -05:00
Mike Christie
3c0d1d94aa [SCSI] ALUA: send STPG if explicit and implicit is supported
alua_activate only sends a STPG if only explicit is suppored.
As a result, for EMC targets that support both we end up doing
a implicit failover when X commands are finally sent to
the other SP.

This patch does a AND on the h->tpgs, so we do a explicit failover
right away.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:01 -05:00
James Bottomley
a4a8b064dd [SCSI] scsi_transport_sas: fix incorrect duplicate setup of max_phys
There are two setup places for max_phys in scsi_transport_sas.c; one
incorrectly places a NULL into host_attrs instead of port_attrs.  Remove it.

Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:01 -05:00
James Smart
4643682ba5 [SCSI] fc_transport: Correct max fc_host attribute count
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:00 -05:00
James Smart
7cfbc8d966 [SCSI] lpfc 8.3.4: Update driver version to 8.3.4
Update driver version to 8.3.4

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:52:00 -05:00
James Smart
e4e74273c3 [SCSI] lpfc 8.3.4: Remove spaces before newlines in several log messages
Remove spaces before newlines in several log messages

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:59 -05:00
James Smart
f1c3b0fcbb [SCSI] lpfc 8.3.4: Add bsg (SGIOv4) support for ELS/CT support
Add bsg (SGIOv4) support for sending and receiving ELS, CT commands

This patch adds a new file, lpfc_bsg.c.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:59 -05:00
James Smart
1c6834a7e8 [SCSI] lpfc 8.3.4: NPIV vport fixes
NPIV vport fixes

- Fixed static vport creation on SLI4 HBAs
- Fixed vport create sending init_vpi before REG_VFI
- Fix unable to create vports on SLI4 HBA's Port2

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:58 -05:00
James Smart
32b9793fe6 [SCSI] lpfc 8.3.4: Fix a pair of FCoE issues
Fix a pair of FCoE issues

- Fix Region 23 FCoE Parameters not being read correctly
- Fix race condition when there are FCoE events during FCF table read

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:58 -05:00
James Smart
8568a4d249 [SCSI] lpfc 8.3.4: Various SLI3 fixes
Various SLI3 fixes

- Fix for firmware dump failure
- Fix inband remote management

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:57 -05:00
James Smart
a0c87cbdb5 [SCSI] lpfc 8.3.4: Consistently Implement persistent port disable
Consistently implement persistent port disable.

Ability was to be managed in the adapter via firmware via flash settings.
However, not all firmware images supported it. Uniformly support it
everywhere.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:57 -05:00
James Smart
8fa38513dd [SCSI] lpfc 8.3.4: Various SLI4 fixes
Various SLI4 fixes

- Fix switch name not used in the FCF record for FCoE HBAs
- Enabled HBA UE error polling error-condition action code
- Rewrite lpfc_sli4_scmd_to_wqidx_distr() to handle counter rollover cleanly
- Modify resume_rpi mailbox data structure to match current SLI4 spec
- Do not issue mailbox command in MBX_POLL mode when LPFC_HBA_ERROR is set
- Wait for HBA POST completion before checking Online and UE registers
- Fix accumulated total length not being filled in on unsolicited IOCBs
- Use PCI config space register to determine SLI rev of HBA
- Turn on starting ELS tmo function timer during device initialization

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:56 -05:00
Johannes Berg
66d6faec2f [SCSI] fcoe: convert to %pM
print_mac is being deprecated, and %pM makes for smaller
code anyway.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:56 -05:00
Jiri Slaby
e34ccdfe0e [SCSI] lpfc: don't dereference NULL
When kzalloc fails in lpfc_hba_alloc, don't dereference the NULL by
lpfc_printf_log. Use dev_err instead.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-By: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:55 -05:00
Dave Jones
0fd30f7769 [SCSI] qla2xxx: Fix __LITTLE_ENDIAN definition warnings
On ppc64, gcc 4.4 spews lots of..

drivers/scsi/qla2xxx/qla_def.h:1485:7: warning: "__LITTLE_ENDIAN" is not defined

Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:55 -05:00
Anil Veerabhadrappa
fac3cc458f [SCSI] bnx2i: register given device with cnic if shost != NULL in ep_connect()
When using iface, bnx2i was unable to offload further connections after all
active sessions are logged out. bnx2i will unregister the device from cnic
when the last connection is torn down. Next call to ep_connect() will fail
because the device is not registered. This issue is not seen if shost == NULL
is passed to ep_connect() call because in that case bnx2i will registers all
known devices with cnic before doing a route look-up.  When shost != NULL,
bnx2i knows the device on which to offload the connection and has to register
this device before attempting to offload the connection

Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:54 -05:00
Randy Dunlap
fe5d20c818 [SCSI] scsi_transport_fc: fix kernel-doc param name
Change function parameter name in kernel-doc to match the function's
actual parameter name, to fix 2 kernel-doc warnings.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:54 -05:00
Anil Veerabhadrappa
3be924fb1d [SCSI] bnx2i: convert bnx2i_dev_lock to mutex
convert bnx2i_dev_lock to type mutex from rwlock_t because
cnic->register_device() can sleep for various reasons including memory
allocation, waiting for ISCSI_INIT completion and while acquiring mutex lock,
cnic_lock.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:53 -05:00
Anil Veerabhadrappa
4e85f15166 [SCSI] bnx2i: bug fixes in bnx2i_init_one to handle error conditions
Fixed bnx2i_init_one() to properly handle return code of
cnic->register_device() and propagate it back to the caller.  No need to check
for BNX2I_CNIC_REGISTERED, because unless the adapter is added to adapter_list
it will not be registered in ep_connect context

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:52 -05:00
Anil Veerabhadrappa
1ed0f6a3ef [SCSI] bnx2i: remove global variable bnx2i_reg_devices
Removed bnx2i_reg_devices as this counter is not really
used in a meaningful way

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:51 -05:00
Martin K. Petersen
002b1eb2c0 [SCSI] Print failed commands
When a request fails we print the sense data but not the actual command
that failed.  Add a printout of the operation + CDB for failed commands.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:51 -05:00
Chandra Seetharaman
6c10db72c9 [SCSI] scsi_dh: Reference count scsi_dh_attach
Problem reported: http://marc.info/?l=dm-devel&m=124585978305866&w=2

scsi_dh does not do a refernce count for attach/detach, and this affects
the way it is supposed to work with multipath when a device is not
in the dev_list of the hardware handler.

This patch adds a reference count that counts each attach.

Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:51 -05:00
Douglas Gilbert
b4567ca630 [SCSI] update scsi/constants.c
It has been 3 years since this file was sync-ed with
www.t10.org . Information taken from the last bunch
of drafts released in May 2009. More asc/ascq codes
are coming for thin provisioning; when approved and
allocated another patch could add them prior to this
patch going live.

Changelog:
   - add some new command names and rename two commands
   - sync asc/ascq table with www.t10.org/lists/asc-num.txt
   - correct bug in scsi_extd_sense_format() [second
     for loop]

Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-22 17:51:50 -05:00
Linus Torvalds
3edf2fb9d8 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: check saved state before restore
2009-08-22 12:14:01 -07:00
Linus Torvalds
e3054ea7f7 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] mpt2sas: fix config request and diag reset deadlock
  [SCSI] mpt2sas: Bump driver version 01.100.04.00
  [SCSI] mpt2sas: fix oops because drv data points to NULL on resume from hibernate
  [SCSI] mpt2sas: fix crash due to Watchdog is active while OS in standby mode
  [SCSI] mpt2sas: fix infinite loop inside config request
  [SCSI] mpt2sas: Excessive log info causes sas iounit page time out
  [SCSI] mpt2sas: Raid 10 Value is showing as Raid 1E in /va/log/messages
  [SCSI] mpt2sas: Expander fix oops saying "Already part of another port"
  [SCSI] mpt2sas: Introduced check for enclosure_handle to avoid crash
2009-08-22 08:30:58 -07:00
Linus Torvalds
422bef879e Linux 2.6.31-rc7 2009-08-21 18:00:46 -07:00
Linus Torvalds
8e9d78edea Re-introduce page mapping check in mark_buffer_dirty()
In commit a8e7d49aa7 ("Fix race in
create_empty_buffers() vs __set_page_dirty_buffers()"), I removed a test
for a NULL page mapping unintentionally when some of the code inside
__set_page_dirty() was moved to the callers.

That removal generally didn't matter, since a filesystem would serialize
truncation (which clears the page mapping) against writing (which marks
the buffer dirty), so locking at a higher level (either per-page or an
inode at a time) should mean that the buffer page would be stable.  And
indeed, nothing bad seemed to happen.

Except it turns out that apparently reiserfs does something odd when
under load and writing out the journal, and we have a number of bugzilla
entries that look similar:

	http://bugzilla.kernel.org/show_bug.cgi?id=13556
	http://bugzilla.kernel.org/show_bug.cgi?id=13756
	http://bugzilla.kernel.org/show_bug.cgi?id=13876

and it looks like reiserfs depended on that check (the common theme
seems to be "data=journal", and a journal writeback during a truncate).

I suspect reiserfs should have some additional locking, but in the
meantime this should get us back to the pre-2.6.29 behavior.

Pattern-pointed-out-by: Roland Kletzing <devzero@web.de>
Cc: stable@kernel.org (2.6.29 and 2.6.30)
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-08-21 17:40:08 -07:00