The i2c_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Since 43cc71eed1, the platform
modalias is prefixed with "platform:".
Current code has the id_table, thus add MODULE_DEVICE_TABLE will
automatically setup the modalias.
Also make charger_manager_id static as it is only used in this driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
When reading flags, bq27x00_read() argument is inverted and causes
reads 2 of bytes for bq27200 and 1 byte for bq27500, while their register
sizes are 1 and 2 bytes respectively. This causes bq27500 upper flag
bits always to be returned as 0, causing full charge state to never be
reported correctly, so fix it.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This reverts commit 270968c098.
Grazvydas Ignotas wrote:
After 270968c098 "bq27x00_battery: Fix reporting status value for
bq27500 battery" status doesn't seem to be reported correctly when the
battery is close to fully charged state. It reports "Not charging"
while in fact there is >130mA current flowing to the battery according
to current_now.
This status report seems to be based on CHG bit in status register,
but looking at the datasheet the description says "(Fast) charging
allowed", which I guess means that the chip recommends charging and
not that charging is actually going on? If you check the bit while
battery is discharging and it's not full, the bit is also set.
Suggested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* git://git.infradead.org/battery-2.6: (68 commits)
power_supply: Mark da9052 driver as broken
power_supply: Drop usage of nowarn variant of sysfs_create_link()
s3c_adc_battery: Average over more than one adc sample
power_supply: Add DA9052 battery driver
isp1704_charger: Fix missing check
jz4740-battery: Fix signedness bug
power_supply: Assume mains power by default
sbs-battery: Fix devicetree match table
ARM: rx51: Add bq27200 i2c board info
sbs-battery: Change power supply name
devicetree-bindings: Propagate bq20z75->sbs rename to dt bindings
devicetree-bindings: Add vendor entry for Smart Battery Systems
sbs-battery: Rename internals to new name
bq20z75: Rename to sbs-battery
wm97xx_battery: Use DEFINE_MUTEX() for work_lock
max8997_charger: Remove duplicate module.h
lp8727_charger: Some minor fixes for the header
lp8727_charger: Add header file
power_supply: Convert drivers/power/* to use module_platform_driver()
power_supply: Add "unknown" in power supply type
...
There are some problems with MFD part of this driver, so the
driver fails to build:
drivers/power/da9052-battery.c: In function 'da9052_bat_read_volt':
drivers/power/da9052-battery.c:293:2: error: implicit declaration of function 'da9052_adc_manual_read' [-Werror=implicit-function-declaration]
drivers/power/da9052-battery.c: In function 'da9052_bat_check_presence':
drivers/power/da9052-battery.c:306:2: error: implicit declaration of function 'da9052_adc_read_temp' [-Werror=implicit-function-declaration]
drivers/power/da9052-battery.c: In function 'da9052_determine_vc_tbl_index':
drivers/power/da9052-battery.c:348:1: warning: control reaches end of non-void function [-Wreturn-type]
cc1: some warnings being treated as errors
The fix for MFD part will probably go post -rc1 (or in the next merge
window), so let's disable the driver for now.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The function is not exported to modules, plus we do want to catch anyone
who tries to create complex hierarchy (in that case we'd need to change
'powers' symlink to a directory, probably under a different name to not
break ABI).
This patch fixes the following build error:
ERROR: "sysfs_create_link_nowarn" [drivers/power/power_supply.ko] undefined!
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Some sources for adc battery information provide only inaccurate results
where the read value differs from the real value with positive and negative
offsets. For such sources it can be more accurate to collect two or more
value sample and use the average of all collected values.
This patch adds pdata options volt_samples, current_samples and
backup_volt_samples to specifiy the number of samples to collect,
reads the specified number of samples and calculates the average of those.
For unset sample-number-values a default of 1 is assumed.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Driver for DA9052 battery charger. This driver depends on DA9052 MFD core
dirver for definitions and methods.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
A segfault happens if there's no board information.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Heikki Krogerus <krohei@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
wait_for_completion_interruptible_timeout() may return negative value.
In this case, checking if (t > 0) will return true if t is unsigned.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
If no power class device is found in power_supply_is_system_supplied(),
the function currently returns 0, which basically means that the system
is supposed to be running on battery. In practice, mobile devices tend
to always implement at least one power class device and more often two
(battery and AC adapter). Systems with no registered power class
devices are more likely to be desktop systems, where the system is
always powered by mains.
So, change the default return value of
power_supply_is_system_supplied() from 0 (running on battery) to 1
(running on mains.)
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
It should be an of module table, not i2c.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The power supply name used to be fixed as "battery". This change allows
for multiple batteries by generating the name rather than using a fixed
value.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Now that this driver is named more generally, this change updates
the internal variables, defines and functions to use this new name.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This driver for the bq20z75 implemented the register spec defined
by the SBS standard. As this is not unique to this the TI part this
was originally written for, we can generalize this driver to
show its support for any SBS compliant battery.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
work_lock can be initialized automatically with
DEFINE_MUTEX() rather than explicitly calling mutex_init().
This patch also removes an unused bat_lock mutex.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
module.h was included twice.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch converts the drivers in drivers/power/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Nithish Mahalingam <nithish.mahalingam@intel.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Balaji Rao <balajirrao@openmoko.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Clifton Barnes <cabarnes@indesign-llc.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
For the default value of power supply type, "unknown" is added.
With default prop value, supply type property can be displayed
as default - "Unknown".
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
1. Useless braces were omitted
2. Useless void casts were omitted
3. module exit name changed
lp8727_chg_exit -> lp8727_exit
4. Pointer coding style changes
no space between pointer('*') and pointer name
ex) u8 * data -> u8 *data
5. Author information change : email and additional author
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
lp8727 i2c r/w functions are based on SMBUS I2C BLOCK. So the driver needs to
check whether i2c bus supports this functionality or not.
Signed-off-by: Woogyom Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
National Semiconductor LP8727 is the battery charger with Micro/Mini
USB interface. This IC includes below functions:
- I2C interface for accessing user registers
- Single input Li-Ion battery charger
- Charger input ID detection from Micro/Mini USB
- Multiplexing switches on USB, UART
Signed-off-by: Woogyom Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Charger Manager provides power-supply-class aggregating
information from multiple chargers and a fuel-gauge.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Because battery health monitoring should be done even when suspended,
it needs to wake up and suspend periodically. Thus, userspace battery
monitoring may incur too much overhead; every device and task is woken
up periodically. Charger Manager uses suspend-again to provide
in-suspend monitoring.
This patch allows to monitor battery health in-suspend state.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
If a power supply has a scope of "Device", then allow the power supply
to indicate what device it actually powers. This is represented in the
power supply's sysfs directory as a symlink named "powers", which points to
the sysfs directory of the powered device.
If the device has children, then the sub-devices are also powered by
the same power supply.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Richard Hughes <richard@hughsie.com>
This adds a "scope" attribute to a power_supply, which indicates how
much of the system it powers. It appears in sysfs as "scope" or in
the uevent file as POWER_SUPPLY_SCOPE=. There are presently three
possible values:
Unknown - unknown power topology
System - the power supply powers the whole system
Device - it powers a specific device, or tree of devices
A power supply which doesn't have a "scope" attribute should be assumed to
have "System" scope.
In general, usermode should assume that loss of all System-scoped power
supplies will power off the whole system, but any single one is sufficient
to power the system.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Richard Hughes <richard@hughsie.com>
When DCDC input line over current detecting, PMIC will change
charging current automatically. Logging event is enough.
Signed-off-by: Major Lee <major_lee@wistron.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
[fix build]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The interrupt for ac on/off can be missed during boot time.
Check if online by seeing if we have power. We choose 0.5V
since this is high enough to avoid random reading from a
input that could be floating if no charger.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Ted Bennett <tbennett@marvell.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Reading the voltage, charge etc requires that we tell the chip
what property we want to read before reading it according to
maxim.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Thomas Liu <Thomas.Liu@maxim-ic.com>
Tested-by: Ted Bennett <tbennett@marvell.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
In max17042_get_property(...), the values returned by
max17042_read_reg are directly assigned to the variables,
even if the read results in an error.
This patch checks for the return code from max17042_read_reg and
exits the function if there is any error.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Add rated capacity of the HP iPAQ hx4700 3.7V 3600mAh (359114-001)
battery. For this battery the value of the rated capacity EEPROM
register at 0x32 is 14; thus rated_capacities[14] = 3600.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts
disabled], We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler returns with
interrupts enabled (see commit [b738a50a: genirq: Warn when handler
enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
* power_supply_unregister call bq27x00_battery_get_property which
call bq27x00_battery_poll
* make sure that bq27x00_battery_poll will not call
schedule_delayed_work again after unregister (which cause OOPS)
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
* Do not be noise if battery is not calibrated (use dev_dbg)
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
* CI (Capacity Inaccurate) flag is set after full reset on bq27000 battery
* when is set, all capacity properties should be reported incorrectly,
because there was no learning cycle and battery was not calibrated
* instead reporting incorrect values, report -ENODATA
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
* This prevent reporting old current_now value for bq27000
* Also ask for current flags, to make sure that current_now
will be reported with correct signature
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The power core infrastructure allow external power change
events to be passed to drivers what are listed in the
supplied_to call back field. Enable this feature by
allowing the supplied_to field to be passed to the driver.
This feature will enable drivers named in the supplied_to
field that have a external_power_changed callback to be
notified when power was been turned on or off.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
On brownstone rev 4 ac-insert detect is handled by vbus.
allow the platform code to configure the disabling of insert
by setting no_insert_detect.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Brownstone does not have temperature reading circuit hooked up.
This leads to spurious interrupts.
Allow the platform layer to indicate no temperature circuit
and do not activate interrupts if no temperature control is set
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The datasheet indicates a 12 bit value is returned for i2c
registers for voltage and current. Code was assuming 8 bits.
But default for chip is 12 bit return value.
Voltage is returned in 2mV units -- adjust to return as uV
per linux power spec
Adjust current calculation to return units in uA.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The 'val' is a 'unsigned char', so it is never less than zero.
Signed-off-by: Jonghwan Choi <jhbird.choi@gmail.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Since 9d08d5d77a, irq_to_gpio() is no
longer available but still in use by collie_battery.c. As it's just
for a debug message, just get rid of this call.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
When DCDC input line over current detecting, PMIC will change charging
current automatically. Logging event is enough.
Signed-off-by: Major Lee <major_lee@wistron.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This change simplifies the implementation.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
As suggested by Igor Grinberg, this change make the implementation looks
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch fixes the following noise (by renaming _drv to _driver):
WARNING: drivers/power/olpc_battery.o(.data+0x100): Section mismatch in reference from the variable olpc_battery_drv to the function .devinit.text:olpc_battery_probe()
The variable olpc_battery_drv references
the function __devinit olpc_battery_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: drivers/power/olpc_battery.o(.data+0x104): Section mismatch in reference from the variable olpc_battery_drv to the function .devexit.text:olpc_battery_remove()
The variable olpc_battery_drv references
the function __devexit olpc_battery_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: drivers/power/olpc_battery.o(.data+0x128): Section mismatch in reference from the variable olpc_battery_drv to the variable .devinit.rodata:olpc_battery_ids
The variable olpc_battery_drv references
the variable __devinitconst olpc_battery_ids
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Adding support to generate platform data when kernel is configured
through device tree.
Also adding the binding for the TI bq20z75 fuel gadge and the
bq20z75 driver.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Says Andrew:
"60 patches. That's good enough for -rc1 I guess. I have quite a lot
of detritus to be rechecked, work through maintainers, etc.
- most of the remains of MM
- rtc
- various misc
- cgroups
- memcg
- cpusets
- procfs
- ipc
- rapidio
- sysctl
- pps
- w1
- drivers/misc
- aio"
* akpm: (60 commits)
memcg: replace ss->id_lock with a rwlock
aio: allocate kiocbs in batches
drivers/misc/vmw_balloon.c: fix typo in code comment
drivers/misc/vmw_balloon.c: determine page allocation flag can_sleep outside loop
w1: disable irqs in critical section
drivers/w1/w1_int.c: multiple masters used same init_name
drivers/power/ds2780_battery.c: fix deadlock upon insertion and removal
drivers/power/ds2780_battery.c: add a nolock function to w1 interface
drivers/power/ds2780_battery.c: create central point for calling w1 interface
w1: ds2760 and ds2780, use ida for id and ida_simple_get() to get it
pps gpio client: add missing dependency
pps: new client driver using GPIO
pps: default echo function
include/linux/dma-mapping.h: add dma_zalloc_coherent()
sysctl: make CONFIG_SYSCTL_SYSCALL default to n
sysctl: add support for poll()
RapidIO: documentation update
drivers/net/rionet.c: fix ethernet address macros for LE platforms
RapidIO: fix potential null deref in rio_setup_device()
RapidIO: add mport driver for Tsi721 bridge
...
The module.h header is no longer going to be implicitly present
everywhere. So real modular users need to call out its use
explicitly in advance.
[v2: add new users reported by Randy Dunlap <rdunlap@xenotime.net>]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
It was actually getting this before by a tangled mess of implict
includes that is going to be cleaned up. Fix it now, so we don't
get this after the cleanup.
power_supply_sysfs.c: In function ‘power_supply_attr_is_visible’:
power_supply_sysfs.c:184: error: ‘S_IRUSR’ undeclared (first use in this function)
power_supply_sysfs.c:184: error: (Each undeclared identifier is reported only once
power_supply_sysfs.c:184: error: for each function it appears in.)
power_supply_sysfs.c:184: error: ‘S_IRGRP’ undeclared (first use in this function)
power_supply_sysfs.c:184: error: ‘S_IROTH’ undeclared (first use in this function)
power_supply_sysfs.c:196: error: ‘S_IWUSR’ undeclared (first use in this function)
make[3]: *** [drivers/power/power_supply_sysfs.o] Error 1
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fix format warning:
drivers/power/power_supply_sysfs.c:82: warning: format '%d' expects type 'int', but argument 4 has type 'ssize_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
commit 9ad63986c6
"pda_power: Add support for using otg transceiver events"
introduces below build error if !CONFIG_USB_OTG_UTILS.
CC drivers/power/pda_power.o
drivers/power/pda_power.c: In function 'pda_power_probe':
drivers/power/pda_power.c:322: error: 'otg_is_usb_online' undeclared (first use in this function)
drivers/power/pda_power.c:322: error: (Each undeclared identifier is reported only once
drivers/power/pda_power.c:322: error: for each function it appears in.)
drivers/power/pda_power.c:325: error: 'otg_is_ac_online' undeclared (first use in this function)
drivers/power/pda_power.c:371: error: 'otg_handle_notification' undeclared (first use in this function)
make[2]: *** [drivers/power/pda_power.o] Error 1
make[1]: *** [drivers/power] Error 2
make: *** [drivers] Error 2
This patch adds #ifdef CONFIG_USB_OTG_UTILS guards at necessary places to fix
build errors.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The calculation had error in getting voltage values from
MAX17042 registers. The least bit denotes 78.125uV (625/8).
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
PROP_CURRENT_NOW value is first divided then multiplied up
causing a lose of accuracy. Use the same method as
PROP_CURRENT_AVG to do the calculation.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
On MMP2 brownstone divide by 0 error since probe sets r_sns
after calling power_supply_register.
Move the code up a few lines. r_sns comes from the platform
data.
PROP_CURRENT_AVG and PROP_CURRENT divide the result by r_sns.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Add a missing break for case 0 of pdata->timeout, otherwise it will fall
through to the default case and return error.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Battery and AC events can now be used to wake up the system from suspend.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This is cleaner, and allows suspend/resume (wakeup) handlers to be
added in an upcoming patch.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Don't tell the system about the battery charger if it's not enabled, we
can reasonably assume that if the charger is not enabled then no battery
will ever be connected so reporting state is at best going to waste time
and at worst going to cause confusing information in the UI.
For simplicity and robustness we continue to register and handle interrupts
from the charger.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
If the platform data sets the use_otg_notifier flag,
the driver will now register an otg notifier callback and listen
to transceiver events for AC/USB plug-in events instead. This would
normally be used by not specifying is_xx_online callbacks and
not specifying any irqs so the state machine is completely driven
from OTG xceiver events.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
According to the comments in include/linux/init.h:
"Pointers to __devexit functions must use __devexit_p(function_name), the
wrapper will insert either the function_name or NULL, depending on the config
options."
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Clifton Barnes <cabarnes@indesign-llc.com>
Cc: Peter Edwards <sweetlilmre@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Since 43cc71eed1 (platform: prefix MODALIAS
with "platform:"), the platform modalias is prefixed with "platform:".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The platform_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Add linux/module.h to fix this compilation error:
drivers/power/s3c_adc_battery.c:435:15: error: expected declaration specifiers or ‘...’ before string constant
drivers/power/s3c_adc_battery.c:435:1: warning: data definition has no type or storage class
drivers/power/s3c_adc_battery.c:435:1: warning: type defaults to ‘int’ in declaration of ‘MODULE_AUTHOR’
drivers/power/s3c_adc_battery.c:435:15: warning: function declaration isn’t a prototype
drivers/power/s3c_adc_battery.c:436:20: error: expected declaration specifiers or ‘...’ before string constant
drivers/power/s3c_adc_battery.c:436:1: warning: data definition has no type or storage class
drivers/power/s3c_adc_battery.c:436:1: warning: type defaults to ‘int’ in declaration of ‘MODULE_DESCRIPTION’
drivers/power/s3c_adc_battery.c:436:20: warning: function declaration isn’t a prototype
drivers/power/s3c_adc_battery.c:437:16: error: expected declaration specifiers or ‘...’ before string constant
drivers/power/s3c_adc_battery.c:437:1: warning: data definition has no type or storage class
drivers/power/s3c_adc_battery.c:437:1: warning: type defaults to ‘int’ in declaration of ‘MODULE_LICENSE’
drivers/power/s3c_adc_battery.c:437:16: warning: function declaration isn’t a prototype
make[2]: *** [drivers/power/s3c_adc_battery.o] Error 1
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ian Lartey <ian@opensource.wolfsonmicro.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
power/max8997_charger.c uses interfaces from linux/module.h,
so it should include that file. This fixes build errors.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
power/max8998_charger.c uses interfaces from linux/module.h,
so it should include that file. This fixes build errors.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
* git://git.infradead.org/battery-2.6:
gpio-charger: Fix checking return value of request_any_context_irq
power_supply: MAX17042: Support additional properties
max8903_charger: Allow platform data to be __initdata
power_supply: Add charger driver for MAX8998/LP3974
power_supply: Add charger driver for MAX8997/8966
max17042_battery: Remove obsolete cleanup for clientdata
twl4030_charger: Fix warnings
wm831x_power: Support multiple instances
wm831x_backup: Support multiple instances
apm_power: Fix style error in macros
s3c_adc_battery: Fix annotation for s3c_adc_battery_probe()
bq20z75: Enable detection after registering
bq20z75: Add support for external notification
request_any_context_irq() returns a negative value on failure.
On success, it returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch supports additional properties (PRESENT, CYCLE_COUNT,
VOLTAGE_MAX, VOLTAGE_MIN_DESIGN, CURRENT_NOW, CURRENT_AVG,
CHARGE_FULL, and TEMP).
Plus, initialization code for registers is added.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Platform files may have declared 8903 platform data as __initdata. This
patch removes the dependency on pdata pointer so that using __initdata
on pdata will not incur errors. Note that such error does not incur
SECTION MISMATCH warning in (at least some) compilers.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch supports power supply APIs for MAX8998/LP3974.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
MAX8997/8966 chip is a multi-function device which includes
PMIC, RTC, Fuel Gauge, MUIC, Haptic, Flash control, and
Battery charging control.
The driver for it is located at drivers/mfd.
This patch supports battery charging control of MAX8997/8966 chip and
provides power supply class information to userspace.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
A few new i2c-drivers came into the kernel which clear the
clientdata-pointer on exit or error. This is obsolete meanwhile,
the core will do it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Fix warnings emitted by some versions of gcc:
drivers/power/twl4030_charger.c:490: warning: overflow in implicit constant conversion
drivers/power/twl4030_charger.c:498: warning: overflow in implicit constant conversion
While at it, also fix module_param permissions and a typo in my name.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
If there are multiple wm831x devices in the system we need to assign
different names to the power supply devices in order to ensure we can
create the sysfs entries for them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
If there are multiple wm831x devices in the system we need to assign
different names to the power supply devices in order to ensure we can
create the sysfs entries for them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Two macros in the changed file contained complex expressions which
were not enclosed by parentheses.
Signed-off-by: Ken O'Brien <kernel@kenobrien.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
A probe() function is used at device init time rather than system init
time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Need to enable detection, which is also blocking the unit conversion logic
after registering the power_supply.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Adding support for external power change notification. One problem found
is that there is a lag time before the sensor will return a new status.
To ensure that we only fire off the power_supply_changed event when the
status returned from the sensor is actually different, we delay sending
the the notification, and instead poll on it looking for a change. The
amount of time to poll is configurable via platform data.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
I no longer work at Bluewater Systems. Update my email address accordingly. I
have deleted my email address from C files rather than change it. This
was suggested by several people, since the commit from my new email
address will cause scripts/get_maintainer.pl to function properly. I
have not added the .mailmap entry as suggested by Joe because I think
it is no longer necessary if I touch all the files which had my name
in them.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Cc: Andre Renaud <andre@bluewatersys.com>
Cc: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: trivial@kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.infradead.org/battery-2.6:
PXA: Use dev_pm_ops in z2_battery
ds2760_battery: Fix rated capacity of the hx4700 1800mAh battery
ds2760_battery: Fix indexing of the 4 active full EEPROM registers
power: Make test_power driver more dynamic.
bq27x00_battery: Name of cycle count property
max8903_charger: Add GENERIC_HARDIRQS as a dependency (fixes S390 build)
ARM: RX-51: Enable isp1704 power on/off
isp1704_charger: Allow board specific powering routine
gpio-charger: Add gpio_charger_resume
power_supply: Add driver for MAX8903 charger
Add support for the Maxim/Dallas DS2780 Stand-Alone Fuel Gauge IC.
It was suggested to combine this functionality with the current ds2782
driver. Unfortunately, I'm unable to commit the time to refactoring this
driver to that extent and I don't have a platform with the ds2782 part to
validate that there are no regression issues by adding this functionality.
[akpm@linux-foundation.org: use min_t()]
Signed-off-by: Clifton Barnes <cabarnes@indesign-llc.com>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid to get platform_data from parent device. Get it from mfd cell
device instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
