mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()
Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.
Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.
The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull the initial preempt_count value into a single
definition site.
Maintainers for: alpha, ia64 and m68k, please have a look,
your arch code is funny.
The header magic is a bit odd, but similar to the KERNEL_DS
one, CPP waits with expanding these macros until the
INIT_THREAD_INFO macro itself is expanded, which is in
arch/*/kernel/init_task.c where we've already included
sched.h so we're good.
Cc: tony.luck@intel.com
Cc: rth@twiddle.net
Cc: geert@linux-m68k.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault(). All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
avr32, mn10300, parisc, s390, sh, xtensa:
They never set PT_DTRACE, but clear it after do_execve().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Chris Zankel <chris@zankel.net>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* create mm/init-mm.c, move init_mm there
* remove INIT_MM, initialize init_mm with C99 initializer
* unexport init_mm on all arches:
init_mm is already unexported on x86.
One strange place is some OMAP driver (drivers/video/omap/) which
won't build modular, but it's already wants get_vm_area() export.
Somebody should look there.
[akpm@linux-foundation.org: add missing #includes]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Fix oops on unaligned user access
avr32: Add support for Mediama RMTx add-on board for ATNGW100
avr32: Change Atmel ATNGW100 config to add choice of add-on board
Fix MIMC200 board LCD init
avr32: Fix clash in ATMEL_USART_ flags
avr32: remove obsolete hw_interrupt_type
avr32: Solves problem with inverted MCI detect pin on Merisc board
atmel-mci: Add support for inverted detect pin
The unaligned address exception handler (and others) does not scan the
fixup tables before oopsing. This is bad because it means passing a
badly aligned pointer from user space might crash the kernel.
Fix this by scanning the fixup tables in _exception(). This should
resolve the issue for unaligned addresses as well as other less common
exceptions that might be happening during a userspace access. The page
fault handler already does fixup processing.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Everyone cut and paste this comment from my original one. We now do
it generically, so cut the comments.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Amerigo Wang <amwang@redhat.com>
The existing asm-generic/atomic.h only defines the
atomic_long type. This renames it to atomic-long.h
so we have a place to add a truly generic atomic.h
that can be used on all non-SMP systems.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
This provides a reliable way for asm-generic/types.h and other
files to find out if it is running on a 32 or 64 bit platform.
We cannot use CONFIG_64BIT for this in headers that are included
from user space because CONFIG symbols are not available there.
We also cannot do it inside of asm/types.h because some headers
need the word size but cannot include types.h.
The solution is to introduce a new header <asm/bitsperlong.h>
that defines both __BITS_PER_LONG for user space and
BITS_PER_LONG for usage in the kernel. The asm-generic
version falls back to 32 bit unless the architecture overrides
it, which I did for all 64 bit platforms.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The existing asm-generic versions are incomplete and included
by some architectures. New architectures should be able
to use a generic version, so rename the existing files and
change all users, which lets us add the new files.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch updates the LCD init code for the MIMC200 board.
V2 fixes a .yres typo and corrects an incorrect setup value
in the call to at32_add_device_lcdc()
Without this patch, the lcd setup is wrong and won't display images
correctly (if at all !!)
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
At the moment ATMEL_USART_{RTS,CTS,CLK} have the values
1, 2 and 3 respectively. Given these are used in bitmasks,
trying to turn on the CLK line will in fact turn on the
RTS and CTS lines as well.
Change the value of ATMEL_USART_CLK to 4.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Stephen Rothwell <sfr@canb.auug.org.au> writes:
> Today's linux-next build of at least some av32 and arm configs failed like this:
>
> arch/avr32/kernel/signal.c:216: error: conflicting types for 'restart_syscall'
> include/linux/sched.h:2184: error: previous definition of 'restart_syscall' was here
>
> Caused by commit 690cc3ffe3 ("syscall:
> Implement a convinience function restart_syscall") from the net tree.
Grrr. Some days it feels like all of the good names are already taken.
Let's just rename the two static users in arm and avr32 to get this
sorted out.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have
been kept around for migration reasons. After more than two years it's
time to remove them finally.
This patch cleans up one of the remaining users. When all such patches
hit mainline we can remove the defines and typedefs finally.
Impact: cleanup
Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Same patch as before, modified to use bool.
This patch solves the problem with the inverted mci detect pin on Merisc
boards.
Signed-off-by: Jonas Larsson <jonas.larsson@martinsson.se>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'avr32-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: add hardware handshake support to atmel_serial
avr32: add RTS/CTS/CLK pin selection for the USARTs
Add RTC support for Merisc boards
avr32: at32ap700x: setup DMA for AC97C in the machine code
avr32: at32ap700x: setup DMA for ABDAC in the machine code
Add Merisc board support
avr32: use gpio_is_valid() to check USBA vbus_pin I/O line
atmel-usba-udc: use gpio_is_valid() to check vbus_pin I/O line
avr32: fix timing LCD parameters for EVKLCD10X boards
avr32: use GPIO line PB15 on EVKLCD10x boards for backlight
avr32: configure MCI detect and write protect pins for EVKLCD10x boards
avr32: set pin mask to alternative 18 bpp for EVKLCD10x boards
avr32: add pin mask for 18-bit color on the LCD controller
avr32: fix 15-bit LCDC pin mask to use MSB lines
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (413 commits)
tracing, net: fix net tree and tracing tree merge interaction
tracing, powerpc: fix powerpc tree and tracing tree interaction
ring-buffer: do not remove reader page from list on ring buffer free
function-graph: allow unregistering twice
trace: make argument 'mem' of trace_seq_putmem() const
tracing: add missing 'extern' keywords to trace_output.h
tracing: provide trace_seq_reserve()
blktrace: print out BLK_TN_MESSAGE properly
blktrace: extract duplidate code
blktrace: fix memory leak when freeing struct blk_io_trace
blktrace: fix blk_probes_ref chaos
blktrace: make classic output more classic
blktrace: fix off-by-one bug
blktrace: fix the original blktrace
blktrace: fix a race when creating blk_tree_root in debugfs
blktrace: fix timestamp in binary output
tracing, Text Edit Lock: cleanup
tracing: filter fix for TRACE_EVENT_FORMAT events
ftrace: Using FTRACE_WARN_ON() to check "freed record" in ftrace_release()
x86: kretprobe-booster interrupt emulation code fix
...
Fix up trivial conflicts in
arch/parisc/include/asm/ftrace.h
include/linux/memory.h
kernel/extable.c
kernel/module.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
CONFIG_DEBUG_PAGEALLOC is now supported by x86, powerpc, sparc64, and
s390. This patch implements it for the rest of the architectures by
filling the pages with poison byte patterns after free_pages() and
verifying the poison patterns before alloc_pages().
This generic one cannot detect invalid page accesses immediately but
invalid read access may cause invalid dereference by poisoned memory and
invalid write access can be detected after a long delay.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds extra parameter to AT32 at32_map_usart(), so as to reserve
RTS/CTS/CLK pins.
All boards under arch/avr32/boards have been updated (trivial change), but
not all have been tested.
Signed-off-by: Peter Ma <pma@mediamatech.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds RTC support for the Merisc boards.
Signed-off-by: Jonas Larsson <jonas.larsson@martinsson.se>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch will adjust the setup the DMA controller for the AC97
Controller in the at32ap700x machine code. This setup matches the new
ALSA driver for the AC97C.
The struct ac97c_platform_data has been moved into its own header file
located in the sound include path.
Tested on ATSTK1006 + ATSTK1000.
This patch will setup the AC97 controller properly for the adjusted
machine code. Both EVKLCD10x and Hammerhead board has been updated.
Tested on EVKLCD10x, and copied to Hammerhead board.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
[haavard.skinnemoen@atmel.com: fold with board code update]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch will adjust the setup the DMA controller for the Audio
Bistream DAC in the at32ap700x machine code. This setup matches the new
ALSA driver for the ABDAC.
Tested on ATSTK1006 + ATSTK1000.
This patch will setup the needed platform data for the Audio Bistream
DAC used by the Favr-32 board.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
[haavard.skinnemoen@atmel.com: fold board code update]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Merisc is the family name for a range of AVR32-based boards.
The boards are designed to be used in a man-machine interfacing
environment, utilizing a touch-based graphical user interface. They host
a vast range of I/O peripherals as well as a large SDRAM & Flash memory
bank.
For more information see: http://www.martinsson.se/merisc
Signed-off-by: Jonas Larsson <jonas.larsson@martinsson.se>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (32 commits)
x86: disable __do_IRQ support
sparseirq, powerpc/cell: fix unused variable warning in interrupt.c
genirq: deprecate obsolete typedefs and defines
genirq: deprecate __do_IRQ
genirq: add doc to struct irqaction
genirq: use kzalloc instead of explicit zero initialization
genirq: make irqreturn_t an enum
genirq: remove redundant if condition
genirq: remove unused hw_irq_controller typedef
irq: export remove_irq() and setup_irq() symbols
irq: match remove_irq() args with setup_irq()
irq: add remove_irq() for freeing of setup_irq() irqs
genirq: assert that irq handlers are indeed running in hardirq context
irq: name 'p' variables a bit better
irq: further clean up the free_irq() code flow
irq: refactor and clean up the free_irq() code flow
irq: clean up manage.c
irq: use GFP_KERNEL for action allocation in request_irq()
kernel/irq: fix sparse warning: make symbol static
irq: optimize init_kstat_irqs/init_copy_kstat_irqs
...
This patch will use gpio_is_valid() to check the vbus_pin I/O line.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adjusts the timing parameters for the Kyocera LCD panels
connected on the EVKLCD10X addon boards.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The PB15 GPIO line is used to control the enable and disable signal for
the backlight regulator on EVKLCD10x boards. This patch hands the I/O
line over to the LCDC driver, which will control when to enable and
disable the backlight.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
[haavard.skinnemoen@atmel.com: reverted ac97c change]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch removes the special handling of MCI platform data for
EVKLCD10x boards. This is now possible since the pin mask for the LCD
controller is no longer reserving the I/O lines used for MCI card
detection and write protect.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch will set the pin mask to alternative 18 bits per pixel output
for EVKLCD10x boards.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds two defines for setting a pin mask for 18-bit LCD panels
connected to the LCD controller. One mask for primary output and one
mask for alternative output.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
