The generic sched_clock registration function was previously
done lockless, due to the fact that it was expected to be called
only once. However, now there are systems that may register
multiple sched_clock sources, for which the lack of locking has
casued problems:
If two sched_clock sources are registered we may end up in a
situation where a call to sched_clock() may be accessing the
epoch cycle count for the old counter and the cycle count for the
new counter. This can lead to confusing results where
sched_clock() values jump and then are reset to 0 (due to the way
the registration function forces the epoch_ns to be 0).
Fix this by reorganizing the registration function to hold the
seqlock for as short a time as possible while we update the
clock_data structure for a new counter. We also put any
accumulated time into epoch_ns instead of resetting the time to
0 so that the clock doesn't reset after each successful
registration.
[jstultz: Added extra context to the commit message]
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Josh Cartwright <joshc@codeaurora.org>
Link: http://lkml.kernel.org/r/1392662736-7803-2-git-send-email-john.stultz@linaro.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
AMD systems which use the C1E workaround in the amd_e400_idle routine
trigger the WARN_ON_ONCE in the broadcast code when onlining a CPU.
The reason is that the idle routine of those AMD systems switches the
cpu into forced broadcast mode early on before the newly brought up
CPU can switch over to high resolution / NOHZ mode. The timer related
CPU1 bringup looks like this:
clockevent_register_device(local_apic);
tick_setup(local_apic);
...
idle()
tick_broadcast_on_off(FORCE);
tick_broadcast_oneshot_control(ENTER)
cpumask_set(cpu, broadcast_oneshot_mask);
halt();
Now the broadcast interrupt on CPU0 sets CPU1 in the
broadcast_pending_mask and wakes CPU1. So CPU1 continues:
local_apic_timer_interrupt()
tick_handle_periodic();
softirq()
tick_init_highres();
cpumask_clr(cpu, broadcast_oneshot_mask);
tick_broadcast_oneshot_control(ENTER)
WARN_ON(cpumask_test(cpu, broadcast_pending_mask);
So while we remove CPU1 from the broadcast_oneshot_mask when we switch
over to highres mode, we do not clear the pending bit, which then
triggers the warning when we go back to idle.
The reason why this is only visible on C1E affected AMD systems is
that the other machines enter the deep sleep states via
acpi_idle/intel_idle and exit the broadcast mode before executing the
remote triggered local_apic_timer_interrupt. So the pending bit is
already cleared when the switch over to highres mode is clearing the
oneshot mask.
The solution is simple: Clear the pending bit together with the mask
bit when we switch over to highres mode.
Stanislaw came up independently with the same patch by enforcing the
C1E workaround and debugging the fallout. I picked mine, because mine
has a changelog :)
Reported-by: poma <pomidorabelisima@gmail.com>
Debugged-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Olaf Hering <olaf@aepfle.de>
Cc: Dave Jones <davej@redhat.com>
Cc: Justin M. Forbes <jforbes@redhat.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1402111434180.21991@ionos.tec.linutronix.de
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When compiling for the IA-64 ski emulator, HZ is set to 32 because the
emulation is slow and we don't want to waste too many cycles processing
timers. Alpha also has an option to set HZ to 32.
This causes integer underflow in
kernel/time/jiffies.c:
kernel/time/jiffies.c:66:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
.mult = NSEC_PER_JIFFY << JIFFIES_SHIFT, /* details above */
^
This patch reduces the JIFFIES_SHIFT value to avoid the overflow.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Link: http://lkml.kernel.org/r/alpine.LRH.2.02.1401241639100.23871@file01.intranet.prod.int.rdu2.redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull scheduler changes from Ingo Molnar:
- Add the initial implementation of SCHED_DEADLINE support: a real-time
scheduling policy where tasks that meet their deadlines and
periodically execute their instances in less than their runtime quota
see real-time scheduling and won't miss any of their deadlines.
Tasks that go over their quota get delayed (Available to privileged
users for now)
- Clean up and fix preempt_enable_no_resched() abuse all around the
tree
- Do sched_clock() performance optimizations on x86 and elsewhere
- Fix and improve auto-NUMA balancing
- Fix and clean up the idle loop
- Apply various cleanups and fixes
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
sched: Fix __sched_setscheduler() nice test
sched: Move SCHED_RESET_ON_FORK into attr::sched_flags
sched: Fix up attr::sched_priority warning
sched: Fix up scheduler syscall LTP fails
sched: Preserve the nice level over sched_setscheduler() and sched_setparam() calls
sched/core: Fix htmldocs warnings
sched/deadline: No need to check p if dl_se is valid
sched/deadline: Remove unused variables
sched/deadline: Fix sparse static warnings
m68k: Fix build warning in mac_via.h
sched, thermal: Clean up preempt_enable_no_resched() abuse
sched, net: Fixup busy_loop_us_clock()
sched, net: Clean up preempt_enable_no_resched() abuse
sched/preempt: Fix up missed PREEMPT_NEED_RESCHED folding
sched/preempt, locking: Rework local_bh_{dis,en}able()
sched/clock, x86: Avoid a runtime condition in native_sched_clock()
sched/clock: Fix up clear_sched_clock_stable()
sched/clock, x86: Use a static_key for sched_clock_stable
sched/clock: Remove local_irq_disable() from the clocks
sched/clock, x86: Rewrite cyc2ns() to avoid the need to disable IRQs
...
Code usually starts with 'tab' instead of 7 'space' in kernel
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Kevin Hilman <khilman@linaro.org>
Link: http://lkml.kernel.org/r/1386074112-30754-2-git-send-email-alex.shi@linaro.org
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
We don't need to fetch the timekeeping max deferment under the
jiffies_lock seqlock.
If the clocksource is updated concurrently while we stop the tick,
stop machine is called and the tick will be reevaluated again along with
uptodate jiffies and its related values.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Kevin Hilman <khilman@linaro.org>
Link: http://lkml.kernel.org/r/1387320692-28460-9-git-send-email-fweisbec@gmail.com
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
This makes the code more symetric against the existing tick functions
called on irq exit: tick_irq_exit() and tick_nohz_irq_exit().
These function are also symetric as they mirror each other's action:
we start to account idle time on irq exit and we stop this accounting
on irq entry. Also the tick is stopped on irq exit and timekeeping
catches up with the tickless time elapsed until we reach irq entry.
This rename was suggested by Peter Zijlstra a long while ago but it
got forgotten in the mass.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Kevin Hilman <khilman@linaro.org>
Link: http://lkml.kernel.org/r/1387320692-28460-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Unfortunately the seqlock lockdep enablement can't be used
in sched_clock(), since the lockdep infrastructure eventually
calls into sched_clock(), which causes a deadlock.
Thus, this patch changes all generic sched_clock() usage
to use the raw_* methods.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Reported-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1388704274-5278-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Prior to 92bb1fcf57 (Only
do nanosecond rounding on GENERIC_TIME_VSYSCALL_OLD
systems), the comment here was accuate, but now we can
mostly avoid the extra rounding which causes the unlikey
to be actually likely here.
So remove the out of date comment.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Fix trivial comment typo for tk_setup_internals().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Since 48cdc135d4 (Implement a shadow timekeeper), we have to
call timekeeping_update() after any adjustment to the timekeeping
structure in order to make sure that any adjustments to the structure
persist.
In the timekeeping suspend path, we udpate the timekeeper
structure, so we should be sure to update the shadow-timekeeper
before releasing the timekeeping locks. Currently this isn't done.
In most cases, the next time related code to run would be
timekeeping_resume, which does update the shadow-timekeeper, but
in an abundence of caution, this patch adds the call to
timekeeping_update() in the suspend path.
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable <stable@vger.kernel.org> #3.10+
Signed-off-by: John Stultz <john.stultz@linaro.org>
A think-o in the calculation of the monotonic -> tai time offset
results in CLOCK_TAI timers and nanosleeps to expire late (the
latency is ~2x the tai offset).
Fix this by adding the tai offset from the realtime offset instead
of subtracting.
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable <stable@vger.kernel.org> #3.10+
Signed-off-by: John Stultz <john.stultz@linaro.org>
Since the xtime lock was split into the timekeeping lock and
the jiffies lock, we no longer need to call update_wall_time()
while holding the jiffies lock.
Thus, this patch splits update_wall_time() out from do_timer().
This allows us to get away from calling clock_was_set_delayed()
in update_wall_time() and instead use the standard clock_was_set()
call that previously would deadlock, as it causes the jiffies lock
to be acquired.
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
As part of normal operaions, the hrtimer subsystem frequently calls
into the timekeeping code, creating a locking order of
hrtimer locks -> timekeeping locks
clock_was_set_delayed() was suppoed to allow us to avoid deadlocks
between the timekeeping the hrtimer subsystem, so that we could
notify the hrtimer subsytem the time had changed while holding
the timekeeping locks. This was done by scheduling delayed work
that would run later once we were out of the timekeeing code.
But unfortunately the lock chains are complex enoguh that in
scheduling delayed work, we end up eventually trying to grab
an hrtimer lock.
Sasha Levin noticed this in testing when the new seqlock lockdep
enablement triggered the following (somewhat abrieviated) message:
[ 251.100221] ======================================================
[ 251.100221] [ INFO: possible circular locking dependency detected ]
[ 251.100221] 3.13.0-rc2-next-20131206-sasha-00005-g8be2375-dirty #4053 Not tainted
[ 251.101967] -------------------------------------------------------
[ 251.101967] kworker/10:1/4506 is trying to acquire lock:
[ 251.101967] (timekeeper_seq){----..}, at: [<ffffffff81160e96>] retrigger_next_event+0x56/0x70
[ 251.101967]
[ 251.101967] but task is already holding lock:
[ 251.101967] (hrtimer_bases.lock#11){-.-...}, at: [<ffffffff81160e7c>] retrigger_next_event+0x3c/0x70
[ 251.101967]
[ 251.101967] which lock already depends on the new lock.
[ 251.101967]
[ 251.101967]
[ 251.101967] the existing dependency chain (in reverse order) is:
[ 251.101967]
-> #5 (hrtimer_bases.lock#11){-.-...}:
[snipped]
-> #4 (&rt_b->rt_runtime_lock){-.-...}:
[snipped]
-> #3 (&rq->lock){-.-.-.}:
[snipped]
-> #2 (&p->pi_lock){-.-.-.}:
[snipped]
-> #1 (&(&pool->lock)->rlock){-.-...}:
[ 251.101967] [<ffffffff81194803>] validate_chain+0x6c3/0x7b0
[ 251.101967] [<ffffffff81194d9d>] __lock_acquire+0x4ad/0x580
[ 251.101967] [<ffffffff81194ff2>] lock_acquire+0x182/0x1d0
[ 251.101967] [<ffffffff84398500>] _raw_spin_lock+0x40/0x80
[ 251.101967] [<ffffffff81153e69>] __queue_work+0x1a9/0x3f0
[ 251.101967] [<ffffffff81154168>] queue_work_on+0x98/0x120
[ 251.101967] [<ffffffff81161351>] clock_was_set_delayed+0x21/0x30
[ 251.101967] [<ffffffff811c4bd1>] do_adjtimex+0x111/0x160
[ 251.101967] [<ffffffff811e2711>] compat_sys_adjtimex+0x41/0x70
[ 251.101967] [<ffffffff843a4b49>] ia32_sysret+0x0/0x5
[ 251.101967]
-> #0 (timekeeper_seq){----..}:
[snipped]
[ 251.101967] other info that might help us debug this:
[ 251.101967]
[ 251.101967] Chain exists of:
timekeeper_seq --> &rt_b->rt_runtime_lock --> hrtimer_bases.lock#11
[ 251.101967] Possible unsafe locking scenario:
[ 251.101967]
[ 251.101967] CPU0 CPU1
[ 251.101967] ---- ----
[ 251.101967] lock(hrtimer_bases.lock#11);
[ 251.101967] lock(&rt_b->rt_runtime_lock);
[ 251.101967] lock(hrtimer_bases.lock#11);
[ 251.101967] lock(timekeeper_seq);
[ 251.101967]
[ 251.101967] *** DEADLOCK ***
[ 251.101967]
[ 251.101967] 3 locks held by kworker/10:1/4506:
[ 251.101967] #0: (events){.+.+.+}, at: [<ffffffff81154960>] process_one_work+0x200/0x530
[ 251.101967] #1: (hrtimer_work){+.+...}, at: [<ffffffff81154960>] process_one_work+0x200/0x530
[ 251.101967] #2: (hrtimer_bases.lock#11){-.-...}, at: [<ffffffff81160e7c>] retrigger_next_event+0x3c/0x70
[ 251.101967]
[ 251.101967] stack backtrace:
[ 251.101967] CPU: 10 PID: 4506 Comm: kworker/10:1 Not tainted 3.13.0-rc2-next-20131206-sasha-00005-g8be2375-dirty #4053
[ 251.101967] Workqueue: events clock_was_set_work
So the best solution is to avoid calling clock_was_set_delayed() while
holding the timekeeping lock, and instead using a flag variable to
decide if we should call clock_was_set() once we've released the locks.
This works for the case here, where the do_adjtimex() was the deadlock
trigger point. Unfortuantely, in update_wall_time() we still hold
the jiffies lock, which would deadlock with the ipi triggered by
clock_was_set(), preventing us from calling it even after we drop the
timekeeping lock. So instead call clock_was_set_delayed() at that point.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: stable <stable@vger.kernel.org> #3.10+
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In 780427f0e1 (Indicate that clock was set in the pvclock
gtod notifier), logic was added to pass a CLOCK_WAS_SET
notification to the pvclock notifier chain.
While that patch added a action flag returned from
accumulate_nsecs_to_secs(), it only uses the returned value
in one location, and not in the logarithmic accumulation.
This means if a leap second triggered during the logarithmic
accumulation (which is most likely where it would happen),
the notification that the clock was set would not make it to
the pv notifiers.
This patch extends the logarithmic_accumulation pass down
that action flag so proper notification will occur.
This patch also changes the varialbe action -> clock_set
per Ingo's suggestion.
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: <xen-devel@lists.xen.org>
Cc: stable <stable@vger.kernel.org> #3.11+
Signed-off-by: John Stultz <john.stultz@linaro.org>
Since 48cdc135d4 (Implement a shadow timekeeper), we have to
call timekeeping_update() after any adjustment to the timekeeping
structure in order to make sure that any adjustments to the structure
persist.
Unfortunately, the updates to the tai offset via adjtimex do not
trigger this update, causing adjustments to the tai offset to be
made and then over-written by the previous value at the next
update_wall_time() call.
This patch resovles the issue by calling timekeeping_update()
right after setting the tai offset.
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable <stable@vger.kernel.org> #3.10+
Signed-off-by: John Stultz <john.stultz@linaro.org>
A few functions use remote per CPU access APIs when they
deal with local values.
Just do the right conversion to improve performance, code
readability and debug checks.
While at it, lets extend some of these function names with *_this_cpu()
suffix in order to display their purpose more clearly.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
If CONFIG_NO_HZ=n tick_nohz_get_sleep_length() returns NSEC_PER_SEC/HZ.
If CONFIG_NO_HZ=y and the nohz functionality is disabled via the
command line option "nohz=off" or not enabled due to missing hardware
support, then tick_nohz_get_sleep_length() returns 0. That happens
because ts->sleep_length is never set in that case.
Set it to NSEC_PER_SEC/HZ when the NOHZ mode is inactive.
Reported-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since commit 1e75fa8be9 (time: Condense timekeeper.xtime
into xtime_sec - merged in v3.6), there has been an problem
with the error accounting in the timekeeping code, such that
when truncating to nanoseconds, we round up to the next nsec,
but the balancing adjustment to the ntp_error value was dropped.
This causes 1ns per tick drift forward of the clock.
In 3.7, this logic was isolated to only GENERIC_TIME_VSYSCALL_OLD
architectures (s390, ia64, powerpc).
The fix is simply to balance the accounting and to subtract the
added nanosecond from ntp_error. This allows the internal long-term
clock steering to keep the clock accurate.
While this fix removes the regression added in 1e75fa8be9, the
ideal solution is to move away from GENERIC_TIME_VSYSCALL_OLD
and use the new VSYSCALL method, which avoids entirely the
nanosecond granular rounding, and the resulting short-term clock
adjustment oscillation needed to keep long term accurate time.
[ jstultz: Many thanks to Martin for his efforts identifying this
subtle bug, and providing the fix. ]
Originally-from: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Paul Turner <pjt@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable <stable@vger.kernel.org> #v3.6+
Link: http://lkml.kernel.org/r/1385149491-20307-1-git-send-email-john.stultz@linaro.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
RCU and the fine grained idle time accounting functions check
tick_nohz_enabled. But that variable is merily telling that NOHZ has
been enabled in the config and not been disabled on the command line.
But it does not tell anything about nohz being active. That's what all
this should check for.
Matthew reported, that the idle accounting on his old P1 machine
showed bogus values, when he enabled NOHZ in the config and did not
disable it on the kernel command line. The reason is that his machine
uses (refined) jiffies as a clocksource which explains why the "fine"
grained accounting went into lala land, because it depends on when the
system goes and leaves idle relative to the jiffies increment.
Provide a tick_nohz_active indicator and let RCU and the accounting
code use this instead of tick_nohz_enable.
Reported-and-tested-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: john.stultz@linaro.org
Cc: mwhitehe@redhat.com
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1311132052240.30673@ionos.tec.linutronix.de
Pull timer changes from Ingo Molnar:
"Main changes in this cycle were:
- Updated full dynticks support.
- Event stream support for architected (ARM) timers.
- ARM clocksource driver updates.
- Move arm64 to using the generic sched_clock framework & resulting
cleanup in the generic sched_clock code.
- Misc fixes and cleanups"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
x86/time: Honor ACPI FADT flag indicating absence of a CMOS RTC
clocksource: sun4i: remove IRQF_DISABLED
clocksource: sun4i: Report the minimum tick that we can program
clocksource: sun4i: Select CLKSRC_MMIO
clocksource: Provide timekeeping for efm32 SoCs
clocksource: em_sti: convert to clk_prepare/unprepare
time: Fix signedness bug in sysfs_get_uname() and its callers
timekeeping: Fix some trivial typos in comments
alarmtimer: return EINVAL instead of ENOTSUPP if rtcdev doesn't exist
clocksource: arch_timer: Do not register arch_sys_counter twice
timer stats: Add a 'Collection: active/inactive' line to timer usage statistics
sched_clock: Remove sched_clock_func() hook
arch_timer: Move to generic sched_clock framework
clocksource: tcb_clksrc: Remove IRQF_DISABLED
clocksource: tcb_clksrc: Improve driver robustness
clocksource: tcb_clksrc: Replace clk_enable/disable with clk_prepare_enable/disable_unprepare
clocksource: arm_arch_timer: Use clocksource for suspend timekeeping
clocksource: dw_apb_timer_of: Mark a few more functions as __init
clocksource: Put nodes passed to CLOCKSOURCE_OF_DECLARE callbacks centrally
arm: zynq: Enable arm_global_timer
...
Marc Kleine-Budde pointed out, that commit 77cc982 "clocksource: use
clockevents_config_and_register() where possible" caused a regression
for some of the converted subarchs.
The reason is, that the clockevents core code converts the minimal
hardware tick delta to a nanosecond value for core internal
usage. This conversion is affected by integer math rounding loss, so
the backwards conversion to hardware ticks will likely result in a
value which is less than the configured hardware limitation. The
affected subarchs used their own workaround (SIGH!) which got lost in
the conversion.
The solution for the issue at hand is simple: adding evt->mult - 1 to
the shifted value before the integer divison in the core conversion
function takes care of it. But this only works for the case where for
the scaled math mult/shift pair "mult <= 1 << shift" is true. For the
case where "mult > 1 << shift" we can apply the rounding add only for
the minimum delta value to make sure that the backward conversion is
not less than the given hardware limit. For the upper bound we need to
omit the rounding add, because the backwards conversion is always
larger than the original latch value. That would violate the upper
bound of the hardware device.
Though looking closer at the details of that function reveals another
bogosity: The upper bounds check is broken as well. Checking for a
resulting "clc" value greater than KTIME_MAX after the conversion is
pointless. The conversion does:
u64 clc = (latch << evt->shift) / evt->mult;
So there is no sanity check for (latch << evt->shift) exceeding the
64bit boundary. The latch argument is "unsigned long", so on a 64bit
arch the handed in argument could easily lead to an unnoticed shift
overflow. With the above rounding fix applied the calculation before
the divison is:
u64 clc = (latch << evt->shift) + evt->mult - 1;
So we need to make sure, that neither the shift nor the rounding add
is overflowing the u64 boundary.
[ukl: move assignment to rnd after eventually changing mult, fix build
issue and correct comment with the right math]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: nicolas.ferre@atmel.com
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: john.stultz@linaro.org
Cc: kernel@pengutronix.de
Cc: Ronald Wahl <ronald.wahl@raritan.com>
Cc: LAK <linux-arm-kernel@lists.infradead.org>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1380052223-24139-1-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
sysfs_get_uname() is erroneously declared as returning size_t even
though it may return a negative value, specifically -EINVAL. Its
callers then check whether its return value is less than zero and indeed
that is never the case for size_t.
This patch changes sysfs_get_uname() to return ssize_t and makes sure
its callers use ssize_t accordingly.
Signed-off-by: Patrick Palka <patrick@parcs.ath.cx>
[jstultz: Didn't apply cleanly, as a similar partial fix was also applied
so had to resolve the collisions]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Fedora Ruby maintainer reported latest Ruby doesn't work on Fedora Rawhide
on ARM. (http://bugs.ruby-lang.org/issues/9008)
Because of, commit 1c6b39ad3f (alarmtimers: Return -ENOTSUPP if no
RTC device is present) intruduced to return ENOTSUPP when
clock_get{time,res} can't find a RTC device. However this is incorrect.
First, ENOTSUPP isn't exported to userland (ENOTSUP or EOPNOTSUP are the
closest userland equivlents).
Second, Posix and Linux man pages agree that clock_gettime and
clock_getres should return EINVAL if clk_id argument is invalid.
While the arugment that the clockid is valid, but just not supported
on this hardware could be made, this is just a technicality that
doesn't help userspace applicaitons, and only complicates error
handling.
Thus, this patch changes the code to use EINVAL.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: stable <stable@vger.kernel.org> #3.0 and up
Reported-by: Vit Ondruch <v.ondruch@tiscali.cz>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
[jstultz: Tweaks to commit message to include full rational]
Signed-off-by: John Stultz <john.stultz@linaro.org>
We can enable/disable timer statistics collection via:
echo [1|0] > /proc/timers_stats
and it would be nice if apps had the ability to check
what the current collection status is.
This patch adds a 'Collection: active/inactive' line to display the
current timer collection status.
Also bump up the timer stats version to v0.3.
Signed-off-by: Dong Zhu <bluezhudong@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/20131010075618.GH2139@zhudong.nay.redhat.com
[ Improved the changelog and the code. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull more timekeeping items for v3.13 from John Stultz:
* Small cleanup in the clocksource code.
* Fix for rtc-pl031 to let it work with alarmtimers.
* Move arm64 to using the generic sched_clock framework & resulting
cleanup in the generic sched_clock code.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Nobody is using sched_clock_func() anymore now that sched_clock
supports up to 64 bits. Remove the hook so that new code only
uses sched_clock_register().
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Pull (mostly) ARM clocksource driver updates from Daniel Lezcano:
" - Soren Brinkmann added FEAT_PERCPU to a clock device when it is local
per cpu. This feature prevents the clock framework to choose a per cpu
timer as a broadcast timer. This problem arised when the ARM global
timer is used when switching to the broadcast timer which is the case
now on Xillinx with its cpuidle driver.
- Stephen Boyd extended the generic sched_clock code to support 64bit
counters and removes the setup_sched_clock deprecation, as that causes
lots of warnings since there's still users in the arch/arm tree. He
added also the CLOCK_SOURCE_SUSPEND_NONSTOP flag on the architected
timer as they continue counting during suspend.
- Uwe Kleine-König added some missing __init sections and consolidated the
code by moving the of_node_put call from the drivers to the function
clocksource_of_init. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge updated full dynticks support from Frederic Weisbecker:
- support 32-bit systems (full dynticks was 64-bit only before)
- support ARM
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSSKOHAAoJEHm+PkMAQRiGeREH/3EqHmJPBzmVoJwR9/ykDoLg
u+TJTkuxZG220WhgXS7W/0ECyBX0U7yA0bY9PZbqgcdiLjY0veR18/pOhEq5RzHq
ub8Q+AJdiORF/sq268q7gnNmy3rSCgnrAyHA/bzBtkbisYODwZPYvWQVUjgNZ2dW
qtW/TE9rjANcUrk8WdOu9oWcwsq4cyG3cscbfHE/JLFy/8tB5GoD158gxKLZsLXk
uTCeUHMmvFRT56fZwfyvNstA8ozxXcHBmuu6+Ttceky2zeGzp6dOrd+d2SU1Ps3O
P91x4e/Af4RFEwDczGP6TpSBEf/J/JaqrM1drjhnQHho0hrNRZVUXhADFVADCXY=
=dOjB
-----END PGP SIGNATURE-----
Merge tag 'v3.12-rc3' into timers/core
Merge Linux 3.12-rc3 - refresh the tree with the latest fixes before merging new bits.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On most ARM systems the per-cpu clockevents are truly per-cpu in
the sense that they can't be controlled on any other CPU besides
the CPU that they interrupt. If one of these clockevents were to
become a broadcast source we will run into a lot of trouble
because the broadcast source is enabled on the first CPU to go
into deep idle (if that CPU suffers from FEAT_C3_STOP) and that
could be a different CPU than what the clockevent is interrupting
(or even worse the CPU that the clockevent interrupts could be
offline).
Theoretically it's possible to support per-cpu clockevents as the
broadcast source but so far we haven't needed this and supporting
it is rather complicated. Let's just deny the possibility for now
until this becomes a reality (let's hope it never does!).
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
The CONFIG_64BIT requirement on vtime can finally be removed
since we now depend on HAVE_VIRT_CPU_ACCOUNTING_GEN which
already takes care of the arch ability to handle nsecs based
cputime_t safely.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Arm Linux <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
With VIRT_CPU_ACCOUNTING_GEN, cputime_t becomes 64-bit. In order
to use that feature, arch code should be audited to ensure there are no
races in concurrent read/write of cputime_t. For example,
reading/writing 64-bit cputime_t on some 32-bit arches may require
multiple accesses for low and high value parts, so proper locking
is needed to protect against concurrent accesses.
Therefore, add CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN which arches can
enable after they've been audited for potential races.
This option is automatically enabled on 64-bit platforms.
Feature requested by Frederic Weisbecker.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Arm Linux <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Pull timer fix from Ingo Molnar:
"An NTP related lockup fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Fix HRTICK related deadlock from ntp lock changes
sysfs_override_clocksource(): The expression 'if (ret >= 0)' is always true.
This will cause clocksource_select() to always run.
Thus modified ret to be of type ssize_t.
sysfs_unbind_clocksource(): The expression 'if (ret < 0)' is always false.
So in case sysfs_get_uname() failed, the expression won't take an effect.
Thus modified ret to be of type ssize_t.
Signed-off-by: Elad Wexler <elad.wexler@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Gerlando Falauto reported that when HRTICK is enabled, it is
possible to trigger system deadlocks. These were hard to
reproduce, as HRTICK has been broken in the past, but seemed
to be connected to the timekeeping_seq lock.
Since seqlock/seqcount's aren't supported w/ lockdep, I added
some extra spinlock based locking and triggered the following
lockdep output:
[ 15.849182] ntpd/4062 is trying to acquire lock:
[ 15.849765] (&(&pool->lock)->rlock){..-...}, at: [<ffffffff810aa9b5>] __queue_work+0x145/0x480
[ 15.850051]
[ 15.850051] but task is already holding lock:
[ 15.850051] (timekeeper_lock){-.-.-.}, at: [<ffffffff810df6df>] do_adjtimex+0x7f/0x100
<snip>
[ 15.850051] Chain exists of: &(&pool->lock)->rlock --> &p->pi_lock --> timekeeper_lock
[ 15.850051] Possible unsafe locking scenario:
[ 15.850051]
[ 15.850051] CPU0 CPU1
[ 15.850051] ---- ----
[ 15.850051] lock(timekeeper_lock);
[ 15.850051] lock(&p->pi_lock);
[ 15.850051] lock(timekeeper_lock);
[ 15.850051] lock(&(&pool->lock)->rlock);
[ 15.850051]
[ 15.850051] *** DEADLOCK ***
The deadlock was introduced by 06c017fdd4 ("timekeeping:
Hold timekeepering locks in do_adjtimex and hardpps") in 3.10
This patch avoids this deadlock, by moving the call to
schedule_delayed_work() outside of the timekeeper lock
critical section.
Reported-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Tested-by: Lin Ming <minggr@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: stable <stable@vger.kernel.org> #3.11, 3.10
Link: http://lkml.kernel.org/r/1378943457-27314-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull timers/nohz changes from Ingo Molnar:
"It mostly contains fixes and full dynticks off-case optimizations, by
Frederic Weisbecker"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
nohz: Include local CPU in full dynticks global kick
nohz: Optimize full dynticks's sched hooks with static keys
nohz: Optimize full dynticks state checks with static keys
nohz: Rename a few state variables
vtime: Always debug check snapshot source _before_ updating it
vtime: Always scale generic vtime accounting results
vtime: Optimize full dynticks accounting off case with static keys
vtime: Describe overriden functions in dedicated arch headers
m68k: hardirq_count() only need preempt_mask.h
hardirq: Split preempt count mask definitions
context_tracking: Split low level state headers
vtime: Fix racy cputime delta update
vtime: Remove a few unneeded generic vtime state checks
context_tracking: User/kernel broundary cross trace events
context_tracking: Optimize context switch off case with static keys
context_tracking: Optimize guest APIs off case with static key
context_tracking: Optimize main APIs off case with static key
context_tracking: Ground setup for static key use
context_tracking: Remove full dynticks' hacky dependency on wide context tracking
nohz: Only enable context tracking on full dynticks CPUs
...
Pull RCU updates from Paul E. McKenney:
"
* Update RCU documentation. These were posted to LKML at
https://lkml.org/lkml/2013/8/19/611.
* Miscellaneous fixes. These were posted to LKML at
https://lkml.org/lkml/2013/8/19/619.
* Full-system idle detection. This is for use by Frederic
Weisbecker's adaptive-ticks mechanism. Its purpose is
to allow the timekeeping CPU to shut off its tick when
all other CPUs are idle. These were posted to LKML at
https://lkml.org/lkml/2013/8/19/648.
* Improve rcutorture test coverage. These were posted to LKML at
https://lkml.org/lkml/2013/8/19/675.
"
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This commit adds the state machine that takes the per-CPU idle data
as input and produces a full-system-idle indication as output. This
state machine is driven out of RCU's quiescent-state-forcing
mechanism, which invokes rcu_sysidle_check_cpu() to collect per-CPU
idle state and then rcu_sysidle_report() to drive the state machine.
The full-system-idle state is sampled using rcu_sys_is_idle(), which
also drives the state machine if RCU is idle (and does so by forcing
RCU to become non-idle). This function returns true if all but the
timekeeping CPU (tick_do_timer_cpu) are idle and have been idle long
enough to avoid memory contention on the full_sysidle_state state
variable. The rcu_sysidle_force_exit() may be called externally
to reset the state machine back into non-idle state.
For large systems the state machine is driven out of RCU's
force-quiescent-state logic, which provides good scalability at the price
of millisecond-scale latencies on the transition to full-system-idle
state. This is not so good for battery-powered systems, which are usually
small enough that they don't need to care about scalability, but which
do care deeply about energy efficiency. Small systems therefore drive
the state machine directly out of the idle-entry code. The number of
CPUs in a "small" system is defined by a new NO_HZ_FULL_SYSIDLE_SMALL
Kconfig parameter, which defaults to 8. Note that this is a build-time
definition.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
[ paulmck: Use true and false for boolean constants per Lai Jiangshan. ]
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
[ paulmck: Simplify logic and provide better comments for memory barriers,
based on review comments and questions by Lai Jiangshan. ]
Correct an issue with /proc/timer_list reported by Holger.
When reading from the proc file with a sufficiently small buffer, 2k so
not really that small, there was one could get hung trying to read the
file a chunk at a time.
The timer_list_start function failed to account for the possibility that
the offset was adjusted outside the timer_list_next.
Signed-off-by: Nathan Zimmer <nzimmer@sgi.com>
Reported-by: Holger Hans Peter Freyther <holger@freyther.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Berke Durak <berke.durak@xiphos.com>
Cc: Jeff Layton <jlayton@redhat.com>
Tested-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org> # 3.10.x
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current code requires that the scheduled update of the RTC happens
in the closest tick to the half of the second. This seems to be
difficult to achieve reliably. The scheduled work may be missing the
target time by a tick or two and be constantly rescheduled every second.
Relax the limit to 10 ticks. As a typical RTC drifts in the 11-minute
update interval by several milliseconds, this shouldn't affect the
overall accuracy of the RTC much.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
