This patch adds an 'if CAN_DEV...endif' Block around the CAN driver
symbols in drivers/net/can/Kconfig. So the 'depends on CAN' dependencies
can be removed.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-can@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a MODULE_ALIAS for the platform bindings and a
MODULE_DEVICE_TABLE for of bindings, so that the module can be loaded
automatically by udev.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch marks the bittiming_const pointer as in the struct can_pric as
"const". This allows us to mark the struct can_bittiming_const in the CAN
drivers as "const", too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make cc770_interrupt static to fix the following sparse warning:
drivers/net/can/cc770/cc770.c:699:13: warning: symbol
'cc770_interrupt' was not declared. Should it be static?
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Using | with a constant is always true.
Likely this should have be &.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
drivers/net/can/cc770/cc770.c included 'linux/can/dev.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This fix avoids a deadlock if an interrupt occurs
during consecutive port operations on ISA cards
utilising indirect access via address and data
port.
Tested on a B&R ISA card.
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wolfgang Zarre <lkdev@essax.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On slow systems and high CAN bitrates, the error message
"can_put_echo_skb: BUG! echo_skb is occupied!" did show up because
can_put_echo_skb() was called after starting the transfer.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This driver works with both, static platform data and device tree
bindings. It has been tested on a TQM855L board with two AN82527
CAN controllers on the local bus.
CC: Devicetree-discuss@lists.ozlabs.org
CC: linuxppc-dev@ozlabs.org
CC: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for legacy Bosch CC770 and Intel AN82527 CAN
controllers on the ISA or PC-104 bus. The I/O port or memory address
and the IRQ number must be specified via module parameters:
insmod cc770_isa.ko port=0x310,0x380 irq=7,11
for ISA devices using I/O ports or:
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11
for memory mapped ISA devices.
Indirect access via address and data port is supported as well:
insmod cc770_isa.ko port=0x310,0x380 indirect=1 irq=7,11
Furthermore, the following mode parameter can be defined:
clk: External oscillator clock frequency (default=16000000 [16 MHz])
cir: CPU interface register (default=0x40 [DSC])
bcr: Bus configuration register (default=0x40 [CBY])
cor: Clockout register (default=0x00)
Note: for clk, cir, bcr and cor, the first argument re-defines the
default for all other devices, e.g.:
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000
is equivalent to
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000,24000000
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for legacy Bosch CC770 and Intel AN82527 CAN
controllers on the ISA or PC-104 bus. The I/O port or memory address
and the IRQ number must be specified via module parameters:
insmod cc770_isa.ko port=0x310,0x380 irq=7,11
for ISA devices using I/O ports or:
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11
for memory mapped ISA devices.
Indirect access via address and data port is supported as well:
insmod cc770_isa.ko port=0x310,0x380 indirect=1 irq=7,11
Furthermore, the following mode parameter can be defined:
clk: External oscillator clock frequency (default=16000000 [16 MHz])
cir: CPU interface register (default=0x40 [CPU_DSC])
ocr, Bus configuration register (default=0x00)
cor, Clockout register (default=0x00)
Note: for clk, cir, bcr and cor, the first argument re-defines the
default for all other devices, e.g.:
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000
is equivalent to
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000,24000000
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
