This patch is in succession of previous patch
commit c842114792
xHCI: Adding #define values used for hub descriptor
Hub descriptors characteristics #defines values are added in
hub_configure() in place of magic numbers as asked by Alan Stern.
And the indentation for switch and case is changed to be same.
Some #defines values are added in ch11.h for defining hub class
protocols and used in hub.c and hcd.c in which magic values were
used for hub class protocols.
Signed-off-by: Aman Deep <amandeep3986@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xhci-hub used some numerical values for initialisation of root hub
descriptors. #define values are addded in usb 2.0 hub specification
file and these values are used for root hub characteristics
initialisation.
Also use some #defines in places where magic numbers are being used.
Signed-off-by: Aman Deep <amandeep3986@gmail.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for multiple read urbs to generic read implementation.
Use a static array of two read urbs for now which is enough to get a
50% throughput increase in one test setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove no longer used write_urb_busy field from struct usb_serial_port.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The HCD_FLAG_SAW_IRQ flag was introduced in order to catch IRQ routing
errors: If an URB was unlinked and the host controller hadn't gotten
any IRQs, it seemed likely that the IRQs were directed to the wrong
vector.
This warning hasn't come up in many years, as far as I know; interrupt
routing now seems to be well under control. Therefore there's no
reason to keep the flag around any more. This patch (as1495) finally
removes it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (348 commits)
[media] pctv452e: Remove bogus code
[media] adv7175: Make use of media bus pixel codes
[media] media: vb2: fix incorrect return value
[media] em28xx: implement VIDIOC_ENUM_FRAMESIZES
[media] cx23885: Stop the risc video fifo before reconfiguring it
[media] cx23885: Avoid incorrect error handling and reporting
[media] cx23885: Avoid stopping the risc engine during buffer timeout
[media] cx23885: Removed a spurious function cx23885_set_scale()
[media] cx23885: v4l2 api compliance, set the audioset field correctly
[media] cx23885: hook the audio selection functions into the main driver
[media] cx23885: add generic functions for dealing with audio input selection
[media] cx23885: fixes related to maximum number of inputs and range checking
[media] cx23885: Initial support for the MPX-885 mini-card
[media] cx25840: Ensure AUDIO6 and AUDIO7 trigger line-in baseband use
[media] cx23885: Enable audio line in support from the back panel
[media] cx23885: Allow the audio mux config to be specified on a per input basis
[media] cx25840: Enable support for non-tuner LR1/LR2 audio inputs
[media] cx23885: Name an internal i2c part and declare a bitfield by name
[media] cx23885: Ensure VBI buffers timeout quickly - bugfix for vbi hangs during streaming
[media] cx23885: remove channel dump diagnostics when a vbi buffer times out
...
Fix up trivial conflicts in drivers/misc/altera-stapl/altera.c (header
file rename vs add)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
some renesas_usbhs device is supporting OTG external device interface.
In that device, it is necessary to control PWEN/EXTLP on DVSTCTR.
This patch support it.
But renesas_usbhs driver doesn't have OTG support for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch add DVSTCTR control function for HOST support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs will have register DVSTCTR control function for HOST support.
This patch changes usbhsc_bus_ctrl() to usbsc_set_buswait(),
to remove DVSTCTR access from it,
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
SH7757 has a USB function with internal DMA controller (SUDMAC).
This patch supports the SUDMAC. The SUDMAC is incompatible with
general-purpose DMAC. So, it doesn't use dmaengine.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Kirkwood gave an unaligned memory access error on
line 742 of drivers/usb/host/echi-hcd.c:
"ehci->last_periodic_enable = ktime_get_real();"
Signed-off-by: Harro Haan <hrhaan@gmail.com>
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the device pass the USB2 software LPM and the host supports hardware
LPM, enable hardware LPM for the device to let the host decide when to
put the link into lower power state.
If hardware LPM is enabled for a port and driver wants to put it into
suspend, it must first disable hardware LPM, resume the port into U0,
and then suspend the port.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The uvcvideo extension unit API requires constants defined in the
video.h header. Add it to the list of includes exported to userspace.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In a few places in the kernel, the code prints
a human-readable USB device speed (eg. "high speed").
This involves a switch statement sometimes wrapped
around in ({ ... }) block leading to code repetition.
To mitigate this issue, this commit introduces
usb_speed_string() function, which returns
a human-readable name of provided speed.
It also changes a few places switch was used to use
this new function. This changes a bit the way the
speed is printed in few instances at the same time
standardising it.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The endpoint usage field is described in the USB 2.0 specification,
chapter 9.6.6.
Also, move the sync type fields block down by some lines to reflect the
fact that these are also stuffed in bmAttributes.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
not to confuse with Table 9-7 in USB 2.0 spec
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
M66592 has the pin of WR0 and WR1. So, if one write-pin of CPU
connects to the pins, we have to change the setting of FIFOSEL
register in the controller. If we don't change the setting,
the controller cannot send the data of odd length.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
R8A66597 has the pin of WR0 and WR1. So, if one write-pin of CPU
connects to the pins, we have to change the setting of FIFOSEL
register in the controller. If we don't change the setting,
the controller cannot send the data of odd length.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BUSWAIT is a 4-bit-wide value that controls the number of access waits
from the CPU to on-chip USB module. b'0000 inserts 0 wait (2 access
cycles) and b'1111 inserts 15 waits (17 access cycles, hardware
initial value), respectively.
BUSWAIT value depends on peripheral clock frequency supplied to on-chip
of each CPU, hence should be configurable through platform data.
Note that this patch assumes that b'0000 (0 wait, 2 access cycles) is
rerely used and considered as invalid. If valid 'buswait' data is not
provided by platform, initial b'1111 (15 waits, 17 access cycles) will
be applied as a safe default.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
udc_start() should only trigger the internal state machine and make
minimal house keeping. Before that call udc-core calls the bind()
callback and after the callback the pullup().
udc_stop() is simillar, udc-core calls pullup(), unbind() and finally
udc_stop().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When #include'd alone, <linux/usb/gadget.h>
causes a lot of compilation errors and warnings
-- all because it relies on the including code to
bring in the necessary #include's instead of
doing this itself.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SuperSpeed USB has defined a new descriptor, called
the Binary Device Object Store (BOS) Descriptor. It
has also changed a bit the definition of SET_FEATURE
and GET_STATUS requests to add USB3-specific details.
This patch implements both changes to the Composite
Gadget Framework.
[ balbi@ti.com : slight changes to commit log
fixed a compile error on ARM ]
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This field is used by the Gadget drivers to specify
the maximum speed they support, meaning: the maximum
speed they can provide descriptors for.
The driver speed will be set in consideration of this
value.
[ balbi@ti.com : dropped the ifdeffery ]
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch defines necessary fields to support
streaming for USB3.0.
It implements a new function, called
usb_ep_autoconfig_ss(), to be used instead of the
existing usb_ep_autoconfig() when working in
SuperSpeed mode and there is a need to search for
an endpoint according to the number of required
streams.
[ balbi@ti.com : slight changes to commit log ]
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add config_ep_by_speed() to configure the endpoint
according to the gadget speed.
Using this function will spare the FDs from handling
the endpoint chosen descriptor.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change usb_ep_enable() prototype to use endpoint
descriptor from usb_ep.
This optimization spares the FDs from saving the
endpoint chosen descriptor. This optimization is
not full though. To fully exploit this change, one
needs to update all the UDCs as well since in the
current implementation each of them saves the
endpoint descriptor in it's internal (and extended)
endpoint structure.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this class will be used to abstract away several of the duplicated
operations scattered among the USB gadget controller drivers.
Later, we can add an atomic notifier to tell interested drivers about
what's happening with the controller. Notifications such as suspend,
resume, enumerated, etc. will be useful, at a minimum, for implementing
usb charger detection.
As part of the converting process usb_gadget_probe_driver() is no longer
part of each udc but pushed into the ->stap() callback. The same for his
couterpart.
The core is currently set explicit to 'n'. It will be changed to 'y' once
all users are converted since it provides functions which clash with
other drivers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB DMA was installed on "normal DMAC" when SH7724 or older SuperH,
but the "USB-DMAC" was prepared on recent SuperH.
These 2 DMAC have a little bit different behavior.
This patch add DMAEngine code for "normal DMAC",
but it is still using PIO fifo.
The DMA fifo will be formally supported in the future.
You can enable DMA fifo by local fixup
usbhs_fifo_pio_push_handler -> usbhs_fifo_dma_push_handler
usbhs_fifo_pio_pop_handler -> usbhs_fifo_dma_pop_handler
on usbhsg_ep_enable.
This DMAEngine was tested by g_file_storage on SH7724 Ecovec board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
USB: UHCI: Support big endian GRUSBHC HC
sparc: add {read,write}*_be routines
USB: UHCI: Add support for big endian descriptors
USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
USB: UHCI: Add support for big endian mmio
usb-storage: Correct adjust_quirks to include latest flags
usb/isp1760: Fix possible unlink problems
usb/isp1760: Move function isp1760_endpoint_disable() within file.
USB: remove remaining usages of hcd->state from usbcore and fix regression
usb: musb: ux500: add configuration and build options for ux500 dma
usb: musb: ux500: add dma glue layer for ux500
usb: musb: ux500: add dma name for ux500
usb: musb: ux500: add ux500 specific code for gadget side
usb: musb: fix compile error
usb-storage: fix up the unusual_realtek device list
USB: gadget: f_audio: Fix invalid dereference of initdata
EHCI: don't rescan interrupt QHs needlessly
OHCI: fix regression caused by nVidia shutdown workaround
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
...
Some USB function drivers (e.g. f_mass_storage.c) need to delay or defer the
data/status stages of standard control requests like SET_CONFIGURATION or
SET_INTERFACE till they are done with their bookkeeping and are actually ready
for accepting new commands to their interface.
They can now achieve this functionality by returning USB_GADGET_DELAYED_STATUS
in their setup handlers (e.g. set_alt()). The composite framework will then
defer completion of the control transfer by not completing the data/status stages.
This ensures that the host does not send new packets to the interface till the
function driver is ready to take them.
When the function driver that requested for USB_GADGET_DELAYED_STATUS is done
with its bookkeeping, it should signal the composite framework to continue with
the data/status stages of the control transfer. It can do so by invoking
the new API usb_composite_setup_continue(). This is where the control transfer's
data/status stages are completed and host can initiate new transfers.
The DELAYED_STATUS mechanism is currently only supported if the expected data phase
is 0 bytes (i.e. w_length == 0). Since SET_CONFIGURATION and SET_INTERFACE are the
only cases that will use this mechanism, this is not a limitation.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement good battery algorithm defined in the battery charging V1.2 spec
for detecting different charging ports. USB hardware is put into low power
mode when connected to a dedicated charging port. vbus_draw and set_power
methods are implemented for determining the allowed current from Host in
different states (un-configured/suspend/configured).
The charger block is implemented using vendor specific registers and the
PHY used in MSM8960(28nm PHY) different from older targets like MSM8x60
and MSM7x30(45nm PHY). The PHY vendor and product id registers are not
implemented in the above chipsets. Hence PHY type is passed via platform
data.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
HSUSB core clock is derived from daytona fabric clock and for
HSUSB operational require minimum core clock at 55MHz. Since, HSUSB
cannot tolerate daytona fabric clock change in the middle of HSUSB
operational, vote for maximum Daytona fabric clock
while usb is operational
Signed-off-by: Anji jonnala <anjir@codeaurora.org>
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 3dacdf11 "usb: factor out state_string() on otg drivers"
broke building musb drivers since there is already another
otg_state_string() function in musb drivers, but with different
prototype. Fix musb drivers to use common otg_state_string(), too.
Also provide a nop for otg_state_string() if CONFIG_USB_OTG_UTILS
is not defined.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The two first HC capability registers (CAPLENGTH and HCIVERSION)
are defined as one 8-bit and one 16-bit register. Most HC
implementations have selected to treat these registers as part
of a 32-bit register, giving the same layout for both big and
small endian systems.
This patch adds a new quirk, big_endian_capbase, to support
controllers with big endian register interfaces that treat
HCIVERSION and CAPLENGTH as individual registers.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As pointed out by Arnd Bergmann, in include/linux/usb/ehci_def.h, struct
ehci_caps is defined with __attribute__((packed)) for no good reason,
and this triggers undefined behaviour when using ARM's readl() on
pointers to elements of this structure:
http://lkml.kernel.org/r/201102021700.20683.arnd@arndb.de
The same problem exists with the other two structures in ehci_def.h too,
so remove the __attribute__((packed)) from all of them.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-next' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
xhci 1.0: Set transfer burst last packet count field.
xhci 1.0: Set transfer burst count field.
xhci 1.0: Update TD size field format.
xhci 1.0: Only interrupt on short packet for IN EPs.
xhci: Remove sparse warning about cmd_status.
usbcore: warm reset USB3 port in SS.Inactive state
usbcore: Refine USB3.0 device suspend and resume
xHCI: report USB3.0 portstatus comply with USB3.0 specification
xHCI: Set link state support
xHCI: Clear link state change support
xHCI: warm reset support
usb/ch9: use proper endianess for wBytesPerInterval
xhci: Remove recursive call to xhci_handle_event
xhci: Add an assertion to check for virt_dev=0 bug.
xhci: Add rmb() between reading event validity & event data access.
xhci: Make xHCI driver endian-safe
while going through Tatyana's changes for the gadget framework I noticed
that this type is not defined as __le16.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Provide common otg_state_string() and use
it in drivers.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This delay is used to overjump debounce.
And, this patch also move usbhsc_drvcllbck_notify_hotplug to global,
because it will be called from other files.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The callback function which is called from platform must be removed
if module removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resubmit interrupt URB if device is open. Use a flag set in
usbnet_open() to determine this state. Also kill and free
interrupt URB in usbnet_disconnect().
[Rebased off git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git]
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
USB tethering does not work anymore since 2.6.39-rc2, but it's okay in
-rc1. The root cause is the new added mask code 'FLAG_POINTTOPOINT'
overlaps 'FLAG_MULTI_PACKET' in include/linux/usb/usbnet.h, this
causes logic issue in rx_process(). This patch cleans up the overlap.
Reported-and-Tested-by: Gottfried Haider <gottfried.haider@gmail.com>
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 41 occurrences of this type of Section mismatch warning
in g_mass_storage, g_serial, g_cdc, g_multi, g_nokia, g_ether, g_ffs:
(the 75 number reported earlier contained some duplicates.)
WARNING: drivers/usb/gadget/g_mass_storage.o(.text+0x687a): Section mismatch in reference from the function fsg_bind() to the function .devinit.text:usb_ep_autoconfig()
The function fsg_bind() references
the function __devinit usb_ep_autoconfig().
This is often because fsg_bind lacks a __devinit
annotation or the annotation of usb_ep_autoconfig is wrong.
Also remove __devinit from usb_ep_autoconfig_reset() to prevent
possible section mismatch problems with it.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Renesas SuperH has USBHS IP which can switch Host / Function.
This driver is designed so that Host / Function may dynamically change.
This patch add usb/renesas_usbhs and common code for SuperH USBHS.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some RNDIS devices don't respond on the control channel until polled
on the status channel. In particular, this was reported to be the
case for the 2Wire HomePortal 1000SW and for some Windows Mobile
devices.
This is roughly based on a patch by John Carr <john.carr@unrouted.co.uk>
which is currently applied by Mandriva.
Reported-by: Mark Glassberg <vzeeaxwl@myfairpoint.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation for the USB ethernet devices suggests that
only some devices are supposed to use usb0 as the network interface
name instead of eth0. The logic used there, and documented in
Kconfig for CDC is that eth0 will be used when the mac address
is a globally assigned one, but usb0 is used for the locally
managed range that is typically used on point-to-point links.
Unfortunately, this has caused a lot of pain on the smsc95xx
device that is used on the popular pandaboard without an
EEPROM to store the MAC address, which causes the driver to
call random_ether_address().
Obviously, there should be a proper MAC addressed assigned to
the device, and discussions are ongoing about how to solve
this, but this patch at least makes sure that the default
interface naming gets a little saner and matches what the
user can expect based on the documentation, including for
new devices.
The approach taken here is to flag whether a device might be a
point-to-point link with the new FLAG_POINTTOPOINT setting in
the usbnet driver_info. A driver can set both FLAG_POINTTOPOINT
and FLAG_ETHER if it is not sure (e.g. cdc_ether), or just one
of the two. The usbnet framework only looks at the MAC address
for device naming if both flags are set, otherwise it trusts the
flag.
Signed-off-by: Arnd Bergmann <arnd.bergmann@linaro.org>
Tested-by: Andy Green <andy.green@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a driver for the CDC Ethernet part of this modem. The
device's ID is blacklisted in cdc_ether.c and is white-listed in
this new driver because of the quirks needed to make it useful.
The modem's firmware exposes a CDC ACM port for modem control and a
CDC Ethernet port for network data. The descriptors look fine but
both ports actually are some sort of multiplexers requiring non-
standard headers added/removed from every packet or they get
ignored. All information is based on a usb traffic log from a
Windows machine.
On the Verizon 4G network I've seen speeds up to 1.1MB/s so far with
this driver, a speed-o-meter site reports 16.2Mbps/10.5Mbps.
Userspace scripts are required to talk to the CDC ACM port.
Signed-off-by: Andrzej Zaborowski <balrogg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (76 commits)
pch_uart: reference clock on CM-iTC
pch_phub: add new device ML7213
n_gsm: fix UIH control byte : P bit should be 0
n_gsm: add a documentation
serial: msm_serial_hs: Add MSM high speed UART driver
tty_audit: fix tty_audit_add_data live lock on audit disabled
tty: move cd1865.h to drivers/staging/tty/
Staging: tty: fix build with epca.c driver
pcmcia: synclink_cs: fix prototype for mgslpc_ioctl()
Staging: generic_serial: fix double locking bug
nozomi: don't use flush_scheduled_work()
tty/serial: Relax the device_type restriction from of_serial
MAINTAINERS: Update HVC file patterns
tty: phase out of ioctl file pointer for tty3270 as well
tty: forgot to remove ipwireless from drivers/char/pcmcia/Makefile
pch_uart: Fix DMA channel miss-setting issue.
pch_uart: fix exclusive access issue
pch_uart: fix auto flow control miss-setting issue
pch_uart: fix uart clock setting issue
pch_uart : Use dev_xxx not pr_xxx
...
Fix up trivial conflicts in drivers/misc/pch_phub.c (same patch applied
twice, then changes to the same area in one branch)
Use the Mult and bMaxBurst values from the endpoint companion
descriptor to calculate the max length of an isoc transfer.
Add USB_SS_MULT macro to access Mult field of bmAttributes, at
Sarah's suggestion.
This patch should be queued for the 2.6.36 and 2.6.37 stable trees, since
those were the first kernels to have isochronous support for SuperSpeed
devices.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
USB_PORT_STAT_SUPER_SPEED is a made up symbol that the USB core used to
track whether USB ports had a SuperSpeed device attached. This is a
linux-internal symbol that was used when SuperSpeed and non-SuperSpeed
devices would show up under the same xHCI roothub. This particular
port status is never returned by external USB 3.0 hubs. (Instead they
have a USB_PORT_STAT_SPEED_5GBPS that uses a completely different speed
mask.)
Now that the xHCI driver registers two roothubs, USB 3.0 devices will only
show up under USB 3.0 hubs. Rip out USB_PORT_STAT_SUPER_SPEED and replace
it with calls to hub_is_superspeed().
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Introduce the notion of a PCI device that may be associated with more than
one USB host controller driver (struct usb_hcd). This patch is the start
of the work to separate the xHCI host controller into two roothubs: a USB
3.0 roothub with SuperSpeed-only ports, and a USB 2.0 roothub with
HS/FS/LS ports.
One usb_hcd structure is designated to be the "primary HCD", and a pointer
is added to the usb_hcd structure to keep track of that. A new function
call, usb_hcd_is_primary_hcd() is added to check whether the USB hcd is
marked as the primary HCD (or if it is not part of a roothub pair). To
allow the USB core and xHCI driver to access either roothub in a pair, a
"shared_hcd" pointer is added to the usb_hcd structure.
Add a new function, usb_create_shared_hcd(), that does roothub allocation
for paired roothubs. It will act just like usb_create_hcd() did if the
primary_hcd pointer argument is NULL. If it is passed a non-NULL
primary_hcd pointer, it sets usb_hcd->shared_hcd and usb_hcd->primary_hcd
fields. It will also skip the bandwidth_mutex allocation, and set the
secondary hcd's bandwidth_mutex pointer to the primary HCD's mutex.
IRQs are only allocated once for the primary roothub.
Introduce a new usb_hcd driver flag that indicates the host controller
driver wants to create two roothubs. If the HCD_SHARED flag is set, then
the USB core PCI probe methods will allocate a second roothub, and make
sure that second roothub gets freed during rmmod and in initialization
error paths.
When usb_hc_died() is called with the primary HCD, make sure that any
roothubs that share that host controller are also marked as being dead.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The xHCI driver essentially has both a USB 2.0 and a USB 3.0 roothub. So
setting the HCD_USB3 bits in the hcd->driver->flags is a bit misleading.
Add a new field to usb_hcd, bcdUSB. Store the result of
hcd->driver->flags & HCD_MASK in it. Later, when we have the xHCI driver
register the two roothubs, we'll set the usb_hcd->bcdUSB field to HCD_USB2
for the USB 2.0 roothub, and HCD_USB3 for the USB 3.0 roothub.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Change the bandwith_mutex in struct usb_hcd to a pointer. This will allow
the pointer to be shared across usb_hcds for the upcoming work to split
the xHCI driver roothub into a USB 2.0/1.1 and a USB 3.0 bus.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Update the USB core to deal with USB 3.0 hubs. These hubs have a slightly
different hub descriptor than USB 2.0 hubs, with a fixed (rather than
variable length) size. Change the USB core's hub descriptor to have a
union for the last fields that differ. Change the host controller drivers
that access those last fields (DeviceRemovable and PortPowerCtrlMask) to
use the union.
Translate the new version of the hub port status field into the old
version that khubd understands. (Note: we need to fix it to translate the
roothub's port status once we stop converting it to USB 2.0 hub status
internally.)
Add new code to handle link state change status. Send out new control
messages that are needed for USB 3.0 hubs, like Set Hub Depth.
This patch is a modified version of the original patch submitted by John
Youn. It's updated to reflect the removal of the "bitmap" #define, and
change the hub descriptor accesses of a couple new host controller
drivers.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Using a #define to redefine a common variable name is a bad thing,
especially when the #define is in a header. include/linux/usb/hcd.h
redefined bitmap to DeviceRemovable to avoid typing a long field in the
hub descriptor. This has unintended side effects for files like
drivers/usb/core/devio.c that include that file, since another header
included after hcd.h has different variables named bitmap.
Remove the bitmap #define and replace instances of it in the host
controller code. Cleanup the spaces around function calls and square
brackets while we're at it.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
The Tegra 2 SoC has 3 EHCI compatible USB controllers. This patch adds
the necessary glue to allow the ehci-hcd driver to work on Tegra 2
SoCs.
The platform data is used to configure board-specific phy settings and
to configure the operating mode, as one of the ports may be used as a otg
port. For additional power saving, the driver supports powering down the
phy on bus suspend when it is used, for example, to connect an internal
device that use an out-of-band remote wakeup mechanism (e.g. a gpio).
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is used across all MSM SoCs. Hence give a generic name.
All Functions and strutures are also using "msm_otg" as prefix.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hcd->state variable is a disaster. It's not clearly owned by
either usbcore or the host controller drivers, and they both change it
from time to time, potentially stepping on each other's toes. It's
not protected by any locks. And there's no mechanism to prevent it
from going through an invalid transition.
This patch (as1451) takes a first step toward fixing these problems.
As it turns out, usbcore uses hcd->state for essentially only two
things: checking whether the controller's root hub is running and
checking whether the controller has died. Therefore the patch adds
two new atomic bitflags to the hcd structure, to store these pieces of
information. The new flags are used only by usbcore, and a private
spinlock prevents invalid combinations (a dead controller's root hub
cannot be running).
The patch does not change the places where usbcore sets hcd->state,
since HCDs may depend on them. Furthermore, there is one place in
usb_hcd_irq() where usbcore still must use hcd->state: An HCD's
interrupt handler can implicitly indicate that the controller died by
setting hcd->state to HC_STATE_HALT. Nevertheless, the new code is a
big improvement over the current code.
The patch makes one other change. The hcd_bus_suspend() and
hcd_bus_resume() routines now check first whether the host controller
has died; if it has then they return immediately without calling the
HCD's bus_suspend or bus_resume methods.
This fixes the major problem reported in Bugzilla #29902: The system
fails to suspend after a host controller dies during system resume.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alex Terekhov <a.terekhov@gmail.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Macro arguments used in expressions need to be enclosed in parenthesis
to avoid unpleasant surprises.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a driver doesn't know how much data a device is going to send,
the buffer size should be at least as big as the endpoint's maxpacket
value. The serial drivers don't follow this rule; many of them
request only 256-byte bulk-in buffers. As a result, they suffer
overflow errors if a high-speed device wants to send a lot of data,
because high-speed bulk endpoints are required to have a maxpacket
size of 512.
This patch (as1450) fixes the problem by using the driver's
bulk_in_size value as a minimum, always allocating buffers no smaller
than the endpoint's maxpacket size.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Flynn Marquardt <flynn@flynnux.de>
CC: <stable@kernel.org> [after .39-rc1 is out]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Save the last event in the otg_transceiver so that it can used in the
musb driver and gadget driver to configure the musb and enable the
vbus for host mode and OTG mode, if the device is connected during boot.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We don't use it so we can trim it from here as we try and stamp the file
object dependencies out of the serial code.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doing tiocmget was such fun we should do tiocmset as well for the same
reasons
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't actually need this and it causes problems for internal use of
this functionality. Currently there is a single use of the FILE * pointer.
That is the serial core which uses it to check tty_hung_up_p. However if
that is true then IO_ERROR is also already set so the check may be removed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed to resolve some merge conflicts that were found
in the USB host controller patches, and reported by Stephen Rothwell.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (21 commits)
USB: cdc-acm: Adding second ACM channel support for Nokia N8
USB, Mass Storage, composite, gadget: Fix build failure and memset of a struct
USB: Fix trout build failure with ci13xxx_msm gadget
USB: EHCI: fix scheduling while atomic during suspend
USB: usb-storage: unusual_devs entry for Coby MP3 player
USB: ftdi_sio: Add VID=0x0647, PID=0x0100 for Acton Research spectrograph
USB: fix race between root-hub resume and wakeup requests
USB: prevent buggy hubs from crashing the USB stack
usb: r8a66597-udc: Fixed bufnum of Bulk
USB: ftdi_sio: add ST Micro Connect Lite uart support
USB: Storage: Add unusual_devs entry for VTech Kidizoom
USB SL811HS HCD: Fix memory leak in sl811h_urb_enqueue()
USB: ti_usb: fix module removal
USB: io_edgeport: fix the reported firmware major and minor
usb: ehci-omap: Show fatal probing time errors to end user
usb: musb: introduce api for dma code to check compatibility with usb request
usb: musb: maintain three states for buffer mappings instead of two
usb: musb: disable double buffering when it's broken
usb: musb: hsdma: change back to use musb_read/writew
usb: musb: core: fix IRQ check
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
virtio_net: Add schedule check to napi_enable call
x25: Do not reference freed memory.
pch_can: fix tseg1/tseg2 setting issue
isdn: hysdn: Kill (partially buggy) CVS regision log reporting.
can: softing_cs needs slab.h
pch_gbe: Fix the issue which a driver locks when rx offload is set by ethtool
netfilter: nf_conntrack: set conntrack templates again if we return NF_REPEAT
pch_can: fix module reload issue with MSI
pch_can: fix rmmod issue
pch_can: fix 800k comms issue
net: Fix lockdep regression caused by initializing netdev queues too early.
net/caif: Fix dangling list pointer in freed object on error.
USB CDC NCM errata updates for cdc_ncm host driver
CDC NCM errata updates for cdc.h
ixgbe: update version string
ixgbe: cleanup variable initialization
ixgbe: limit VF access to network traffic
ixgbe: fix for 82599 erratum on Header Splitting
ixgbe: fix variable set but not used warnings by gcc 4.6
e1000: add support for Marvell Alaska M88E1118R PHY
...
This patch fixes the below compilation errors.
CC drivers/usb/gadget/ci13xxx_msm.o
CC net/mac80211/led.o
drivers/usb/gadget/ci13xxx_msm.c: In function 'ci13xxx_msm_notify_event':
drivers/usb/gadget/ci13xxx_msm.c:42: error: 'USB_AHBBURST' undeclared (first use in this function)
drivers/usb/gadget/ci13xxx_msm.c:42: error: (Each undeclared identifier is reported only once
drivers/usb/gadget/ci13xxx_msm.c:42: error: for each function it appears in.)
drivers/usb/gadget/ci13xxx_msm.c:43: error: 'USB_AHBMODE' undeclared (first use in this function)
make[4]: *** [drivers/usb/gadget/ci13xxx_msm.o] Error 1
make[3]: *** [drivers/usb/gadget] Error 2
MSM USB driver is not supported on boards like trout (MSM7201) which
has an external PHY.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To compile functionfs userspace driver one needs definitions from
include/linux/usb/functionfs.h. This patch add this file to the list
of includes exported to userspace.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Provide optional hooks for the host controller driver to override the
default DMA mapping and unmapping routines. In general, these shouldn't
be necessary unless the host controller has special DMA requirements,
such as alignment contraints. If these are not specified, the
general usb_hcd_(un)?map_urb_for_dma functions will be used instead.
Also, pass the status to unmap_urb_for_dma so it can know whether the
DMA buffer has been overwritten.
Finally, add a flag to be used by these implementations if they
allocated a temporary buffer so it can be freed properly when unmapping.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The convention is to prefix symbols exported from the USB HCD core with
"usb_hcd". This change makes unmap_urb_setup_for_dma() and
unmap_urb_for_dma() consistent with that.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-linus' of master.kernel.org:/pub/scm/linux/kernel/git/sarah/xhci:
xhci: Remove more doorbell-related reads
xHCI: fix printk_ratelimit() usage
xHCI: replace dev_dbg() with xhci_dbg()
xHCI: fix cycle bit set in giveback_first_trb()
xHCI: remove redundant parameter in giveback_first_trb()
xHCI: fix queue_trb in isoc transfer
xhci: Use GFP_NOIO during device reset.
usb: Realloc xHCI structures after a hub is verified.
xhci: Do not run xhci_cleanup_msix with irq disabled
xHCI: synchronize irq in xhci_suspend()
xhci: Resume bus on any port status change.
Alan's commit 335f8514f2 introduced
.carrier_raised function in several drivers. That also means
tty_port_block_til_ready can now suspend the process trying to open the serial
port when Carrier Detect is low and put it into tty_port.open_wait queue. We
need to wake up the process when Carrier Detect goes high and trigger TTY
hangup when CD goes low.
Some of the devices do not report modem status line changes, or at least we
don't understand the status message, so for those we remove .carrier_raised
again.
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Synchronize the interrupts instead of free them in xhci_suspend(). This will
prevent a double free when the host is suspended and then the card removed.
Set the flag hcd->msix_enabled when using MSI-X, and check the flag in
suspend_common(). MSI-X synchronization will be handled by xhci_suspend(),
and MSI/INTx will be synchronized in suspend_common().
This patch should be queued for the 2.6.37 stable tree.
Reported-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
Implement runtime and system pm ops to put hardware into low power
mode (LPM). As part of LPM, USB clocks are turned off, PHY is put
into suspend state and PHY comparators are turned off if VBUS/Id
notifications are not required from PHY.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver implements PHY initialization, clock management, ULPI IO ops
and simple OTG state machine to kick host/peripheral based on Id/VBUS
line status. VBUS/Id lines are tied to a reference voltage on some boards.
Hence provide debugfs interface to select host/peripheral mode.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the NOP USB OTG transceiver driver is built as a module, the otg.h
header declares external functions, but if they are referenced from the
kernel proper, as, e.g., in the OMAP3 case, where the omap3evm board is
calling the usb_nop_xceiv_register() function, linkage breaks. This patch
fixes this problem.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
