When a tablet connect or disconnect is detected, schedule
work queue to register or unregister related input devices.
When a wireless tablet connects, it reports same USB PID
used if tablet is connected with USB cable. Use this to
update features values, set input capabilities, and then
register device. From there, the Pen and Touch interfaces
will reuse the existing tablet's IRQ routines.
Its possible that 1 receiver is shared with 2 tablets with
different PID (small and medium Bamboo for example) so the
input is unregister at disconnect to better support this case.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The 3rd gen Bamboo Pen & Touch and Intuos5 tablets support an
optional wireless module. When its receiver is plugged into USB,
it presents 3 interfaces: 0) Monitor 1) Pen and 2) Touch.
The exact capabilities of the Pen and Touch interfaces can
not be determined until a tablet connection is established
and reported over the Monitor interface.
This patch detects this wireless receiver and enables interrupt
packets to be processed for the Monitor interface. Processing
the data in packets will be left to another patch.
Since it doesn't make sense to create an input device for the
Monitor interface, it is not created. Creation of Pen and Touch
input device is also delayed until monitor packets can be processed.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
And add two new data formats.
Tested-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adds support for the Cintiq 24HD. There are two quirks about this
model that haven't been seen in prior tablets. First, a second
touch ring is present on this display; it is being exposed via the
ABS_THROTTLE axis. Second, three capacitive buttons at the top of
the unit are available; though physically a touch strip, we report
the use of these buttons with generic KEY_ events.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
3rd generation Bamboo Pen and Touch tablets reuse the older
stylus packet but add an extra fixed zero pad byte to end.
The touch packets are quite different since it supports tracking
of up to 16 touches. The packet is 64-byte fixed size but contains
up to 15 smaller messages indicating data for a single touch or
for tablet button presses.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Override invalid pen based pktlen and x/y_max with touch
values from HID report.
Since active area of pen and touch are same on these
devices, set physical x/y size while pen x/y_max and
resolution are still valid.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Touch resolution is reported to the userland by retrieving the value
from the HID descriptor. But pen resolution is not since it can not
be retrieved. The current Wacom X driver has a resolution table.
To centralize the source of these values, the resolution entries are
added in the wacom_features struct for x and y coordinates respectively.
The values are then reported to the userland.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are two types of 1FGT devices supported in wacom_wac.c.
Changing them to follow the existing touchscreen format, i.e.,
only report BTN_TOUCH as a valid tool type.
Touch data will be ignored if pen is in proximity. This requires
a touch up event sent if touch was down when pen comes in. The
touch up event should be sent before any pen events are emitted.
Otherwise, two pointers would race for the cursor.
However, we can not send a touch up inside wacom_tpc_pen since
pen and touch are on different logical port. That is why we
have to check if touch is up before sending pen events.
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2FGT Tablet PC touch events were processed in _TAP_ format. Remove
them so we can change to _MT_ format.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The drivers using the type B protocol all report tracking information
the same way. The contact id is semantically equivalent to
ABS_MT_SLOT, and the handling of ABS_MT_TRACKING_ID only complicates
the driver. The situation can be improved upon by providing a common
pointer emulation code, thereby removing the need for the tracking id
in the driver. This patch moves all tracking event handling over to
the input core, simplifying both the existing drivers and the ones
currently in preparation.
Acked-by: Ping Cheng <pingc@wacom.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The Bamboo Touch reports a sub-screen resolution of 480x320. The
signal-to-noise ratio is only about 100, so filtering is needed in
order to reduce the jitter to a usable level. However, the low
resolution leads to round-off errors in the EWMA filter, resulting in
extremely jerky pointer motion. This patch explicitly sets a higher
resolution for those devices, and tells this to the completion handler
via a low-resolution quirk.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support for the Bamboo Touch trackpad, and make it work with
both the Synaptics X Driver and the Multitouch X Driver. The device
uses MT slots internally, so the choice of protocol is a given.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Collect device-specific code into a single function, and use quirks to
flag specific behavior instead.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Bamboo devices have multiple interfaces which need to be setup
separately. Use the HID parsing mechanism to achieve that.
Signed-off-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The signal-to-noise ratio varies between devices, but currently all
devices are treated the same way. Add fuzz parameters to the feature
struct, allowing for tailored treatment of devices.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Clean up 2-finger touch support. This still needs to be converted to
proper multi-touch protocol.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Input event interface is pretty stable so let's get rig of wrappers
for input_event() and fiends and call them directly. This will simplify
and speed up code a bit.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is no reason for allocating struct wacom_wac separately from
struct wacom since both have the same lifetime rules and are not
shared. Also make 'open' field a boolean.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Touch enbaled devices share the same product ID with pen. However,
we do not want to post touch events while pen is in prox. To do so,
we used to keep a local static variable to keep track of if pen is
in prox or not. This works fine for Tablet PC devices since there
is only one device attached. With the newer touch enabled regular
tablets, we can not make this assumption any more, i.e, one system
may have more than one identical tablet plugged in.
This patch adds an new entry, shared, into the struct wacom_wac so
touch data can access pen data to locally. This solution assumes
the two tools (touch and pen) of the same ID will be probed one
after the other without interruption in between by another Wacom
device of the same ID.
Replacing WACOM_PKGLEN_PENABLED with WACOM_PKGLEN_GRAPHIRE since
they both represent the same value, 8. This value will be used
for both Tablet PC and Bamboo with touch devices.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Devices supporting both pen and touch features share the same product ID,
but presented as 2 separate input devices. By adding device type to device
name string we can help userspace applications and users differentiate
between them. 'Finger' is used for the touch since touch has been used as
a suffix by userland hotplugging services.
Signed-off-by: Jason Childs <oblivian@users.sourceforge.net>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since we mangle data in wacom_features when dealing with certain devices let's
use a private (per-device) instance of wacom_features in wacom_wac. This way
same product ID can support more than one type of device, such as pen and touch,
and not interfere with each other.
Signed-off-by: Jason Childs <oblivian@users.sourceforge.net>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds support for the foolowing Wacom devices:
- 0x9F - a single touch only LCD tablet;
- 0xE2 - a two finger touch only LCD tablet;
- 0xE3 - a two finger touch, penabled LCD tablet.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support for new wacom tablets - Bamboo1, BambooFun, and Cintiq 12WX
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This will allow concentrating all input devices in one place
in {menu|x|q}config.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-05-08 01:41:29 -04:00
Renamed from drivers/usb/input/wacom_wac.h (Browse further)
