Add "always lock'd" implementations of set_bit, clear_bit and change_bit and
the corresponding test_and_ functions. Also add "always lock'd"
implementation of cmpxchg. These give guaranteed strong synchronisation and
are required for non-SMP kernels running on an SMP hypervisor.
Signed-off-by: Ian Pratt <ian.pratt@xensource.com>
Signed-off-by: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patchset adds the necessary drivers and infrastructure to access the
external flash on the ATSTK1000 board through the MTD subsystem. With this
stuff in place, it will be possible to use a jffs2 filesystem stored in the
external flash as a root filesystem. It might also be possible to update the
boot loader if you drop the write protection of partition 0.
As suggested by David Woodhouse, I reworked the patches to use the physmap
driver instead of introducing a separate mapping driver for the ATSTK1000.
I've also cleaned up the hsmc header by removing useless comments and
converting spaces to tabs (my headerfile generator needs some work.)
Unfortunately, I couldn't unlock the flash in fixup_use_atmel_lock because the
erase regions hadn't been set up yet, so I had to do it from cfi_amdstd_setup
instead.
This patch:
This adds a simple API for configuring the static memory controller along with
an implementation for the Atmel HSMC.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds support for the Atmel AVR32 architecture as well as the AT32AP7000
CPU and the AT32STK1000 development board.
AVR32 is a new high-performance 32-bit RISC microprocessor core, designed for
cost-sensitive embedded applications, with particular emphasis on low power
consumption and high code density. The AVR32 architecture is not binary
compatible with earlier 8-bit AVR architectures.
The AVR32 architecture, including the instruction set, is described by the
AVR32 Architecture Manual, available from
http://www.atmel.com/dyn/resources/prod_documents/doc32000.pdf
The Atmel AT32AP7000 is the first CPU implementing the AVR32 architecture. It
features a 7-stage pipeline, 16KB instruction and data caches and a full
Memory Management Unit. It also comes with a large set of integrated
peripherals, many of which are shared with the AT91 ARM-based controllers from
Atmel.
Full data sheet is available from
http://www.atmel.com/dyn/resources/prod_documents/doc32003.pdf
while the CPU core implementation including caches and MMU is documented by
the AVR32 AP Technical Reference, available from
http://www.atmel.com/dyn/resources/prod_documents/doc32001.pdf
Information about the AT32STK1000 development board can be found at
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3918
including a BSP CD image with an earlier version of this patch, development
tools (binaries and source/patches) and a root filesystem image suitable for
booting from SD card.
Alternatively, there's a preliminary "getting started" guide available at
http://avr32linux.org/twiki/bin/view/Main/GettingStarted which provides links
to the sources and patches you will need in order to set up a cross-compiling
environment for avr32-linux.
This patch, as well as the other patches included with the BSP and the
toolchain patches, is actively supported by Atmel Corporation.
[dmccr@us.ibm.com: Fix more pxx_page macro locations]
[bunk@stusta.de: fix `make defconfig']
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave McCracken <dmccr@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The third argument of au1xxx_dbdma_chan_alloc's callback function is not
used anywhere.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Optimise ffs(x) by using fls(x & x - 1) which we optimise to use the SCAN
instruction.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement fls64() for FRV without recource to conditional jumps.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix FRV fls() to handle bit 31 being set correctly (it should return 32 not 0).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Permit __do_IRQ() to be dispensed with based on a configuration option.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the FRV arch use the generic IRQ code rather than having its own
routines for doing so.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace ctxid with sid in selinux_audit_rule_match interface for
consistency with other interfaces.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename selinux_ctxid_to_string to selinux_sid_to_string to be
consistent with other interfaces.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Eliminate selinux_task_ctxid since it duplicates selinux_task_get_sid.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are many places where we need to determine the node of a zone.
Currently we use a difficult to read sequence of pointer dereferencing.
Put that into an inline function and use throughout VM. Maybe we can find
a way to optimize the lookup in the future.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently one can enable slab reclaim by setting an explicit option in
/proc/sys/vm/zone_reclaim_mode. Slab reclaim is then used as a final
option if the freeing of unmapped file backed pages is not enough to free
enough pages to allow a local allocation.
However, that means that the slab can grow excessively and that most memory
of a node may be used by slabs. We have had a case where a machine with
46GB of memory was using 40-42GB for slab. Zone reclaim was effective in
dealing with pagecache pages. However, slab reclaim was only done during
global reclaim (which is a bit rare on NUMA systems).
This patch implements slab reclaim during zone reclaim. Zone reclaim
occurs if there is a danger of an off node allocation. At that point we
1. Shrink the per node page cache if the number of pagecache
pages is more than min_unmapped_ratio percent of pages in a zone.
2. Shrink the slab cache if the number of the nodes reclaimable slab pages
(patch depends on earlier one that implements that counter)
are more than min_slab_ratio (a new /proc/sys/vm tunable).
The shrinking of the slab cache is a bit problematic since it is not node
specific. So we simply calculate what point in the slab we want to reach
(current per node slab use minus the number of pages that neeed to be
allocated) and then repeately run the global reclaim until that is
unsuccessful or we have reached the limit. I hope we will have zone based
slab reclaim at some point which will make that easier.
The default for the min_slab_ratio is 5%
Also remove the slab option from /proc/sys/vm/zone_reclaim_mode.
[akpm@osdl.org: cleanups]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the atomic counter for slab_reclaim_pages and replace the counter
and NR_SLAB with two ZVC counter that account for unreclaimable and
reclaimable slab pages: NR_SLAB_RECLAIMABLE and NR_SLAB_UNRECLAIMABLE.
Change the check in vmscan.c to refer to to NR_SLAB_RECLAIMABLE. The
intend seems to be to check for slab pages that could be freed.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
*_pages is a better description of the role of the variable.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One of the changes necessary for shared page tables is to standardize the
pxx_page macros. pte_page and pmd_page have always returned the struct
page associated with their entry, while pte_page_kernel and pmd_page_kernel
have returned the kernel virtual address. pud_page and pgd_page, on the
other hand, return the kernel virtual address.
Shared page tables needs pud_page and pgd_page to return the actual page
structures. There are very few actual users of these functions, so it is
simple to standardize their usage.
Since this is basic cleanup, I am submitting these changes as a standalone
patch. Per Hugh Dickins' comments about it, I am also changing the
pxx_page_kernel macros to pxx_page_vaddr to clarify their meaning.
Signed-off-by: Dave McCracken <dmccr@us.ibm.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In many places we will need to use the same combination of flags. Specify
a single GFP_THISNODE definition for ease of use in gfp.h.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new gfp flag __GFP_THISNODE to avoid fallback to other nodes. This
flag is essential if a kernel component requires memory to be located on a
certain node. It will be needed for alloc_pages_node() to force allocation
on the indicated node and for alloc_pages() to force allocation on the
current node.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Let's try to keep mm/ comments more useful and up to date. This is a start.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce ARCH_LOW_ADDRESS_LIMIT which can be set per architecture to
override the 4GB default limit used by the bootmem allocater within
__alloc_bootmem_low() and __alloc_bootmem_low_node(). E.g. s390 needs a
2GB limit instead of 4GB.
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
lock_page needs the caller to have a reference on the page->mapping inode
due to sync_page, ergo set_page_dirty_lock is obviously buggy according to
its comments.
Solve it by introducing a new lock_page_nosync which does not do a sync_page.
akpm: unpleasant solution to an unpleasant problem. If it goes wrong it could
cause great slowdowns while the lock_page() caller waits for kblockd to
perform the unplug. And if a filesystem has special sync_page() requirements
(none presently do), permanent hangs are possible.
otoh, set_page_dirty_lock() is usually (always?) called against userspace
pages. They are always up-to-date, so there shouldn't be any pending read I/O
against these pages.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch splits alloc_percpu() up into two phases. Likewise for
free_percpu(). This allows clients to limit initial allocations to online
cpu's, and to populate or depopulate per-cpu data at run time as needed:
struct my_struct *obj;
/* initial allocation for online cpu's */
obj = percpu_alloc(sizeof(struct my_struct), GFP_KERNEL);
...
/* populate per-cpu data for cpu coming online */
ptr = percpu_populate(obj, sizeof(struct my_struct), GFP_KERNEL, cpu);
...
/* access per-cpu object */
ptr = percpu_ptr(obj, smp_processor_id());
...
/* depopulate per-cpu data for cpu going offline */
percpu_depopulate(obj, cpu);
...
/* final removal */
percpu_free(obj);
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a notifer chain to the out of memory killer. If one of the registered
callbacks could release some memory, do not kill the process but return and
retry the allocation that forced the oom killer to run.
The purpose of the notifier is to add a safety net in the presence of
memory ballooners. If the resource manager inflated the balloon to a size
where memory allocations can not be satisfied anymore, it is better to
deflate the balloon a bit instead of killing processes.
The implementation for the s390 ballooner is included.
[akpm@osdl.org: cleanups]
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I wonder why we need this bitmask indexing into zone->node_zonelists[]?
We always start with the highest zone and then include all lower zones
if we build zonelists.
Are there really cases where we need allocation from ZONE_DMA or
ZONE_HIGHMEM but not ZONE_NORMAL? It seems that the current implementation
of highest_zone() makes that already impossible.
If we go linear on the index then gfp_zone() == highest_zone() and a lot
of definitions fall by the wayside.
We can now revert back to the use of gfp_zone() in mempolicy.c ;-)
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After we have done this we can now do some typing cleanup.
The memory policy layer keeps a policy_zone that specifies
the zone that gets memory policies applied. This variable
can now be of type enum zone_type.
The check_highest_zone function and the build_zonelists funnctionm must
then also take a enum zone_type parameter.
Plus there are a number of loops over zones that also should use
zone_type.
We run into some troubles at some points with functions that need a
zone_type variable to become -1. Fix that up.
[pj@sgi.com: fix set_mempolicy() crash]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a check in zonelist_policy that compares pieces of the bitmap
obtained from a gfp mask via GFP_ZONETYPES with a zone number in function
zonelist_policy().
The bitmap is an ORed mask of __GFP_DMA, __GFP_DMA32 and __GFP_HIGHMEM.
The policy_zone is a zone number with the possible values of ZONE_DMA,
ZONE_DMA32, ZONE_HIGHMEM and ZONE_NORMAL. These are two different domains
of values.
For some reason seemed to work before the zone reduction patchset (It
definitely works on SGI boxes since we just have one zone and the check
cannot fail).
With the zone reduction patchset this check definitely fails on systems
with two zones if the system actually has memory in both zones.
This is because ZONE_NORMAL is selected using no __GFP flag at
all and thus gfp_zone(gfpmask) == 0. ZONE_DMA is selected when __GFP_DMA
is set. __GFP_DMA is 0x01. So gfp_zone(gfpmask) == 1.
policy_zone is set to ZONE_NORMAL (==1) if ZONE_NORMAL and ZONE_DMA are
populated.
For ZONE_NORMAL gfp_zone(<no _GFP_DMA>) yields 0 which is <
policy_zone(ZONE_NORMAL) and so policy is not applied to regular memory
allocations!
Instead gfp_zone(__GFP_DMA) == 1 which results in policy being applied
to DMA allocations!
What we realy want in that place is to establish the highest allowable
zone for a given gfp_mask. If the highest zone is higher or equal to the
policy_zone then memory policies need to be applied. We have such
a highest_zone() function in page_alloc.c.
So move the highest_zone() function from mm/page_alloc.c into
include/linux/gfp.h. On the way we simplify the function and use the new
zone_type that was also introduced with the zone reduction patchset plus we
also specify the right type for the gfp flags parameter.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
eventcounters: Do not display counters for zones that are not available on an
arch
Do not define or display counters for the DMA32 and the HIGHMEM zone if such
zones were not configured.
[akpm@osdl.org: s390 fix]
[heiko.carstens@de.ibm.com: s390 fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make ZONE_HIGHMEM optional
- ifdef out code and definitions related to CONFIG_HIGHMEM
- __GFP_HIGHMEM falls back to normal allocations if there is no
ZONE_HIGHMEM
- GFP_ZONEMASK becomes 0x01 if there is no DMA32 and no HIGHMEM
zone.
[jdike@addtoit.com: build fix]
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make ZONE_DMA32 optional
- Add #ifdefs around ZONE_DMA32 specific code and definitions.
- Add CONFIG_ZONE_DMA32 config option and use that for x86_64
that alone needs this zone.
- Remove the use of CONFIG_DMA_IS_DMA32 and CONFIG_DMA_IS_NORMAL
for ia64 and fix up the way per node ZVCs are calculated.
- Fall back to prior GFP_ZONEMASK of 0x03 if there is no
DMA32 zone.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use enum for zones and reformat zones dependent information
Add comments explaning the use of zones and add a zones_t type for zone
numbers.
Line up information that will be #ifdefd by the following patches.
[akpm@osdl.org: comment cleanups]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move totalhigh_pages and nr_free_highpages() into highmem.c/.h
Move the totalhigh_pages definition into highmem.c/.h. Move the
nr_free_highpages function into highmem.c
[yoichi_yuasa@tripeaks.co.jp: build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It fixes various coding style issues, specially when spaces are useless. For
example '*' go next to the function name.
Signed-off-by: Franck Bui-Huu <vagabon.xyz@gmail.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__init in headers is pretty useless because the compiler doesn't check it, and
they get out of sync relatively frequently. So if you see an __init in a
header file, it's quite unreliable and you need to check the definition
anyway.
Signed-off-by: Franck Bui-Huu <vagabon.xyz@gmail.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Address a long standing issue of booting with an initrd on an i386 numa
system. Currently (and always) the numa kva area is mapped into low memory
by finding the end of low memory and moving that mark down (thus creating
space for the kva). The issue with this is that Grub loads initrds into
this similar space so when the kernel check the initrd it finds it outside
max_low_pfn and disables it (it thinks the initrd is not mapped into usable
memory) thus initrd enabled kernels can't boot i386 numa :(
My solution to the problem just converts the numa kva area to use the
bootmem allocator to save it's area (instead of moving the end of low
memory). Using bootmem allows the kva area to be mapped into more diverse
addresses (not just the end of low memory) and enables the kva area to be
mapped below the initrd if present.
I have tested this patch on numaq(no initrd) and summit(initrd) i386 numa
based systems.
[akpm@osdl.org: cleanups]
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes the following needlessly global functions static:
- slab.c: kmem_find_general_cachep()
- swap.c: __page_cache_release()
- vmalloc.c: __vmalloc_node()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that we can detect writers of shared mappings, throttle them. Avoids OOM
by surprise.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tracking of dirty pages in shared writeable mmap()s.
The idea is simple: write protect clean shared writeable pages, catch the
write-fault, make writeable and set dirty. On page write-back clean all the
PTE dirty bits and write protect them once again.
The implementation is a tad harder, mainly because the default
backing_dev_info capabilities were too loosely maintained. Hence it is not
enough to test the backing_dev_info for cap_account_dirty.
The current heuristic is as follows, a VMA is eligible when:
- its shared writeable
(vm_flags & (VM_WRITE|VM_SHARED)) == (VM_WRITE|VM_SHARED)
- it is not a 'special' mapping
(vm_flags & (VM_PFNMAP|VM_INSERTPAGE)) == 0
- the backing_dev_info is cap_account_dirty
mapping_cap_account_dirty(vma->vm_file->f_mapping)
- f_op->mmap() didn't change the default page protection
Page from remap_pfn_range() are explicitly excluded because their COW
semantics are already horrid enough (see vm_normal_page() in do_wp_page()) and
because they don't have a backing store anyway.
mprotect() is taught about the new behaviour as well. However it overrides
the last condition.
Cleaning the pages on write-back is done with page_mkclean() a new rmap call.
It can be called on any page, but is currently only implemented for mapped
pages, if the page is found the be of a VMA that accounts dirty pages it will
also wrprotect the PTE.
Finally, in fs/buffers.c:try_to_free_buffers(); remove clear_page_dirty() from
under ->private_lock. This seems to be safe, since ->private_lock is used to
serialize access to the buffers, not the page itself. This is needed because
clear_page_dirty() will call into page_mkclean() and would thereby violate
locking order.
[dhowells@redhat.com: Provide a page_mkclean() implementation for NOMMU]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce a VM_BUG_ON, which is turned on with CONFIG_DEBUG_VM. Use this
in the lightweight, inline refcounting functions; PageLRU and PageActive
checks in vmscan, because they're pretty well confined to vmscan. And in
page allocate/free fastpaths which can be the hottest parts of the kernel
for kbuilds.
Unlike BUG_ON, VM_BUG_ON must not be used to execute statements with
side-effects, and should not be used outside core mm code.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Give non-highmem architectures access to the kmap API for the purposes of
overriding (this is what the attached patch does).
The proposal is that we should now require all architectures with coherence
issues to manage data coherence via the kmap/kunmap API. Thus driver
writers never have to write code like
kmap(page)
modify data in page
flush_kernel_dcache_page(page)
kunmap(page)
instead, kmap/kunmap will manage the coherence and driver (and filesystem)
writers don't need to worry about how to flush between kmap and kunmap.
For most architectures, the page only needs to be flushed if it was
actually written to *and* there are user mappings of it, so the best
implementation looks to be: clear the page dirty pte bit in the kernel page
tables on kmap and on kunmap, check page->mappings for user maps, and then
the dirty bit, and only flush if it both has user mappings and is dirty.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
get_cpu_var()/per_cpu()/__get_cpu_var() arguments must be simple
identifiers. Otherwise the arch dependent implementations might break.
This patch enforces the correct usage of the macros by producing a syntax
error if the variable is not a simple identifier.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NetLabel]: update docs with website information
[NetLabel]: rework the Netlink attribute handling (part 2)
[NetLabel]: rework the Netlink attribute handling (part 1)
[Netlink]: add nla_validate_nested()
[NETLINK]: add nla_for_each_nested() to the interface list
[NetLabel]: change the SELinux permissions
[NetLabel]: make the CIPSOv4 cache spinlocks bottom half safe
[NetLabel]: correct improper handling of non-NetLabel peer contexts
[TCP]: make cubic the default
[TCP]: default congestion control menu
[ATM] he: Fix __init/__devinit conflict
[NETFILTER]: Add dscp,DSCP headers to header-y
[DCCP]: Introduce dccp_probe
[DCCP]: Use constants for CCIDs
[DCCP]: Introduce constants for CCID numbers
[DCCP]: Allow default/fallback service code.
Assume that a cpu is *physically* offlined at boot time...
Because smpboot.c::smp_boot_cpu_map() canoot find cpu's sapicid,
numa.c::build_cpu_to_node_map() cannot build cpu<->node map for
offlined cpu.
For such cpus, cpu_to_node map should be fixed at cpu-hot-add.
This mapping should be done before cpu onlining.
This patch also handles cpu hotremove case.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At the suggestion of Thomas Graf, rewrite NetLabel's use of Netlink attributes
to better follow the common Netlink attribute usage.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function, nla_validate_nested(), to validate nested Netlink
attributes.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
