Ethernet MAC drivers based on phylib (but not using NAPI) can
enable hardware time stamping in phy devices by calling netif_rx()
conditionally based on a call to skb_defer_rx_timestamp().
This commit exports that function so that drivers calling it may
be compiled as modules.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
AFS: Use i_generation not i_version for the vnode uniquifier
AFS: Set s_id in the superblock to the volume name
vfs: Fix data corruption after failed write in __block_write_begin()
afs: afs_fill_page reads too much, or wrong data
VFS: Fix vfsmount overput on simultaneous automount
fix wrong iput on d_inode introduced by e6bc45d65d
Delay struct net freeing while there's a sysfs instance refering to it
afs: fix sget() races, close leak on umount
ubifs: fix sget races
ubifs: split allocation of ubifs_info into a separate function
fix leak in proc_set_super()
The network stack provides the function, skb_clone_tx_timestamp().
Ethernet MAC drivers can call this via the transmit time stamping
hook, skb_tx_timestamp(). This commit exports the clone function so
that drivers using it can be compiled as modules.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
* new refcount in struct net, controlling actual freeing of the memory
* new method in kobj_ns_type_operations (->drop_ns())
* ->current_ns() semantics change - it's supposed to be followed by
corresponding ->drop_ns(). For struct net in case of CONFIG_NET_NS it bumps
the new refcount; net_drop_ns() decrements it and calls net_free() if the
last reference has been dropped. Method renamed to ->grab_current_ns().
* old net_free() callers call net_drop_ns() instead.
* sysfs_exit_ns() is gone, along with a large part of callchain
leading to it; now that the references stored in ->ns[...] stay valid we
do not need to hunt them down and replace them with NULL. That fixes
problems in sysfs_lookup() and sysfs_readdir(), along with getting rid
of sb->s_instances abuse.
Note that struct net *shutdown* logics has not changed - net_cleanup()
is called exactly when it used to be called. The only thing postponed by
having a sysfs instance refering to that struct net is actual freeing of
memory occupied by struct net.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
There is a dev_put(ndev) missing on an error path. This was
introduced in 0c1ad04aec "netpoll: prevent netpoll setup on slave
devices".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing of VLAN_FLAG_REORDER_HDR does not belong in vlan_untag
but rather in vlan_do_receive. Otherwise the vlan header
will not be properly put on the packet in the case of
vlan header accelleration.
As we remove the check from vlan_check_reorder_header
rename it vlan_reorder_header to keep the naming clean.
Fix up the skb->pkt_type early so we don't look at the packet
after adding the vlan tag, which guarantees we don't goof
and look at the wrong field.
Use a simple if statement instead of a complicated switch
statement to decided that we need to increment rx_stats
for a multicast packet.
Hopefully at somepoint we will just declare the case where
VLAN_FLAG_REORDER_HDR is cleared as unsupported and remove
the code. Until then this keeps it working correctly.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message size allocated for rtnl ifinfo dumps was limited to
a single page. This is not enough for additional interface info
available with devices that support SR-IOV and caused a bug in
which VF info would not be displayed if more than approximately
40 VFs were created per interface.
Implement a new function pointer for the rtnl_register service that will
calculate the amount of data required for the ifinfo dump and allocate
enough data to satisfy the request.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 8d8fc29d02
(netpoll: disable netpoll when enslave a device), we automatically
disable netpoll when the underlying device is being enslaved,
we also need to prevent people from setuping netpoll on
devices that are already enslaved.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to remove all support for displaying an ntuple as
strings via ETHTOOL_GRXNTUPLE. The reason for this change is due to the
fact that multiple issues have been found including:
- Multiple buffer overruns for strings being displayed.
- Incorrect filters displayed, cleared filters with ring of -2 are displayed
- Setting get_rx_ntuple displays no rules if defined.
- Endianess wrong on displayed values.
- Hard limit of 1024 filters makes display functionality extremely limited
The only driver that had supported this interface was ixgbe. Since it no
longer uses the interface and due to the issues mentioned above I am
submitting this patch to remove it.
v2:
Updated based on comments from Ben Hutchings
- Left ETH_SS_NTUPLE_FILTERS in code but commented on it being deprecated
- Removed ethtool_rx_ntuple_list and ethtool_rx_ntuple_flow_spec_container
- Left ETHTOOL_GRXNTUPLE but commented it as deprecated
Also cleaned up set_rx_ntuple since there is no flow spec container to
maintain we can drop all the code for the alloc and free of it and just
return ops->set_rx_ntuple().
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Blaschka reported :
<quote>
During heavy network load we turn off/on cpus.
Sometimes this causes a stall on the network device.
Digging into the dump I found out following:
napi is scheduled but does not run. From the I/O buffers
and the napi state I see napi/rx_softirq processing has stopped
because the budget was reached. napi stays in the
softnet_data poll_list and the rx_softirq was raised again.
I assume at this time the cpu offline comes in,
the rx softirq is raised/moved to another cpu but napi stays in the
poll_list of the softnet_data of the now offline cpu.
Reviewing dev_cpu_callback (net/core/dev.c) I did not find the
poll_list is transfered to the new cpu.
</quote>
This patch is a straightforward implementation of Frank suggestion :
Transfert poll_list and trigger NET_RX_SOFTIRQ on new cpu.
Reported-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface uses a temporary buffer, but for no real reason.
And now can generate warnings like:
net/sched/sch_generic.c: In function dev_watchdog
net/sched/sch_generic.c:254:10: warning: unused variable drivername
Just return driver->name directly or "".
Reported-by: Connor Hansen <cmdkhh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BTW, looking through the code related to struct net lifetime rules has
caught something else:
struct net *get_net_ns_by_fd(int fd)
{
...
file = proc_ns_fget(fd);
if (!file)
goto out;
ei = PROC_I(file->f_dentry->d_inode);
while in proc_ns_fget() we have two return ERR_PTR(...) and not a single
path that would return NULL. The other caller of proc_ns_fget() treats
ERR_PTR() correctly...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits)
tg3: Fix tg3_skb_error_unmap()
net: tracepoint of net_dev_xmit sees freed skb and causes panic
drivers/net/can/flexcan.c: add missing clk_put
net: dm9000: Get the chip in a known good state before enabling interrupts
drivers/net/davinci_emac.c: add missing clk_put
af-packet: Add flag to distinguish VID 0 from no-vlan.
caif: Fix race when conditionally taking rtnl lock
usbnet/cdc_ncm: add missing .reset_resume hook
vlan: fix typo in vlan_dev_hard_start_xmit()
net/ipv4: Check for mistakenly passed in non-IPv4 address
iwl4965: correctly validate temperature value
bluetooth l2cap: fix locking in l2cap_global_chan_by_psm
ath9k: fix two more bugs in tx power
cfg80211: don't drop p2p probe responses
Revert "net: fix section mismatches"
drivers/net/usb/catc.c: Fix potential deadlock in catc_ctrl_run()
sctp: stop pending timers and purge queues when peer restart asoc
drivers/net: ks8842 Fix crash on received packet when in PIO mode.
ip_options_compile: properly handle unaligned pointer
iwlagn: fix incorrect PCI subsystem id for 6150 devices
...
Because there is a possibility that skb is kfree_skb()ed and zero cleared
after ndo_start_xmit, we should not see the contents of skb like skb->len and
skb->dev->name after ndo_start_xmit. But trace_net_dev_xmit does that
and causes panic by NULL pointer dereference.
This patch fixes trace_net_dev_xmit not to see the contents of skb directly.
If you want to reproduce this panic,
1. Get tracepoint of net_dev_xmit on
2. Create 2 guests on KVM
2. Make 2 guests use virtio_net
4. Execute netperf from one to another for a long time as a network burden
5. host will panic(It takes about 30 minutes)
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Kill ratelimit.h dependency in linux/net.h
net: Add linux/sysctl.h includes where needed.
net: Kill ether_table[] declaration.
inetpeer: fix race in unused_list manipulations
atm: expose ATM device index in sysfs
IPVS: bug in ip_vs_ftp, same list heaad used in all netns.
bug.h: Move ratelimit warn interfaces to ratelimit.h
bonding: cleanup module option descriptions
net:8021q:vlan.c Fix pr_info to just give the vlan fullname and version.
net: davinci_emac: fix dev_err use at probe
can: convert to %pK for kptr_restrict support
net: fix ETHTOOL_SFEATURES compatibility with old ethtool_ops.set_flags
netfilter: Fix several warnings in compat_mtw_from_user().
netfilter: ipset: fix ip_set_flush return code
netfilter: ipset: remove unused variable from type_pf_tdel()
netfilter: ipset: Use proper timeout value to jiffies conversion
Ingo Molnar noticed that we have this unnecessary ratelimit.h
dependency in linux/net.h, which hid compilation problems from
people doing builds only with CONFIG_NET enabled.
Move this stuff out to a seperate net/net_ratelimit.h file and
include that in the only two places where this thing is needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
As reported by Ingo Molnar, we still have configuration combinations
where use of the WARN_RATELIMIT interfaces break the build because
dependencies don't get met.
Instead of going down the long road of trying to make it so that
ratelimit.h can get included by kernel.h or asm-generic/bug.h,
just move the interface into ratelimit.h and make users have
to include that.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Current code squashes flags to bool - this makes set_flags fail whenever
some ETH_FLAG_* equivalent features are set. Fix this.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/linux-2.6-nsfd:
net: fix get_net_ns_by_fd for !CONFIG_NET_NS
ns proc: Return -ENOENT for a nonexistent /proc/self/ns/ entry.
ns: Declare sys_setns in syscalls.h
net: Allow setting the network namespace by fd
ns proc: Add support for the ipc namespace
ns proc: Add support for the uts namespace
ns proc: Add support for the network namespace.
ns: Introduce the setns syscall
ns: proc files for namespace naming policy.
Commit e67f88dd12 (dont hold rtnl mutex during netlink dump callbacks)
missed fact that rtnl_fill_ifinfo() must be called with rtnl held.
Because of possible deadlocks between two mutexes (cb_mutex and rtnl),
its not easy to solve this problem, so revert this part of the patch.
It also forgot one rcu_read_unlock() in FIB dump_rules()
Add one ASSERT_RTNL() in rtnl_fill_ifinfo() to remind us the rule.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device passed into dev_disable_lro is a vlan, then repoint the dev
poniter so that we actually modify the underlying physical device.
Signed-of-by: Neil Horman <nhorman@tuxdriver.com>
CC: davem@davemloft.net
CC: bhutchings@solarflare.com
Signed-off-by: David S. Miller <davem@davemloft.net>
After merging the final tree, today's linux-next build (powerpc
ppc44x_defconfig) failed like this:
net/built-in.o: In function `get_net_ns_by_fd':
(.text+0x11976): undefined reference to `netns_operations'
net/built-in.o: In function `get_net_ns_by_fd':
(.text+0x1197a): undefined reference to `netns_operations'
netns_operations is only available if CONFIG_NET_NS is set ...
Caused by commit f063052947 ("net: Allow setting the network namespace
by fd").
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
dst_default_metrics is readonly, we dont want to kfree() it later.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
synchronize_rcu() is very slow in various situations (HZ=100,
CONFIG_NO_HZ=y, CONFIG_PREEMPT=n)
Extract from my (mostly idle) 8 core machine :
synchronize_rcu() in 99985 us
synchronize_rcu() in 79982 us
synchronize_rcu() in 87612 us
synchronize_rcu() in 79827 us
synchronize_rcu() in 109860 us
synchronize_rcu() in 98039 us
synchronize_rcu() in 89841 us
synchronize_rcu() in 79842 us
synchronize_rcu() in 80151 us
synchronize_rcu() in 119833 us
synchronize_rcu() in 99858 us
synchronize_rcu() in 73999 us
synchronize_rcu() in 79855 us
synchronize_rcu() in 79853 us
When we hold RTNL mutex, we would like to spend some cpu cycles but not
block too long other processes waiting for this mutex.
We also want to setup/dismantle network features as fast as possible at
boot/shutdown time.
This patch makes synchronize_net() call the expedited version if RTNL is
locked.
synchronize_rcu_expedited() typical delay is about 20 us on my machine.
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 20 us
synchronize_rcu_expedited() in 16 us
synchronize_rcu_expedited() in 20 us
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 18 us
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
CC: Ben Greear <greearb@candelatech.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A mis-configured filter can spam the logs with lots of stack traces.
Rate-limit the warnings and add printout of the bogus filter information.
Original-patch-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also shrinks the object size a little.
text data bss dec hex filename
28834 186 8 29028 7164 net/core/pktgen.o
28816 186 8 29010 7152 net/core/pktgen.o.AFTER
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: "David Miller" <davem@davemloft.net>,
Signed-off-by: David S. Miller <davem@davemloft.net>
In the old days, we used to access dev->master in __netif_receive_skb()
in a rcu_read_lock section.
So one synchronize_net() call was needed in netdev_set_master() to make
sure another cpu could not use old master while/after we release it.
We now use netdev_rx_handler infrastructure and added one
synchronize_net() call in bond_release()/bond_release_all()
Remove the obsolete synchronize_net() from netdev_set_master() and add
one in bridge del_nbp() after its netdev_rx_handler_unregister() call.
This makes enslave -d a bit faster.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jiri Pirko <jpirko@redhat.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two events are not expected to be caught by userspace.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
Commit e66eed651f ("list: remove prefetching from regular list
iterators") removed the include of prefetch.h from list.h, which
uncovered several cases that had apparently relied on that rather
obscure header file dependency.
So this fixes things up a bit, using
grep -L linux/prefetch.h $(git grep -l '[^a-z_]prefetchw*(' -- '*.[ch]')
grep -L 'prefetchw*(' $(git grep -l 'linux/prefetch.h' -- '*.[ch]')
to guide us in finding files that either need <linux/prefetch.h>
inclusion, or have it despite not needing it.
There are more of them around (mostly network drivers), but this gets
many core ones.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When one macvlan device is dismantled, we can avoid one
synchronize_rcu() call done after deletion from hash list, since caller
will perform a synchronize_net() call after its ndo_stop() call.
Add a new netdev->dismantle field to signal this dismantle intent.
Reduces RTNL hold time.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's way past it's usefulness. And this gets rid of a bunch
of stray ->rt_{dst,src} references.
Even the comment documenting the macro was inaccurate (stated
default was 1 when it's 0).
If reintroduced, it should be done properly, with dynamic debug
facilities.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cool, how about we make 'Features changed' debug as well?
This way userspace can't fill up the log just by tweaking tun features
with an ioctl.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using plain hlist_del() in dev_change_name() is wrong since a
concurrent reader can crash trying to dereference LIST_POISON1.
Bug introduced in commit 72c9528bab (net: Introduce
dev_get_by_name_rcu())
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those reduced to DEBUG can possibly be triggered by unprivileged processes
and are nothing exceptional. Illegal checksum combinations can only be
caused by driver bug, so promote those messages to WARN.
Since GSO without SG will now only cause DEBUG message from
netdev_fix_features(), remove the workaround from register_netdevice().
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
We plan to remove cpu_xx() old api later. Thus this patch
convert it.
This patch has no functional change.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added code to take FW dump via ethtool. Dump level can be controlled via setting the
dump flag. A get function is provided to query the current setting of the dump flag.
Dump data is obtained from the driver via a separate get function.
Changes from v3:
Fixed buffer length issue in ethtool_get_dump_data function.
Updated kernel doc for ethtool_dump struct and get_dump_flag function.
Changes from v2:
Provided separate commands for get flag and data.
Check for minimum of the two buffer length obtained via ethtool and driver and
use that for dump buffer
Pass up the driver return error codes up to the caller.
Added kernel doc comments.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will be needed by bonding and other drivers changing vlan_features
after ndo_init callback.
As a bonus, this includes kernel-doc for netdev_update_features().
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue was introduced in commit eed2a12f1e.
Signed-off-by: Franco Fichtner <franco@lastsummer.de>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 443457242b (factorize sync-rcu call in
unregister_netdevice_many) mistakenly removed one test from dev_close()
Following actions trigger a BUG :
modprobe bonding
modprobe dummy
ifconfig bond0 up
ifenslave bond0 dummy0
rmmod dummy
dev_close() must not close a non IFF_UP device.
With help from Frank Blaschka and Einar EL Lueck
Reported-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Reported-by: Einar EL Lueck <ELELUECK@de.ibm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the new abstraction and allow network devices
to be placed in any network namespace that we have a fd to talk
about.
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Implementing file descriptors for the network namespace
is simple and straight forward.
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
mac_pton() parses MAC address in form XX:XX:XX:XX:XX:XX and only in that form.
mac_pton() doesn't dirty result until it's sure string representation is valid.
mac_pton() doesn't care about characters _after_ last octet,
it's up to caller to deal with it.
mac_pton() diverges from 0/-E return value convention.
Target usage:
if (!mac_pton(str, whatever->mac))
return -EINVAL;
/* ->mac being u8 [ETH_ALEN] is filled at this point. */
/* optionally check str[3 * ETH_ALEN - 1] for termination */
Use mac_pton() in pktgen and netconsole for start.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
veth devices dont use the batched device unregisters yet.
Since veth are a pair of devices, it makes sense to use a batch of two
unregisters, this roughly divides dismantle time by two.
Fix this by changing dellink() callers to always provide a non NULL
head. (Idea from Michał Mirosław)
This patch also handles macvlan case : We now dismantle all macvlans on
top of a lower dev at once.
Reported-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Michał Mirosław <mirqus@gmail.com>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables ethtool to set the loopback mode on a given interface.
By configuring the interface in loopback mode in conjunction with a policy
route / rule, a userland application can stress the egress / ingress path
exposing the flows of the change in progress and potentially help developer(s)
understand the impact of those changes without even sending a packet out
on the network.
Following set of commands illustrates one such example -
a) ip -4 addr add 192.168.1.1/24 dev eth1
b) ip -4 rule add from all iif eth1 lookup 250
c) ip -4 route add local 0/0 dev lo proto kernel scope host table 250
d) arp -Ds 192.168.1.100 eth1
e) arp -Ds 192.168.1.200 eth1
f) sysctl -w net.ipv4.ip_nonlocal_bind=1
g) sysctl -w net.ipv4.conf.all.accept_local=1
# Assuming that the machine has 8 cores
h) taskset 000f netserver -L 192.168.1.200
i) taskset 00f0 netperf -t TCP_CRR -L 192.168.1.100 -H 192.168.1.200 -l 30
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't know why %pI6 doesn't compress, but the format specifier is
kernel-standard, so use it.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After that all the upstream kernel drivers now use phys_id,
and the old ethtool_ops interface (phys_id) can be removed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rcu callback net_generic_release() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(net_generic_release).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu callback xps_dev_maps_release() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(xps_dev_maps_release).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu callback xps_map_release() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(xps_map_release).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu callback rps_map_release() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(rps_map_release).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu callback free_dm_hw_stat() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(free_dm_hw_stat).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu callback __gen_kill_estimator() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(__gen_kill_estimator).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu callback ha_rcu_free() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(ha_rcu_free).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Force dev_alloc_name() to be called from register_netdevice() by
dev_get_valid_name(). That allows to remove multiple explicit
dev_alloc_name() calls.
The possibility to call dev_alloc_name in advance remains.
This also fixes veth creation regresion caused by
84c49d8c3e
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ioctl() calls against a socket with an inappropriate ioctl operation
are incorrectly returning EINVAL rather than ENOTTY:
[ENOTTY]
Inappropriate I/O control operation.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=33992
Signed-off-by: Lifeng Sun <lifongsun@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four years ago, Patrick made a change to hold rtnl mutex during netlink
dump callbacks.
I believe it was a wrong move. This slows down concurrent dumps, making
good old /proc/net/ files faster than rtnetlink in some situations.
This occurred to me because one "ip link show dev ..." was _very_ slow
on a workload adding/removing network devices in background.
All dump callbacks are able to use RCU locking now, so this patch does
roughly a revert of commits :
1c2d670f36 : [RTNETLINK]: Hold rtnl_mutex during netlink dump callbacks
6313c1e099 : [RTNETLINK]: Remove unnecessary locking in dump callbacks
This let writers fight for rtnl mutex and readers going full speed.
It also takes care of phonet : phonet_route_get() is now called from rcu
read section. I renamed it to phonet_route_get_rcu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Remi Denis-Courmont <remi.denis-courmont@nokia.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).
This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.
All drivers visible to make allyesconfig under x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pktgen doesn't generate number of frags requested.
Divide packet size by number of frags and fill that in every frags.
Example:
With packet size 1470, it generate only 11 frags. Initial frags
get lenght 706, 353, 177....so on. Last frag get divided by 2.
Now with this fix, each frags will get 78 bytes.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make dst_alloc() and it's users explicitly initialize the entire
entry.
The zero'ing done by kmem_cache_zalloc() was almost entirely
redundant.
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify and fix netdev_increment_features() to conform to what is
stated in netdevice.h comments about NETIF_F_ONE_FOR_ALL.
Include FCoE segmentation and VLAN-challedged flags in computation.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since now when bonding uses rx_handler, all traffic going into bond
device goes thru bond_handle_frame. So there's no need to go back into
bonding code later via ptype handlers. This patch converts
original ptype handlers into "bonding receive probes". These functions
are called from bond_handle_frame and they are registered per-mode.
Note that vlan packets are also handled because they are always untagged
thanks to vlan_untag()
Note that this also allows arpmon for eth-bond-bridge-vlan topology.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__ethtool_set_flags() was not taking into account features set but not
user-toggleable.
Since GFLAGS returns masked dev->features, EINVAL is returned when
passed flags differ to it, and not to wanted_features.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inline a small static function that's only ever called from one place.
Signed-off-by: Rob Landley <rlandley@parallels.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When physical identification of an adapter is done by toggling the
mechanism on and off through software utilizing the set_phys_id operation,
it is done with a fixed duration for both on and off states. Some drivers
may want to set a custom duration for the on/off intervals. This patch
changes the API so the return code from the driver's entry point when it
is called with ETHTOOL_ID_ACTIVE can specify the frequency at which to
cycle the on/off states, and updates the drivers that have already been
converted to use the new set_phys_id and use the synchronous method for
identifying an adapter.
The physical identification frequency set in the updated drivers is based
on how it was done prior to the introduction of set_phys_id.
Compile tested only. Also fixes a compiler warning in sfc.
v2: drivers do not return -EINVAL for ETHOOL_ID_ACTIVE
v3: fold patchset into single patch and cleanup per Ben's feedback
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: Don Fry <pcnet32@frontier.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Steve Hodgson <shodgson@solarflare.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool support to configure RX, TX and other channels. combined field
in struct ethtool_channels to reflect set of channel (RX, TX or other).
Other channel can be link interrupts, SR-IOV coordination etc.
ETHTOOL_GCHANNELS will report max and current number of RX channels,
max and current number of TX channels, max and current number of other channel
or max and current number of combined channel.
Number of channel can be modify upto max number of channel through
ETHTOOL_SCHANNELS command.
Ben Hutchings:
o define 'combined' and 'other' types. Most multiqueue drivers pair up RX and TX
queues so that most channels combine RX and TX work.
o Please could you use a kernel-doc comment to describe the structure.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_TSO_ECN has no effect when TSO is disabled; this just means
that feature state will be accurately reported to user-space.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The feature flags NETIF_F_TSO and NETIF_F_TSO6 independently enable
TSO for IPv4 and IPv6 respectively. However, the test in
netdev_fix_features() and its predecessor functions was never updated
to check for NETIF_F_TSO6, possibly because it was originally proposed
that TSO for IPv6 would be dependent on both feature flags.
Now that these feature flags can be changed independently from
user-space and we depend on netdev_fix_features() to fix invalid
feature combinations, it's important to disable them both if
scatter-gather is disabled. Also disable NETIF_F_TSO_ECN so
user-space sees all TSO features as disabled.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now there are 2 paths for rx vlan frames. When rx-vlan-hw-accel is
enabled, skb is untagged by NIC, vlan_tci is set and the skb gets into
vlan code in __netif_receive_skb - vlan_hwaccel_do_receive.
For non-rx-vlan-hw-accel however, tagged skb goes thru whole
__netif_receive_skb, it's untagged in ptype_base hander and reinjected
This incosistency is fixed by this patch. Vlan untagging happens early in
__netif_receive_skb so the rest of code (ptype_all handlers, rx_handlers)
see the skb like it was untagged by hw.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v1->v2:
remove "inline" from vlan_core.c functions
Signed-off-by: David S. Miller <davem@davemloft.net>
When blinking for a duration set by the user, the value specified is in
seconds but it is used as the number of jiffies in the timeout after which
the Physical ID indicator is deactivated. Fix by converting the timeout
to seconds.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to prevent a possible null pointer dereference if
NETIF_F_NTUPLE is defined but the set_rx_ntuple function pointer is not.
The main motivation behind this patch is to eventually replace the ntuple
interfaces entirely with the network flow classifier interfaces. This
allows the device drivers to maintain the ntuple check internally while
using the network flow classifier interface for setting up and displaying
rules.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool ETHTOOL_PHYS_ID command runs for an arbitrarily long
period of time, holding the RTNL lock. This blocks routing updates,
device enumeration, and various important operations that one might
want to keep running while hunting for the flashing LED.
We need to drop the RTNL lock during this operation, but currently the
core implementation is a thin wrapper around a driver operation and
drivers may well depend upon holding the lock.
Define a new driver operation 'set_phys_id' with an argument that sets
the ID indicator on/off/inactive/active (the last optional, for any
driver or firmware that prefers to handle blinking asynchronously).
When this is defined, the ethtool core drops the lock while waiting
and only acquires it around calls to this operation.
Deprecate the 'phys_id' operation in favour of this. It can be
removed once all in-tree drivers are converted.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This patch uses __copy_from_user_nocache on transmit to bypass data
cache for a performance improvement. skb_add_data_nocache and
skb_copy_to_page_nocache can be called by sendmsg functions to use
this feature, initial support is in tcp_sendmsg. This functionality is
configurable per device using ethtool.
Presumably, this feature would only be useful when the driver does
not touch the data. The feature is turned on by default if a device
indicates that it does some form of checksum offload; it is off by
default for devices that do no checksum offload or indicate no checksum
is necessary. For the former case copy-checksum is probably done
anyway, in the latter case the device is likely loopback in which case
the no cache copy is probably not beneficial.
This patch was tested using 200 instances of netperf TCP_RR with
1400 byte request and one byte reply. Platform is 16 core AMD x86.
No-cache copy disabled:
672703 tps, 97.13% utilization
50/90/99% latency:244.31 484.205 1028.41
No-cache copy enabled:
702113 tps, 96.16% utilization,
50/90/99% latency 238.56 467.56 956.955
Using 14000 byte request and response sizes demonstrate the
effects more dramatically:
No-cache copy disabled:
79571 tps, 34.34 %utlization
50/90/95% latency 1584.46 2319.59 5001.76
No-cache copy enabled:
83856 tps, 34.81% utilization
50/90/95% latency 2508.42 2622.62 2735.88
Note especially the effect on latency tail (95th percentile).
This seems to provide a nice performance improvement and is
consistent in the tests I ran. Presumably, this would provide
the greatest benfits in the presence of an application workload
stressing the cache and a lot of transmit data happening.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue FEAT_CHANGE notification when features are changed by
netdev_update_features(). This will allow changes made by extra constraints
on e.g. MTU change to be properly propagated like changes via ethtool.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the device where is coming from the packet has TSO enabled,
we should not check the mtu size value as this one could be bigger
than the expected value.
This is the case for the macvlan driver when the lower device has
TSO enabled. The macvlan inherit this feature and forward the packets
without fragmenting them. Then the packets go through dev_forward_skb
and are dropped. This patch fix this by checking TSO is not enabled
when we want to check the mtu size.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
xfrm: Restrict extended sequence numbers to esp
xfrm: Check for esn buffer len in xfrm_new_ae
xfrm: Assign esn pointers when cloning a state
xfrm: Move the test on replay window size into the replay check functions
netdev: bfin_mac: document TE setting in RMII modes
drivers net: Fix declaration ordering in inline functions.
cxgb3: Apply interrupt coalescing settings to all queues
net: Always allocate at least 16 skb frags regardless of page size
ipv4: Don't ip_rt_put() an error pointer in RAW sockets.
net: fix ethtool->set_flags not intended -EINVAL return value
mlx4_en: Fix loss of promiscuity
tg3: Fix inline keyword usage
tg3: use <linux/io.h> and <linux/uaccess.h> instead <asm/io.h> and <asm/uaccess.h>
net: use CHECKSUM_NONE instead of magic number
Net / jme: Do not use legacy PCI power management
myri10ge: small rx_done refactoring
bridge: notify applications if address of bridge device changes
ipv4: Fix IP timestamp option (IPOPT_TS_PRESPEC) handling in ip_options_echo()
can: c_can: Fix tx_bytes accounting
can: c_can_platform: fix irq check in probe
...
After commit d5dbda2380 "ethtool: Add
support for vlan accleration.", drivers that have NETIF_F_HW_VLAN_TX,
and/or NETIF_F_HW_VLAN_RX feature, but do not allow enable/disable vlan
acceleration via ethtool set_flags, always return -EINVAL from that
function. Fix by returning -EINVAL only if requested features do not
match current settings and can not be changed by driver.
Change any driver that define ethtool->set_flags to use
ethtool_invalid_flags() to avoid similar problems in the future
(also on drivers that do not have the problem).
Tested with modified (to reproduce this bug) myri10ge driver.
Cc: stable@kernel.org # 2.6.37+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac address of the bridge device may be changed when a new interface
is added to the bridge. If this happens, then the bridge needs to call
the network notifiers to tickle any other systems that care. Since bridge
can be a module, this also means exporting the notifier function.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code itself can explain what it is doing, no need these comments.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
route: Take the right src and dst addresses in ip_route_newports
ipv4: Fix nexthop caching wrt. scoping.
ipv4: Invalidate nexthop cache nh_saddr more correctly.
net: fix pch_gbe section mismatch warning
ipv4: fix fib metrics
mlx4_en: Removing HW info from ethtool -i report.
net_sched: fix THROTTLED/RUNNING race
drivers/net/a2065.c: Convert release_resource to release_region/release_mem_region
drivers/net/ariadne.c: Convert release_resource to release_region/release_mem_region
bonding: fix rx_handler locking
myri10ge: fix rmmod crash
mlx4_en: updated driver version to 1.5.4.1
mlx4_en: Using blue flame support
mlx4_core: reserve UARs for userspace consumers
mlx4_core: maintain available field in bitmap allocator
mlx4: Add blue flame support for kernel consumers
mlx4_en: Enabling new steering
mlx4: Add support for promiscuous mode in the new steering model.
mlx4: generalization of multicast steering.
mlx4_en: Reporting HW revision in ethtool -i
...
ksoftirqd, kworker, migration, and pktgend kthreads can be created with
kthread_create_on_node(), to get proper NUMA affinities for their stack and
task_struct.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement compatibility with new hw_features for dev_disable_lro().
This is a transition path - dev_disable_lro() should be later
integrated into netdev_fix_features() after all drivers are converted.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out to me recently that my spelling could be better :)
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__ethtool_set_sg does not check if dev->ethtool_ops->set_sg is defined
which can result in a NULL pointer dereference when ethtool is used to
change SG settings for drivers without SG support.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1480 commits)
bonding: enable netpoll without checking link status
xfrm: Refcount destination entry on xfrm_lookup
net: introduce rx_handler results and logic around that
bonding: get rid of IFF_SLAVE_INACTIVE netdev->priv_flag
bonding: wrap slave state work
net: get rid of multiple bond-related netdevice->priv_flags
bonding: register slave pointer for rx_handler
be2net: Bump up the version number
be2net: Copyright notice change. Update to Emulex instead of ServerEngines
e1000e: fix kconfig for crc32 dependency
netfilter ebtables: fix xt_AUDIT to work with ebtables
xen network backend driver
bonding: Improve syslog message at device creation time
bonding: Call netif_carrier_off after register_netdevice
bonding: Incorrect TX queue offset
net_sched: fix ip_tos2prio
xfrm: fix __xfrm_route_forward()
be2net: Fix UDP packet detected status in RX compl
Phonet: fix aligned-mode pipe socket buffer header reserve
netxen: support for GbE port settings
...
Fix up conflicts in drivers/staging/brcm80211/brcmsmac/wl_mac80211.c
with the staging updates.
This patch allows rx_handlers to better signalize what to do next to
it's caller. That makes skb->deliver_no_wcard no longer needed.
kernel-doc for rx_handler_result is taken from Nicolas' patch.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (57 commits)
tidy the trailing symlinks traversal up
Turn resolution of trailing symlinks iterative everywhere
simplify link_path_walk() tail
Make trailing symlink resolution in path_lookupat() iterative
update nd->inode in __do_follow_link() instead of after do_follow_link()
pull handling of one pathname component into a helper
fs: allow AT_EMPTY_PATH in linkat(), limit that to CAP_DAC_READ_SEARCH
Allow passing O_PATH descriptors via SCM_RIGHTS datagrams
readlinkat(), fchownat() and fstatat() with empty relative pathnames
Allow O_PATH for symlinks
New kind of open files - "location only".
ext4: Copy fs UUID to superblock
ext3: Copy fs UUID to superblock.
vfs: Export file system uuid via /proc/<pid>/mountinfo
unistd.h: Add new syscalls numbers to asm-generic
x86: Add new syscalls for x86_64
x86: Add new syscalls for x86_32
fs: Remove i_nlink check from file system link callback
fs: Don't allow to create hardlink for deleted file
vfs: Add open by file handle support
...
Just need to make sure that AF_UNIX garbage collector won't
confuse O_PATHed socket on filesystem for real AF_UNIX opened
socket.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
(bug introduced by commit 26ad787962
(pktgen: speedup fragmented skbs)
The headers of pktgen were incorrectly added in a pktgen packet
without frags (frags=0). There was an offset in the pktgen headers.
The cause was in reusing the pgh variable as a return variable in skb_put
when adding the payload to the skb.
Signed-off-by: Daniel Turull <daniel.turull@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
I intend to turn struct flowi into a union of AF specific flowi
structs. There will be a common structure that each variant includes
first, much like struct sock_common.
This is the first step to move in that direction.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since a8f80e8ff9 any process with
CAP_NET_ADMIN may load any module from /lib/modules/. This doesn't mean
that CAP_NET_ADMIN is a superset of CAP_SYS_MODULE as modules are
limited to /lib/modules/**. However, CAP_NET_ADMIN capability shouldn't
allow anybody load any module not related to networking.
This patch restricts an ability of autoloading modules to netdev modules
with explicit aliases. This fixes CVE-2011-1019.
Arnd Bergmann suggested to leave untouched the old pre-v2.6.32 behavior
of loading netdev modules by name (without any prefix) for processes
with CAP_SYS_MODULE to maintain the compatibility with network scripts
that use autoloading netdev modules by aliases like "eth0", "wlan0".
Currently there are only three users of the feature in the upstream
kernel: ipip, ip_gre and sit.
root@albatros:~# capsh --drop=$(seq -s, 0 11),$(seq -s, 13 34) --
root@albatros:~# grep Cap /proc/$$/status
CapInh: 0000000000000000
CapPrm: fffffff800001000
CapEff: fffffff800001000
CapBnd: fffffff800001000
root@albatros:~# modprobe xfs
FATAL: Error inserting xfs
(/lib/modules/2.6.38-rc6-00001-g2bf4ca3/kernel/fs/xfs/xfs.ko): Operation not permitted
root@albatros:~# lsmod | grep xfs
root@albatros:~# ifconfig xfs
xfs: error fetching interface information: Device not found
root@albatros:~# lsmod | grep xfs
root@albatros:~# lsmod | grep sit
root@albatros:~# ifconfig sit
sit: error fetching interface information: Device not found
root@albatros:~# lsmod | grep sit
root@albatros:~# ifconfig sit0
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
root@albatros:~# lsmod | grep sit
sit 10457 0
tunnel4 2957 1 sit
For CAP_SYS_MODULE module loading is still relaxed:
root@albatros:~# grep Cap /proc/$$/status
CapInh: 0000000000000000
CapPrm: ffffffffffffffff
CapEff: ffffffffffffffff
CapBnd: ffffffffffffffff
root@albatros:~# ifconfig xfs
xfs: error fetching interface information: Device not found
root@albatros:~# lsmod | grep xfs
xfs 745319 0
Reference: https://lkml.org/lkml/2011/2/24/203
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
The units in show_results in pktgen were not correct.
The results are in usec but it was displayed nsec.
Reported-by: Jong-won Lee <ljw@handong.edu>
Signed-off-by: Daniel Turull <daniel.turull@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was there before, I forgot about this. Allows deliveries to
ptype_base handlers registered for orig_dev. I presume this is still
desired.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
UFO doesn't really use the sk_sndmsg_* parameters so touching
them is pointless. It can't use them anyway since the whole
point of UFO is to use the original pages without copying.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil pointed out that we can't send ARP reply on behalf of slaves,
we need to move the arp queue to their bond device.
Signed-off-by: WANG Cong <amwang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
V4: rebase to net-next-2.6
This patch removes the flag IFF_IN_NETPOLL, we don't need it any more since
we have netpoll_tx_running() now.
Signed-off-by: WANG Cong <amwang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
addr_type of 0 means that the type should be adopted from from_dev and
not from __hw_addr_del_multiple(). Unfortunately it isn't so and
addr_type will always be considered. Fix this by implementing the
considered and documented behavior.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use discrete setting ops for not updated drivers. This will not make
them conform to full G/SFEATURES semantics, though.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement getting rx checksum state for not updated drivers.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid "Features changed" message and ndo_set_features call on device
registration caused by automatic enabling of GSO and GRO. Driver should
have enabled hardware offloads it set in features, so the ndo_set_features()
is not needed at registration time.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix netdev_update_features() messages on register time by moving
the call further in register_netdevice(). When
netdev->reg_state != NETREG_REGISTERED, netdev_name() returns
"(unregistered netdevice)" even if the dev's name is already filled.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 9b5e383c11 (net: Introduce
unregister_netdevice_many()) left an active LIST_HEAD() in
rollback_registered(), with possible memory corruption.
Even if device is freed without touching its unreg_list (and therefore
touching the previous memory location holding LISTE_HEAD(single), better
close the bug for good, since its really subtle.
(Same fix for default_device_exit_batch() for completeness)
Reported-by: Michal Hocko <mhocko@suse.cz>
Tested-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Eric W. Biderman <ebiderman@xmission.com>
Tested-by: Eric W. Biderman <ebiderman@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Octavian Purdila <opurdila@ixiacom.com>
CC: stable <stable@kernel.org> [.33+]
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biderman and Michal Hocko reported various memory corruptions
that we suspected to be related to a LIST head located on stack, that
was manipulated after thread left function frame (and eventually exited,
so its stack was freed and reused).
Eric Dumazet suggested the problem was probably coming from commit
443457242b (net: factorize
sync-rcu call in unregister_netdevice_many)
This patch fixes __dev_close() and dev_close() to properly deinit their
respective LIST_HEAD(single) before exiting.
References: https://lkml.org/lkml/2011/2/16/304
References: https://lkml.org/lkml/2011/2/14/223
Reported-by: Michal Hocko <mhocko@suse.cz>
Tested-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Eric W. Biderman <ebiderman@xmission.com>
Tested-by: Eric W. Biderman <ebiderman@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows avoiding multiple writes to the initial __refcnt.
The most simplest cases of wanting an initial reference of "1"
in ipv4 and ipv6 have been converted, the rest have been left
along and kept at the existing "0".
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce NETIF_F_RXCSUM to replace device-private flags for RX checksum
offload. Integrate it with ndo_fix_features.
ethtool_op_get_rx_csum() is removed altogether as nothing in-tree uses it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a new framework to handle device features setting.
It consists of:
- new fields in struct net_device:
+ hw_features - features that hw/driver supports toggling
+ wanted_features - features that user wants enabled, when possible
- new netdev_ops:
+ feat = ndo_fix_features(dev, feat) - API checking constraints for
enabling features or their combinations
+ ndo_set_features(dev) - API updating hardware state to match
changed dev->features
- new ethtool commands:
+ ETHTOOL_GFEATURES/ETHTOOL_SFEATURES: get/set dev->wanted_features
and trigger device reconfiguration if resulting dev->features
changed
+ ETHTOOL_GSTRINGS(ETH_SS_FEATURES): get feature bits names (meaning)
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to enable GRO even if RX csum is disabled. GRO will not
be used for packets without hardware checksum anyway.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed for unified offloads patch.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
For testing and debugging purposes it is useful to be able to disable
hardware acceleration of RFS without disabling RFS altogether. Since
this is a similar feature to 'n-tuple' flow steering through the
ethtool API, test the same feature flag that controls that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
If the root qdisc for a net device is mqprio, and the driver's
ndo_setup_tc() operation dynamically adds and remvoes TX queues,
netif_set_real_num_tx_queues() will be called during device
unregistration to remove the extra TX queues when the qdisc is
destroyed. Currently this causes the corresponding kobjects
to be leaked, and the device's reference count never drops to 0.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This patch allows userspace to enslave/release slave devices via netlink
interface using IFLA_MASTER. This introduces generic way to add/remove
underling devices.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->master is now tightly connected to bonding driver. This patch makes
this pointer more general and ready to be used by others.
- netdev_set_master() - bond specifics moved to new function
netdev_set_bond_master()
- introduced netif_is_bond_slave() to check if device is a bonding slave
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to check (master) twice and to drive in and out the header file.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a512b92 adds sysfs entry for net device group, but
before this commit, tun also uses group sysfs, so after this
commit checkin, kernel warns like this:
sysfs: cannot create duplicate filename '/devices/virtual/net/vnet0/group'
Since tun has used this for years, rename sysfs under tun might
break existing userspace, so rename group sysfs entry for net device
group is a better choice.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
