diff --git a/drivers/net/mipsnet.c b/drivers/net/mipsnet.c index aafc3ce59cbb..6d343efb2717 100644 --- a/drivers/net/mipsnet.c +++ b/drivers/net/mipsnet.c @@ -4,8 +4,6 @@ * for more details. */ -#define DEBUG - #include #include #include @@ -15,11 +13,93 @@ #include #include -#include "mipsnet.h" /* actual device IO mapping */ +#define MIPSNET_VERSION "2007-11-17" -#define MIPSNET_VERSION "2005-06-20" +/* + * Net status/control block as seen by sw in the core. + */ +struct mipsnet_regs { + /* + * Device info for probing, reads as MIPSNET%d where %d is some + * form of version. + */ + u64 devId; /*0x00 */ -#define mipsnet_reg_address(dev, field) (dev->base_addr + field_offset(field)) + /* + * read only busy flag. + * Set and cleared by the Net Device to indicate that an rx or a tx + * is in progress. + */ + u32 busy; /*0x08 */ + + /* + * Set by the Net Device. + * The device will set it once data has been received. + * The value is the number of bytes that should be read from + * rxDataBuffer. The value will decrease till 0 until all the data + * from rxDataBuffer has been read. + */ + u32 rxDataCount; /*0x0c */ +#define MIPSNET_MAX_RXTX_DATACOUNT (1 << 16) + + /* + * Settable from the MIPS core, cleared by the Net Device. + * The core should set the number of bytes it wants to send, + * then it should write those bytes of data to txDataBuffer. + * The device will clear txDataCount has been processed (not + * necessarily sent). + */ + u32 txDataCount; /*0x10 */ + + /* + * Interrupt control + * + * Used to clear the interrupted generated by this dev. + * Write a 1 to clear the interrupt. (except bit31). + * + * Bit0 is set if it was a tx-done interrupt. + * Bit1 is set when new rx-data is available. + * Until this bit is cleared there will be no other RXs. + * + * Bit31 is used for testing, it clears after a read. + * Writing 1 to this bit will cause an interrupt to be generated. + * To clear the test interrupt, write 0 to this register. + */ + u32 interruptControl; /*0x14 */ +#define MIPSNET_INTCTL_TXDONE (1u << 0) +#define MIPSNET_INTCTL_RXDONE (1u << 1) +#define MIPSNET_INTCTL_TESTBIT (1u << 31) + + /* + * Readonly core-specific interrupt info for the device to signal + * the core. The meaning of the contents of this field might change. + */ + /* XXX: the whole memIntf interrupt scheme is messy: the device + * should have no control what so ever of what VPE/register set is + * being used. + * The MemIntf should only expose interrupt lines, and something in + * the config should be responsible for the line<->core/vpe bindings. + */ + u32 interruptInfo; /*0x18 */ + + /* + * This is where the received data is read out. + * There is more data to read until rxDataReady is 0. + * Only 1 byte at this regs offset is used. + */ + u32 rxDataBuffer; /*0x1c */ + + /* + * This is where the data to transmit is written. + * Data should be written for the amount specified in the + * txDataCount register. + * Only 1 byte at this regs offset is used. + */ + u32 txDataBuffer; /*0x20 */ +}; + +#define regaddr(dev, field) \ + (dev->base_addr + offsetof(struct mipsnet_regs, field)) static char mipsnet_string[] = "mipsnet"; @@ -29,32 +109,27 @@ static char mipsnet_string[] = "mipsnet"; static int ioiocpy_frommipsnet(struct net_device *dev, unsigned char *kdata, int len) { - uint32_t available_len = inl(mipsnet_reg_address(dev, rxDataCount)); - - if (available_len < len) - return -EFAULT; - for (; len > 0; len--, kdata++) - *kdata = inb(mipsnet_reg_address(dev, rxDataBuffer)); + *kdata = inb(regaddr(dev, rxDataBuffer)); - return inl(mipsnet_reg_address(dev, rxDataCount)); + return inl(regaddr(dev, rxDataCount)); } -static inline ssize_t mipsnet_put_todevice(struct net_device *dev, +static inline void mipsnet_put_todevice(struct net_device *dev, struct sk_buff *skb) { int count_to_go = skb->len; char *buf_ptr = skb->data; - outl(skb->len, mipsnet_reg_address(dev, txDataCount)); + outl(skb->len, regaddr(dev, txDataCount)); for (; count_to_go; buf_ptr++, count_to_go--) - outb(*buf_ptr, mipsnet_reg_address(dev, txDataBuffer)); + outb(*buf_ptr, regaddr(dev, txDataBuffer)); dev->stats.tx_packets++; dev->stats.tx_bytes += skb->len; - return skb->len; + dev_kfree_skb(skb); } static int mipsnet_xmit(struct sk_buff *skb, struct net_device *dev) @@ -69,18 +144,20 @@ static int mipsnet_xmit(struct sk_buff *skb, struct net_device *dev) return 0; } -static inline ssize_t mipsnet_get_fromdev(struct net_device *dev, size_t count) +static inline ssize_t mipsnet_get_fromdev(struct net_device *dev, size_t len) { struct sk_buff *skb; - size_t len = count; - skb = alloc_skb(len + 2, GFP_KERNEL); + if (!len) + return len; + + skb = dev_alloc_skb(len + NET_IP_ALIGN); if (!skb) { dev->stats.rx_dropped++; return -ENOMEM; } - skb_reserve(skb, 2); + skb_reserve(skb, NET_IP_ALIGN); if (ioiocpy_frommipsnet(dev, skb_put(skb, len), len)) return -EFAULT; @@ -92,50 +169,42 @@ static inline ssize_t mipsnet_get_fromdev(struct net_device *dev, size_t count) dev->stats.rx_packets++; dev->stats.rx_bytes += len; - return count; + return len; } static irqreturn_t mipsnet_interrupt(int irq, void *dev_id) { struct net_device *dev = dev_id; + u32 int_flags; + irqreturn_t ret = IRQ_NONE; - irqreturn_t retval = IRQ_NONE; - uint64_t interruptFlags; + if (irq != dev->irq) + goto out_badirq; - if (irq == dev->irq) { - retval = IRQ_HANDLED; - - interruptFlags = - inl(mipsnet_reg_address(dev, interruptControl)); - - if (interruptFlags & MIPSNET_INTCTL_TXDONE) { - outl(MIPSNET_INTCTL_TXDONE, - mipsnet_reg_address(dev, interruptControl)); - /* only one packet at a time, we are done. */ - netif_wake_queue(dev); - } else if (interruptFlags & MIPSNET_INTCTL_RXDONE) { - mipsnet_get_fromdev(dev, - inl(mipsnet_reg_address(dev, rxDataCount))); - outl(MIPSNET_INTCTL_RXDONE, - mipsnet_reg_address(dev, interruptControl)); - - } else if (interruptFlags & MIPSNET_INTCTL_TESTBIT) { - /* - * TESTBIT is cleared on read. - * And takes effect after a write with 0 - */ - outl(0, mipsnet_reg_address(dev, interruptControl)); - } else { - /* Maybe shared IRQ, just ignore, no clearing. */ - retval = IRQ_NONE; - } - - } else { - printk(KERN_INFO "%s: %s(): irq %d for unknown device\n", - dev->name, __FUNCTION__, irq); - retval = IRQ_NONE; + /* TESTBIT is cleared on read. */ + int_flags = inl(regaddr(dev, interruptControl)); + if (int_flags & MIPSNET_INTCTL_TESTBIT) { + /* TESTBIT takes effect after a write with 0. */ + outl(0, regaddr(dev, interruptControl)); + ret = IRQ_HANDLED; + } else if (int_flags & MIPSNET_INTCTL_TXDONE) { + /* Only one packet at a time, we are done. */ + dev->stats.tx_packets++; + netif_wake_queue(dev); + outl(MIPSNET_INTCTL_TXDONE, + regaddr(dev, interruptControl)); + ret = IRQ_HANDLED; + } else if (int_flags & MIPSNET_INTCTL_RXDONE) { + mipsnet_get_fromdev(dev, inl(regaddr(dev, rxDataCount))); + outl(MIPSNET_INTCTL_RXDONE, regaddr(dev, interruptControl)); + ret = IRQ_HANDLED; } - return retval; + return ret; + +out_badirq: + printk(KERN_INFO "%s: %s(): irq %d for unknown device\n", + dev->name, __FUNCTION__, irq); + return ret; } static int mipsnet_open(struct net_device *dev) @@ -144,18 +213,15 @@ static int mipsnet_open(struct net_device *dev) err = request_irq(dev->irq, &mipsnet_interrupt, IRQF_SHARED, dev->name, (void *) dev); - if (err) { - release_region(dev->base_addr, MIPSNET_IO_EXTENT); + release_region(dev->base_addr, sizeof(struct mipsnet_regs)); return err; } netif_start_queue(dev); /* test interrupt handler */ - outl(MIPSNET_INTCTL_TESTBIT, - mipsnet_reg_address(dev, interruptControl)); - + outl(MIPSNET_INTCTL_TESTBIT, regaddr(dev, interruptControl)); return 0; } @@ -163,7 +229,7 @@ static int mipsnet_open(struct net_device *dev) static int mipsnet_close(struct net_device *dev) { netif_stop_queue(dev); - + free_irq(dev->irq, dev); return 0; } @@ -194,10 +260,11 @@ static int __init mipsnet_probe(struct device *dev) */ netdev->base_addr = 0x4200; netdev->irq = MIPS_CPU_IRQ_BASE + MIPSCPU_INT_MB0 + - inl(mipsnet_reg_address(netdev, interruptInfo)); + inl(regaddr(netdev, interruptInfo)); /* Get the io region now, get irq on open() */ - if (!request_region(netdev->base_addr, MIPSNET_IO_EXTENT, "mipsnet")) { + if (!request_region(netdev->base_addr, sizeof(struct mipsnet_regs), + "mipsnet")) { err = -EBUSY; goto out_free_netdev; } @@ -217,7 +284,7 @@ static int __init mipsnet_probe(struct device *dev) return 0; out_free_region: - release_region(netdev->base_addr, MIPSNET_IO_EXTENT); + release_region(netdev->base_addr, sizeof(struct mipsnet_regs)); out_free_netdev: free_netdev(netdev); @@ -231,7 +298,7 @@ static int __devexit mipsnet_device_remove(struct device *device) struct net_device *dev = dev_get_drvdata(device); unregister_netdev(dev); - release_region(dev->base_addr, MIPSNET_IO_EXTENT); + release_region(dev->base_addr, sizeof(struct mipsnet_regs)); free_netdev(dev); dev_set_drvdata(device, NULL); diff --git a/drivers/net/mipsnet.h b/drivers/net/mipsnet.h deleted file mode 100644 index 0132c6714a40..000000000000 --- a/drivers/net/mipsnet.h +++ /dev/null @@ -1,112 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - */ -#ifndef __MIPSNET_H -#define __MIPSNET_H - -/* - * Id of this Net device, as seen by the core. - */ -#define MIPS_NET_DEV_ID ((uint64_t) \ - ((uint64_t) 'M' << 0)| \ - ((uint64_t) 'I' << 8)| \ - ((uint64_t) 'P' << 16)| \ - ((uint64_t) 'S' << 24)| \ - ((uint64_t) 'N' << 32)| \ - ((uint64_t) 'E' << 40)| \ - ((uint64_t) 'T' << 48)| \ - ((uint64_t) '0' << 56)) - -/* - * Net status/control block as seen by sw in the core. - * (Why not use bit fields? can't be bothered with cross-platform struct - * packing.) - */ -struct net_control_block { - /* - * dev info for probing - * reads as MIPSNET%d where %d is some form of version - */ - uint64_t devId; /* 0x00 */ - - /* - * read only busy flag. - * Set and cleared by the Net Device to indicate that an rx or a tx - * is in progress. - */ - uint32_t busy; /* 0x08 */ - - /* - * Set by the Net Device. - * The device will set it once data has been received. - * The value is the number of bytes that should be read from - * rxDataBuffer. The value will decrease till 0 until all the data - * from rxDataBuffer has been read. - */ - uint32_t rxDataCount; /* 0x0c */ -#define MIPSNET_MAX_RXTX_DATACOUNT (1<<16) - - /* - * Settable from the MIPS core, cleared by the Net Device. The core - * should set the number of bytes it wants to send, then it should - * write those bytes of data to txDataBuffer. The device will clear - * txDataCount has been processed (not necessarily sent). - */ - uint32_t txDataCount; /* 0x10 */ - - /* - * Interrupt control - * - * Used to clear the interrupted generated by this dev. - * Write a 1 to clear the interrupt. (except bit31). - * - * Bit0 is set if it was a tx-done interrupt. - * Bit1 is set when new rx-data is available. - * Until this bit is cleared there will be no other RXs. - * - * Bit31 is used for testing, it clears after a read. - * Writing 1 to this bit will cause an interrupt to be generated. - * To clear the test interrupt, write 0 to this register. - */ - uint32_t interruptControl; /*0x14 */ -#define MIPSNET_INTCTL_TXDONE ((uint32_t)(1 << 0)) -#define MIPSNET_INTCTL_RXDONE ((uint32_t)(1 << 1)) -#define MIPSNET_INTCTL_TESTBIT ((uint32_t)(1 << 31)) -#define MIPSNET_INTCTL_ALLSOURCES (MIPSNET_INTCTL_TXDONE | \ - MIPSNET_INTCTL_RXDONE | \ - MIPSNET_INTCTL_TESTBIT) - - /* - * Readonly core-specific interrupt info for the device to signal the - * core. The meaning of the contents of this field might change. - * - * TODO: the whole memIntf interrupt scheme is messy: the device should - * have no control what so ever of what VPE/register set is being - * used. The MemIntf should only expose interrupt lines, and - * something in the config should be responsible for the - * line<->core/vpe bindings. - */ - uint32_t interruptInfo; /* 0x18 */ - - /* - * This is where the received data is read out. - * There is more data to read until rxDataReady is 0. - * Only 1 byte at this regs offset is used. - */ - uint32_t rxDataBuffer; /* 0x1c */ - - /* - * This is where the data to transmit is written. Data should be - * written for the amount specified in the txDataCount register. Only - * 1 byte at this regs offset is used. - */ - uint32_t txDataBuffer; /* 0x20 */ -}; - -#define MIPSNET_IO_EXTENT 0x40 /* being generous */ - -#define field_offset(field) (offsetof(struct net_control_block, field)) - -#endif /* __MIPSNET_H */