i2c/chips: Remove deprecated pca9539 driver
The pca9539 driver in drivers/i2c/chips which just exports its registers to sysfs is superseded by drivers/gpio/pca953x.c which properly uses the gpiolib. As this driver has been deprecated for more than a year, finally remove it. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Ben Gardner <gardner.ben@gmail.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
This commit is contained in:
Wolfram Sang
Jean Delvare
parent
8f67eeb0b4
commit
732d481127
4 changed files with 0 additions and 224 deletions
|
|
@ -1,58 +0,0 @@
|
|||
Kernel driver pca9539
|
||||
=====================
|
||||
|
||||
NOTE: this driver is deprecated and will be dropped soon, use
|
||||
drivers/gpio/pca9539.c instead.
|
||||
|
||||
Supported chips:
|
||||
* Philips PCA9539
|
||||
Prefix: 'pca9539'
|
||||
Addresses scanned: none
|
||||
Datasheet:
|
||||
http://www.semiconductors.philips.com/acrobat/datasheets/PCA9539_2.pdf
|
||||
|
||||
Author: Ben Gardner <bgardner@wabtec.com>
|
||||
|
||||
|
||||
Description
|
||||
-----------
|
||||
|
||||
The Philips PCA9539 is a 16 bit low power I/O device.
|
||||
All 16 lines can be individually configured as an input or output.
|
||||
The input sense can also be inverted.
|
||||
The 16 lines are split between two bytes.
|
||||
|
||||
|
||||
Detection
|
||||
---------
|
||||
|
||||
The PCA9539 is difficult to detect and not commonly found in PC machines,
|
||||
so you have to pass the I2C bus and address of the installed PCA9539
|
||||
devices explicitly to the driver at load time via the force=... parameter.
|
||||
|
||||
|
||||
Sysfs entries
|
||||
-------------
|
||||
|
||||
Each is a byte that maps to the 8 I/O bits.
|
||||
A '0' suffix is for bits 0-7, while '1' is for bits 8-15.
|
||||
|
||||
input[01] - read the current value
|
||||
output[01] - sets the output value
|
||||
direction[01] - direction of each bit: 1=input, 0=output
|
||||
invert[01] - toggle the input bit sense
|
||||
|
||||
input reads the actual state of the line and is always available.
|
||||
The direction defaults to input for all channels.
|
||||
|
||||
|
||||
General Remarks
|
||||
---------------
|
||||
|
||||
Note that each output, direction, and invert entry controls 8 lines.
|
||||
You should use the read, modify, write sequence.
|
||||
For example. to set output bit 0 of 1.
|
||||
val=$(cat output0)
|
||||
val=$(( $val | 1 ))
|
||||
echo $val > output0
|
||||
|
||||
|
|
@ -33,19 +33,6 @@ config SENSORS_PCF8574
|
|||
These devices are hard to detect and rarely found on mainstream
|
||||
hardware. If unsure, say N.
|
||||
|
||||
config SENSORS_PCA9539
|
||||
tristate "Philips PCA9539 16-bit I/O port (DEPRECATED)"
|
||||
depends on EXPERIMENTAL && GPIO_PCA953X = "n"
|
||||
help
|
||||
If you say yes here you get support for the Philips PCA9539
|
||||
16-bit I/O port.
|
||||
|
||||
This driver can also be built as a module. If so, the module
|
||||
will be called pca9539.
|
||||
|
||||
This driver is deprecated and will be dropped soon. Use
|
||||
drivers/gpio/pca953x.c instead.
|
||||
|
||||
config SENSORS_TSL2550
|
||||
tristate "Taos TSL2550 ambient light sensor"
|
||||
depends on EXPERIMENTAL
|
||||
|
|
|
|||
|
|
@ -11,7 +11,6 @@
|
|||
#
|
||||
|
||||
obj-$(CONFIG_DS1682) += ds1682.o
|
||||
obj-$(CONFIG_SENSORS_PCA9539) += pca9539.o
|
||||
obj-$(CONFIG_SENSORS_PCF8574) += pcf8574.o
|
||||
obj-$(CONFIG_SENSORS_TSL2550) += tsl2550.o
|
||||
|
||||
|
|
|
|||
|
|
@ -1,152 +0,0 @@
|
|||
/*
|
||||
pca9539.c - 16-bit I/O port with interrupt and reset
|
||||
|
||||
Copyright (C) 2005 Ben Gardner <bgardner@wabtec.com>
|
||||
|
||||
This program is free software; you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation; version 2 of the License.
|
||||
*/
|
||||
|
||||
#include <linux/module.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/slab.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/hwmon-sysfs.h>
|
||||
|
||||
/* Addresses to scan: none, device is not autodetected */
|
||||
static const unsigned short normal_i2c[] = { I2C_CLIENT_END };
|
||||
|
||||
/* Insmod parameters */
|
||||
I2C_CLIENT_INSMOD_1(pca9539);
|
||||
|
||||
enum pca9539_cmd
|
||||
{
|
||||
PCA9539_INPUT_0 = 0,
|
||||
PCA9539_INPUT_1 = 1,
|
||||
PCA9539_OUTPUT_0 = 2,
|
||||
PCA9539_OUTPUT_1 = 3,
|
||||
PCA9539_INVERT_0 = 4,
|
||||
PCA9539_INVERT_1 = 5,
|
||||
PCA9539_DIRECTION_0 = 6,
|
||||
PCA9539_DIRECTION_1 = 7,
|
||||
};
|
||||
|
||||
/* following are the sysfs callback functions */
|
||||
static ssize_t pca9539_show(struct device *dev, struct device_attribute *attr,
|
||||
char *buf)
|
||||
{
|
||||
struct sensor_device_attribute *psa = to_sensor_dev_attr(attr);
|
||||
struct i2c_client *client = to_i2c_client(dev);
|
||||
return sprintf(buf, "%d\n", i2c_smbus_read_byte_data(client,
|
||||
psa->index));
|
||||
}
|
||||
|
||||
static ssize_t pca9539_store(struct device *dev, struct device_attribute *attr,
|
||||
const char *buf, size_t count)
|
||||
{
|
||||
struct sensor_device_attribute *psa = to_sensor_dev_attr(attr);
|
||||
struct i2c_client *client = to_i2c_client(dev);
|
||||
unsigned long val = simple_strtoul(buf, NULL, 0);
|
||||
if (val > 0xff)
|
||||
return -EINVAL;
|
||||
i2c_smbus_write_byte_data(client, psa->index, val);
|
||||
return count;
|
||||
}
|
||||
|
||||
/* Define the device attributes */
|
||||
|
||||
#define PCA9539_ENTRY_RO(name, cmd_idx) \
|
||||
static SENSOR_DEVICE_ATTR(name, S_IRUGO, pca9539_show, NULL, cmd_idx)
|
||||
|
||||
#define PCA9539_ENTRY_RW(name, cmd_idx) \
|
||||
static SENSOR_DEVICE_ATTR(name, S_IRUGO | S_IWUSR, pca9539_show, \
|
||||
pca9539_store, cmd_idx)
|
||||
|
||||
PCA9539_ENTRY_RO(input0, PCA9539_INPUT_0);
|
||||
PCA9539_ENTRY_RO(input1, PCA9539_INPUT_1);
|
||||
PCA9539_ENTRY_RW(output0, PCA9539_OUTPUT_0);
|
||||
PCA9539_ENTRY_RW(output1, PCA9539_OUTPUT_1);
|
||||
PCA9539_ENTRY_RW(invert0, PCA9539_INVERT_0);
|
||||
PCA9539_ENTRY_RW(invert1, PCA9539_INVERT_1);
|
||||
PCA9539_ENTRY_RW(direction0, PCA9539_DIRECTION_0);
|
||||
PCA9539_ENTRY_RW(direction1, PCA9539_DIRECTION_1);
|
||||
|
||||
static struct attribute *pca9539_attributes[] = {
|
||||
&sensor_dev_attr_input0.dev_attr.attr,
|
||||
&sensor_dev_attr_input1.dev_attr.attr,
|
||||
&sensor_dev_attr_output0.dev_attr.attr,
|
||||
&sensor_dev_attr_output1.dev_attr.attr,
|
||||
&sensor_dev_attr_invert0.dev_attr.attr,
|
||||
&sensor_dev_attr_invert1.dev_attr.attr,
|
||||
&sensor_dev_attr_direction0.dev_attr.attr,
|
||||
&sensor_dev_attr_direction1.dev_attr.attr,
|
||||
NULL
|
||||
};
|
||||
|
||||
static struct attribute_group pca9539_defattr_group = {
|
||||
.attrs = pca9539_attributes,
|
||||
};
|
||||
|
||||
/* Return 0 if detection is successful, -ENODEV otherwise */
|
||||
static int pca9539_detect(struct i2c_client *client, int kind,
|
||||
struct i2c_board_info *info)
|
||||
{
|
||||
struct i2c_adapter *adapter = client->adapter;
|
||||
|
||||
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
|
||||
return -ENODEV;
|
||||
|
||||
strlcpy(info->type, "pca9539", I2C_NAME_SIZE);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int pca9539_probe(struct i2c_client *client,
|
||||
const struct i2c_device_id *id)
|
||||
{
|
||||
/* Register sysfs hooks */
|
||||
return sysfs_create_group(&client->dev.kobj,
|
||||
&pca9539_defattr_group);
|
||||
}
|
||||
|
||||
static int pca9539_remove(struct i2c_client *client)
|
||||
{
|
||||
sysfs_remove_group(&client->dev.kobj, &pca9539_defattr_group);
|
||||
return 0;
|
||||
}
|
||||
|
||||
static const struct i2c_device_id pca9539_id[] = {
|
||||
{ "pca9539", 0 },
|
||||
{ }
|
||||
};
|
||||
|
||||
static struct i2c_driver pca9539_driver = {
|
||||
.driver = {
|
||||
.name = "pca9539",
|
||||
},
|
||||
.probe = pca9539_probe,
|
||||
.remove = pca9539_remove,
|
||||
.id_table = pca9539_id,
|
||||
|
||||
.detect = pca9539_detect,
|
||||
.address_data = &addr_data,
|
||||
};
|
||||
|
||||
static int __init pca9539_init(void)
|
||||
{
|
||||
return i2c_add_driver(&pca9539_driver);
|
||||
}
|
||||
|
||||
static void __exit pca9539_exit(void)
|
||||
{
|
||||
i2c_del_driver(&pca9539_driver);
|
||||
}
|
||||
|
||||
MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>");
|
||||
MODULE_DESCRIPTION("PCA9539 driver");
|
||||
MODULE_LICENSE("GPL");
|
||||
|
||||
module_init(pca9539_init);
|
||||
module_exit(pca9539_exit);
|
||||
|
||||
Loading…
Reference in a new issue