hwmon: (w83791d) add manual PWM support
Add PWM manual control. Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl> Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean Delvare <khali@linux-fr.org>
This commit is contained in:
parent
6e1ecd9b8f
commit
6495ce1840
2 changed files with 75 additions and 7 deletions
|
@ -58,29 +58,32 @@ internal state that allows no clean access (Bank with ID register is not
|
|||
currently selected). If you know the address of the chip, use a 'force'
|
||||
parameter; this will put it into a more well-behaved state first.
|
||||
|
||||
The driver implements three temperature sensors, five fan rotation speed
|
||||
sensors, and ten voltage sensors.
|
||||
The driver implements three temperature sensors, ten voltage sensors,
|
||||
five fan rotation speed sensors and manual PWM control of each fan.
|
||||
|
||||
Temperatures are measured in degrees Celsius and measurement resolution is 1
|
||||
degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
|
||||
the temperature gets higher than the Overtemperature Shutdown value; it stays
|
||||
on until the temperature falls below the Hysteresis value.
|
||||
|
||||
Voltage sensors (also known as IN sensors) report their values in millivolts.
|
||||
An alarm is triggered if the voltage has crossed a programmable minimum
|
||||
or maximum limit.
|
||||
|
||||
Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
|
||||
triggered if the rotation speed has dropped below a programmable limit. Fan
|
||||
readings can be divided by a programmable divider (1, 2, 4, 8, 16,
|
||||
32, 64 or 128 for all fans) to give the readings more range or accuracy.
|
||||
|
||||
Voltage sensors (also known as IN sensors) report their values in millivolts.
|
||||
An alarm is triggered if the voltage has crossed a programmable minimum
|
||||
or maximum limit.
|
||||
Each fan controlled is controlled by PWM. The PWM duty cycle can be read and
|
||||
set for each fan separately. Valid values range from 0 (stop) to 255 (full).
|
||||
|
||||
The w83791d has a global bit used to enable beeping from the speaker when an
|
||||
alarm is triggered as well as a bitmask to enable or disable the beep for
|
||||
specific alarms. You need both the global beep enable bit and the
|
||||
corresponding beep bit to be on for a triggered alarm to sound a beep.
|
||||
|
||||
The sysfs interface to the gloabal enable is via the sysfs beep_enable file.
|
||||
The sysfs interface to the global enable is via the sysfs beep_enable file.
|
||||
This file is used for both legacy and new code.
|
||||
|
||||
The sysfs interface to the beep bitmask has migrated from the original legacy
|
||||
|
|
|
@ -23,7 +23,7 @@
|
|||
Supports following chips:
|
||||
|
||||
Chip #vin #fanin #pwm #temp wchipid vendid i2c ISA
|
||||
w83791d 10 5 3 3 0x71 0x5ca3 yes no
|
||||
w83791d 10 5 5 3 0x71 0x5ca3 yes no
|
||||
|
||||
The w83791d chip appears to be part way between the 83781d and the
|
||||
83792d. Thus, this file is derived from both the w83792d.c and
|
||||
|
@ -45,6 +45,7 @@
|
|||
#define NUMBER_OF_VIN 10
|
||||
#define NUMBER_OF_FANIN 5
|
||||
#define NUMBER_OF_TEMPIN 3
|
||||
#define NUMBER_OF_PWM 5
|
||||
|
||||
/* Addresses to scan */
|
||||
static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f,
|
||||
|
@ -116,6 +117,14 @@ static const u8 W83791D_REG_FAN_MIN[NUMBER_OF_FANIN] = {
|
|||
0xBD, /* FAN 5 Count Low Limit in DataSheet */
|
||||
};
|
||||
|
||||
static const u8 W83791D_REG_PWM[NUMBER_OF_PWM] = {
|
||||
0x81, /* PWM 1 duty cycle register in DataSheet */
|
||||
0x83, /* PWM 2 duty cycle register in DataSheet */
|
||||
0x94, /* PWM 3 duty cycle register in DataSheet */
|
||||
0xA0, /* PWM 4 duty cycle register in DataSheet */
|
||||
0xA1, /* PWM 5 duty cycle register in DataSheet */
|
||||
};
|
||||
|
||||
static const u8 W83791D_REG_FAN_CFG[2] = {
|
||||
0x84, /* FAN 1/2 configuration */
|
||||
0x95, /* FAN 3 configuration */
|
||||
|
@ -276,6 +285,9 @@ struct w83791d_data {
|
|||
two sensors with three values
|
||||
(cur, over, hyst) */
|
||||
|
||||
/* PWMs */
|
||||
u8 pwm[5]; /* pwm duty cycle */
|
||||
|
||||
/* Misc */
|
||||
u32 alarms; /* realtime status register encoding,combined */
|
||||
u8 beep_enable; /* Global beep enable */
|
||||
|
@ -653,6 +665,48 @@ static struct sensor_device_attribute sda_fan_alarm[] = {
|
|||
SENSOR_ATTR(fan5_alarm, S_IRUGO, show_alarm, NULL, 22),
|
||||
};
|
||||
|
||||
/* read/write PWMs */
|
||||
static ssize_t show_pwm(struct device *dev, struct device_attribute *attr,
|
||||
char *buf)
|
||||
{
|
||||
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
||||
int nr = sensor_attr->index;
|
||||
struct w83791d_data *data = w83791d_update_device(dev);
|
||||
return sprintf(buf, "%u\n", data->pwm[nr]);
|
||||
}
|
||||
|
||||
static ssize_t store_pwm(struct device *dev, struct device_attribute *attr,
|
||||
const char *buf, size_t count)
|
||||
{
|
||||
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
||||
struct i2c_client *client = to_i2c_client(dev);
|
||||
struct w83791d_data *data = i2c_get_clientdata(client);
|
||||
int nr = sensor_attr->index;
|
||||
unsigned long val;
|
||||
|
||||
if (strict_strtoul(buf, 10, &val))
|
||||
return -EINVAL;
|
||||
|
||||
mutex_lock(&data->update_lock);
|
||||
data->pwm[nr] = SENSORS_LIMIT(val, 0, 255);
|
||||
w83791d_write(client, W83791D_REG_PWM[nr], data->pwm[nr]);
|
||||
mutex_unlock(&data->update_lock);
|
||||
return count;
|
||||
}
|
||||
|
||||
static struct sensor_device_attribute sda_pwm[] = {
|
||||
SENSOR_ATTR(pwm1, S_IWUSR | S_IRUGO,
|
||||
show_pwm, store_pwm, 0),
|
||||
SENSOR_ATTR(pwm2, S_IWUSR | S_IRUGO,
|
||||
show_pwm, store_pwm, 1),
|
||||
SENSOR_ATTR(pwm3, S_IWUSR | S_IRUGO,
|
||||
show_pwm, store_pwm, 2),
|
||||
SENSOR_ATTR(pwm4, S_IWUSR | S_IRUGO,
|
||||
show_pwm, store_pwm, 3),
|
||||
SENSOR_ATTR(pwm5, S_IWUSR | S_IRUGO,
|
||||
show_pwm, store_pwm, 4),
|
||||
};
|
||||
|
||||
/* read/write the temperature1, includes measured value and limits */
|
||||
static ssize_t show_temp1(struct device *dev, struct device_attribute *devattr,
|
||||
char *buf)
|
||||
|
@ -917,6 +971,9 @@ static struct attribute *w83791d_attributes[] = {
|
|||
&sda_beep_ctrl[1].dev_attr.attr,
|
||||
&dev_attr_cpu0_vid.attr,
|
||||
&dev_attr_vrm.attr,
|
||||
&sda_pwm[0].dev_attr.attr,
|
||||
&sda_pwm[1].dev_attr.attr,
|
||||
&sda_pwm[2].dev_attr.attr,
|
||||
NULL
|
||||
};
|
||||
|
||||
|
@ -930,6 +987,8 @@ static const struct attribute_group w83791d_group = {
|
|||
static struct attribute *w83791d_attributes_fanpwm45[] = {
|
||||
FAN_UNIT_ATTRS(3),
|
||||
FAN_UNIT_ATTRS(4),
|
||||
&sda_pwm[3].dev_attr.attr,
|
||||
&sda_pwm[4].dev_attr.attr,
|
||||
NULL
|
||||
};
|
||||
|
||||
|
@ -1260,6 +1319,12 @@ static struct w83791d_data *w83791d_update_device(struct device *dev)
|
|||
for (i = 0; i < 3; i++)
|
||||
data->fan_div[i] |= (vbat_reg >> (3 + i)) & 0x04;
|
||||
|
||||
/* Update PWM duty cycle */
|
||||
for (i = 0; i < NUMBER_OF_PWM; i++) {
|
||||
data->pwm[i] = w83791d_read(client,
|
||||
W83791D_REG_PWM[i]);
|
||||
}
|
||||
|
||||
/* Update the first temperature sensor */
|
||||
for (i = 0; i < 3; i++) {
|
||||
data->temp1[i] = w83791d_read(client,
|
||||
|
|
Loading…
Reference in a new issue