[Blackfin] arch: merge ip0x-specific board changes

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>

arch/blackfin/Kconfig

@@ -249,7 +249,7 @@ config MEM_MT48LC8M32B2B5_7
 
 config MEM_MT48LC32M16A2TG_75
 	bool
-	depends on (BFIN527_EZKIT)
+	depends on (BFIN527_EZKIT || BFIN532_IP0X)
 	default y
 
 source "arch/blackfin/mach-bf527/Kconfig"
@@ -281,6 +281,7 @@ config CLKIN_HZ
 	default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS)
 	default "30000000" if BFIN561_EZKIT
 	default "24576000" if PNAV10
+	default "10000000" if BFIN532_IP0X
 	help
 	  The frequency of CLKIN crystal oscillator on the board in Hz.
 
@@ -304,6 +305,7 @@ config MEM_ADD_WIDTH
 	default 10 if BFIN537_STAMP
 	default 11 if BFIN533_STAMP
 	default 10 if PNAV10
+	default 10 if BFIN532_IP0X
 
 config PLL_BYPASS
 	bool "Bypass PLL"
@@ -450,6 +452,7 @@ config MEM_SIZE
 	default  64 if PNAV10
 	default  32 if H8606_HVSISTEMAS
 	default  64 if BFIN548_BLUETECHNIX_CM
+	default  64 if BFIN532_IP0X
 
 choice
 	prompt "DDR SDRAM Chip Type"

arch/blackfin/mach-bf533/boards/Kconfig

@@ -26,6 +26,12 @@ config H8606_HVSISTEMAS
 	help
 	  HV Sistemas H8606 board support.
 
+config BFIN532_IP0X
+	bool "IP04/IP08 IP-PBX"
+	depends on (BF532)
+	help
+	  Core support for IP04/IP04 open hardware IP-PBX.
+
 config GENERIC_BF533_BOARD
 	bool "Generic"
 	help

arch/blackfin/mach-bf533/boards/Makefile

@@ -4,6 +4,7 @@
 
 obj-$(CONFIG_GENERIC_BF533_BOARD)      += generic_board.o
 obj-$(CONFIG_BFIN533_STAMP)            += stamp.o
+obj-$(CONFIG_BFIN532_IP0X)             += ip0x.o
 obj-$(CONFIG_BFIN533_EZKIT)            += ezkit.o
 obj-$(CONFIG_BFIN533_BLUETECHNIX_CM)   += cm_bf533.o
 obj-$(CONFIG_H8606_HVSISTEMAS)         += H8606.o

arch/blackfin/mach-bf533/boards/ip0x.c

@@ -0,0 +1,279 @@
+/*
+ * File:         arch/blackfin/mach-bf533/ip0x.c
+ * Based on:     arch/blackfin/mach-bf533/bf1.c
+ * Based on:     arch/blackfin/mach-bf533/stamp.c
+ * Author:       Ivan Danov <idanov@gmail.com>
+ *               Modified for IP0X David Rowe
+ *
+ * Created:      2007
+ * Description:  Board info file for the IP04/IP08 boards, which
+ *               are derived from the BlackfinOne V2.0 boards.
+ *
+ * Modified:
+ *               COpyright 2007 David Rowe
+ *               Copyright 2006 Intratrade Ltd.
+ *               Copyright 2005 National ICT Australia (NICTA)
+ *               Copyright 2004-2006 Analog Devices Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#include <linux/usb/isp1362.h>
+#endif
+#include <asm/irq.h>
+#include <asm/bfin5xx_spi.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "IP04/IP08";
+
+/*
+ *  Driver needs to know address, irq and flag pin.
+ */
+#if defined(CONFIG_BFIN532_IP0X)
+#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+
+#include <linux/dm9000.h>
+
+static struct resource dm9000_resource1[] = {
+	{
+		.start = 0x20100000,
+		.end   = 0x20100000 + 1,
+		.flags = IORESOURCE_MEM
+	},{
+		.start = 0x20100000 + 2,
+		.end   = 0x20100000 + 3,
+		.flags = IORESOURCE_MEM
+	},{
+		.start = IRQ_PF15,
+		.end   = IRQ_PF15,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE
+	}
+};
+
+static struct resource dm9000_resource2[] = {
+	{
+		.start = 0x20200000,
+		.end   = 0x20200000 + 1,
+		.flags = IORESOURCE_MEM
+	},{
+		.start = 0x20200000 + 2,
+		.end   = 0x20200000 + 3,
+		.flags = IORESOURCE_MEM
+	},{
+		.start = IRQ_PF14,
+		.end   = IRQ_PF14,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE
+	}
+};
+
+/*
+* for the moment we limit ourselves to 16bit IO until some
+* better IO routines can be written and tested
+*/
+static struct dm9000_plat_data dm9000_platdata1 = {
+	.flags          = DM9000_PLATF_16BITONLY,
+};
+
+static struct platform_device dm9000_device1 = {
+	.name           = "dm9000",
+	.id             = 0,
+	.num_resources  = ARRAY_SIZE(dm9000_resource1),
+	.resource       = dm9000_resource1,
+	.dev            = {
+		.platform_data = &dm9000_platdata1,
+	}
+};
+
+static struct dm9000_plat_data dm9000_platdata2 = {
+	.flags          = DM9000_PLATF_16BITONLY,
+};
+
+static struct platform_device dm9000_device2 = {
+	.name           = "dm9000",
+	.id             = 1,
+	.num_resources  = ARRAY_SIZE(dm9000_resource2),
+	.resource       = dm9000_resource2,
+	.dev            = {
+		.platform_data = &dm9000_platdata2,
+	}
+};
+
+#endif
+#endif
+
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* all SPI peripherals info goes here */
+
+#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+/*
+ * CPOL (Clock Polarity)
+ *  0 - Active high SCK
+ *  1 - Active low SCK
+ *  CPHA (Clock Phase) Selects transfer format and operation mode
+ *  0 - SCLK toggles from middle of the first data bit, slave select
+ *      pins controlled by hardware.
+ *  1 - SCLK toggles from beginning of first data bit, slave select
+ *      pins controller by user software.
+ * 	.ctl_reg = 0x1c00,		 *  CPOL=1,CPHA=1,Sandisk 1G work
+ * NO NO	.ctl_reg = 0x1800,		 *  CPOL=1,CPHA=0
+ * NO NO	.ctl_reg = 0x1400,		 *  CPOL=0,CPHA=1
+ */
+	.ctl_reg = 0x1000,		/* CPOL=0,CPHA=0,Sandisk 1G work */
+	.enable_dma = 0,		/* if 1 - block!!! */
+	.bits_per_word = 8,
+	.cs_change_per_word = 0,
+};
+#endif
+
+/* Notice: for blackfin, the speed_hz is the value of register
+ * SPI_BAUD, not the real baudrate */
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+	{
+		.modalias = "spi_mmc",
+		.max_speed_hz = 2,
+		.bus_num = 1,
+		.chip_select = CONFIG_SPI_MMC_CS_CHAN,
+		.platform_data = NULL,
+		.controller_data = &spi_mmc_chip_info,
+	},
+#endif
+};
+
+/* SPI controller data */
+static struct bfin5xx_spi_master spi_bfin_master_info = {
+	.num_chipselect = 8,
+	.enable_dma = 1,  /* master has the ability to do dma transfer */
+};
+
+static struct platform_device spi_bfin_master_device = {
+	.name = "bfin-spi-master",
+	.id = 1, /* Bus number */
+	.dev = {
+		.platform_data = &spi_bfin_master_info, /* Passed to driver */
+	},
+};
+#endif  /* spi master and devices */
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+static struct resource bfin_uart_resources[] = {
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device bfin_uart_device = {
+	.name = "bfin-uart",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_uart_resources),
+	.resource = bfin_uart_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+static struct resource isp1362_hcd_resources[] = {
+	{
+		.start = 0x20300000,
+		.end   = 0x20300000 + 1,
+		.flags = IORESOURCE_MEM,
+	},{
+		.start = 0x20300000 + 2,
+		.end   = 0x20300000 + 3,
+		.flags = IORESOURCE_MEM,
+	},{
+		.start = IRQ_PF11,
+		.end   = IRQ_PF11,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct isp1362_platform_data isp1362_priv = {
+	.sel15Kres = 1,
+	.clknotstop = 0,
+	.oc_enable = 0,		/* external OC */
+	.int_act_high = 0,
+	.int_edge_triggered = 0,
+	.remote_wakeup_connected = 0,
+	.no_power_switching = 1,
+	.power_switching_mode = 0,
+};
+
+static struct platform_device isp1362_hcd_device = {
+	.name = "isp1362-hcd",
+	.id = 0,
+	.dev = {
+		.platform_data = &isp1362_priv,
+	},
+	.num_resources = ARRAY_SIZE(isp1362_hcd_resources),
+	.resource = isp1362_hcd_resources,
+};
+#endif
+
+
+static struct platform_device *ip0x_devices[] __initdata = {
+#if defined(CONFIG_BFIN532_IP0X)
+#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+	&dm9000_device1,
+	&dm9000_device2,
+#endif
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	&spi_bfin_master_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+	&bfin_uart_device,
+#endif
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+	&isp1362_hcd_device,
+#endif
+};
+
+static int __init ip0x_init(void)
+{
+	int i;
+
+	printk(KERN_INFO "%s(): registering device resources\n", __func__);
+	platform_add_devices(ip0x_devices, ARRAY_SIZE(ip0x_devices));
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	for (i = 0; i < ARRAY_SIZE(bfin_spi_board_info); ++i) {
+		int j = 1 << bfin_spi_board_info[i].chip_select;
+		/* set spi cs to 1 */
+		bfin_write_FIO_DIR(bfin_read_FIO_DIR() | j);
+		bfin_write_FIO_FLAG_S(j);
+	}
+	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+#endif
+
+	return 0;
+}
+
+arch_initcall(ip0x_init);

include/asm-blackfin/mach-bf533/mem_init.h

@@ -29,7 +29,8 @@
  * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
  */
 
-#if (CONFIG_MEM_MT48LC16M16A2TG_75 || CONFIG_MEM_MT48LC64M4A2FB_7E || CONFIG_MEM_GENERIC_BOARD)
+#if (CONFIG_MEM_MT48LC16M16A2TG_75 || CONFIG_MEM_MT48LC64M4A2FB_7E || \
+     CONFIG_MEM_MT48LC32M16A2TG_75 || CONFIG_MEM_GENERIC_BOARD)
 #if (CONFIG_SCLK_HZ > 119402985)
 #define SDRAM_tRP       TRP_2
 #define SDRAM_tRP_num   2
@@ -118,6 +119,13 @@
 #define SDRAM_CL    CL_3
 #endif
 
+#if (CONFIG_MEM_MT48LC32M16A2TG_75)
+  /*SDRAM INFORMATION: */
+#define SDRAM_Tref  64		/* Refresh period in milliseconds   */
+#define SDRAM_NRA   8192	/* Number of row addresses in SDRAM */
+#define SDRAM_CL    CL_3
+#endif
+
 #if (CONFIG_MEM_GENERIC_BOARD)
   /*SDRAM INFORMATION: Modify this for your board */
 #define SDRAM_Tref  64		/* Refresh period in milliseconds   */