media: dt-bindings: Add bindings for TDA1997X
Define the device tree bindings for the TDA1997X. Acked-by: Rob Herring <robh@kernel.org> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> [hans.verkuil@cisco.com: make a proper commit message] Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This commit is contained in:
Tim Harvey
Mauro Carvalho Chehab
parent
4cd9659ee9
commit
10c1d542c7
2 changed files with 252 additions and 0 deletions
178
Documentation/devicetree/bindings/media/i2c/tda1997x.txt
Normal file
178
Documentation/devicetree/bindings/media/i2c/tda1997x.txt
Normal file
|
|
@ -0,0 +1,178 @@
|
|||
Device-Tree bindings for the NXP TDA1997x HDMI receiver
|
||||
|
||||
The TDA19971/73 are HDMI video receivers.
|
||||
|
||||
The TDA19971 Video port output pins can be used as follows:
|
||||
- RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4]
|
||||
- YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4]
|
||||
- YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4]
|
||||
- YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2]
|
||||
- YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0]
|
||||
- YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles)
|
||||
- YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles)
|
||||
- YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
|
||||
|
||||
The TDA19973 Video port output pins can be used as follows:
|
||||
- RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0]
|
||||
- YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0]
|
||||
- YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0]
|
||||
- YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
|
||||
|
||||
The Video port output pins are mapped via 4-bit 'pin groups' allowing
|
||||
for a variety of connection possibilities including swapping pin order within
|
||||
pin groups. The video_portcfg device-tree property consists of register mapping
|
||||
pairs which map a chip-specific VP output register to a 4-bit pin group. If
|
||||
the pin group needs to be bit-swapped you can use the *_S pin-group defines.
|
||||
|
||||
Required Properties:
|
||||
- compatible :
|
||||
- "nxp,tda19971" for the TDA19971
|
||||
- "nxp,tda19973" for the TDA19973
|
||||
- reg : I2C slave address
|
||||
- interrupts : The interrupt number
|
||||
- DOVDD-supply : Digital I/O supply
|
||||
- DVDD-supply : Digital Core supply
|
||||
- AVDD-supply : Analog supply
|
||||
- nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups.
|
||||
|
||||
Optional Properties:
|
||||
- nxp,audout-format : DAI bus format: "i2s" or "spdif".
|
||||
- nxp,audout-width : width of audio output data bus (1-4).
|
||||
- nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used).
|
||||
- nxp,audout-mclk-fs : Multiplication factor between stream rate and codec
|
||||
mclk.
|
||||
|
||||
The port node shall contain one endpoint child node for its digital
|
||||
output video port, in accordance with the video interface bindings defined in
|
||||
Documentation/devicetree/bindings/media/video-interfaces.txt.
|
||||
|
||||
Optional Endpoint Properties:
|
||||
The following three properties are defined in video-interfaces.txt and
|
||||
are valid for the output parallel bus endpoint:
|
||||
- hsync-active: Horizontal synchronization polarity. Defaults to active high.
|
||||
- vsync-active: Vertical synchronization polarity. Defaults to active high.
|
||||
- data-active: Data polarity. Defaults to active high.
|
||||
|
||||
Examples:
|
||||
- VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422
|
||||
16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
|
||||
hdmi-receiver@48 {
|
||||
compatible = "nxp,tda19971";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_tda1997x>;
|
||||
reg = <0x48>;
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
|
||||
DOVDD-supply = <®_3p3v>;
|
||||
AVDD-supply = <®_1p8v>;
|
||||
DVDD-supply = <®_1p8v>;
|
||||
/* audio */
|
||||
#sound-dai-cells = <0>;
|
||||
nxp,audout-format = "i2s";
|
||||
nxp,audout-layout = <0>;
|
||||
nxp,audout-width = <16>;
|
||||
nxp,audout-mclk-fs = <128>;
|
||||
/*
|
||||
* The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
|
||||
* and Y[11:4] across 16bits in the same pixclk cycle.
|
||||
*/
|
||||
nxp,vidout-portcfg =
|
||||
/* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
|
||||
< TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
|
||||
/* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
|
||||
< TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
|
||||
/* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
|
||||
< TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
|
||||
/* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
|
||||
< TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
|
||||
|
||||
port {
|
||||
tda1997x_to_ipu1_csi0_mux: endpoint {
|
||||
remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
|
||||
bus-width = <16>;
|
||||
hsync-active = <1>;
|
||||
vsync-active = <1>;
|
||||
data-active = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
- VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
|
||||
16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
|
||||
hdmi-receiver@48 {
|
||||
compatible = "nxp,tda19971";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_tda1997x>;
|
||||
reg = <0x48>;
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
|
||||
DOVDD-supply = <®_3p3v>;
|
||||
AVDD-supply = <®_1p8v>;
|
||||
DVDD-supply = <®_1p8v>;
|
||||
/* audio */
|
||||
#sound-dai-cells = <0>;
|
||||
nxp,audout-format = "i2s";
|
||||
nxp,audout-layout = <0>;
|
||||
nxp,audout-width = <16>;
|
||||
nxp,audout-mclk-fs = <128>;
|
||||
/*
|
||||
* The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
|
||||
* and Y[11:4] across 16bits in the same pixclk cycle.
|
||||
*/
|
||||
nxp,vidout-portcfg =
|
||||
/* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
|
||||
< TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
|
||||
/* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
|
||||
< TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
|
||||
/* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
|
||||
< TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
|
||||
/* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
|
||||
< TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
|
||||
|
||||
port {
|
||||
tda1997x_to_ipu1_csi0_mux: endpoint {
|
||||
remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
|
||||
bus-width = <16>;
|
||||
hsync-active = <1>;
|
||||
vsync-active = <1>;
|
||||
data-active = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
- VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
|
||||
16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
|
||||
hdmi-receiver@48 {
|
||||
compatible = "nxp,tda19971";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_tda1997x>;
|
||||
reg = <0x48>;
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
|
||||
DOVDD-supply = <®_3p3v>;
|
||||
AVDD-supply = <®_1p8v>;
|
||||
DVDD-supply = <®_1p8v>;
|
||||
/* audio */
|
||||
#sound-dai-cells = <0>;
|
||||
nxp,audout-format = "i2s";
|
||||
nxp,audout-layout = <0>;
|
||||
nxp,audout-width = <16>;
|
||||
nxp,audout-mclk-fs = <128>;
|
||||
/*
|
||||
* The 8bpp BT656 mode outputs YCbCr[11:4] across 8bits over
|
||||
* 2 pixclk cycles.
|
||||
*/
|
||||
nxp,vidout-portcfg =
|
||||
/* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
|
||||
< TDA1997X_VP24_V15_12 TDA1997X_R_CR_CBCR_11_8 >,
|
||||
/* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
|
||||
< TDA1997X_VP24_V11_08 TDA1997X_R_CR_CBCR_7_4 >,
|
||||
|
||||
port {
|
||||
tda1997x_to_ipu1_csi0_mux: endpoint {
|
||||
remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
|
||||
bus-width = <16>;
|
||||
hsync-active = <1>;
|
||||
vsync-active = <1>;
|
||||
data-active = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
74
include/dt-bindings/media/tda1997x.h
Normal file
74
include/dt-bindings/media/tda1997x.h
Normal file
|
|
@ -0,0 +1,74 @@
|
|||
/* SPDX-License-Identifier: GPL-2.0 */
|
||||
/*
|
||||
* Copyright (C) 2017 Gateworks Corporation
|
||||
*/
|
||||
#ifndef _DT_BINDINGS_MEDIA_TDA1997X_H
|
||||
#define _DT_BINDINGS_MEDIA_TDA1997X_H
|
||||
|
||||
/* TDA19973 36bit Video Port control registers */
|
||||
#define TDA1997X_VP36_35_32 0
|
||||
#define TDA1997X_VP36_31_28 1
|
||||
#define TDA1997X_VP36_27_24 2
|
||||
#define TDA1997X_VP36_23_20 3
|
||||
#define TDA1997X_VP36_19_16 4
|
||||
#define TDA1997X_VP36_15_12 5
|
||||
#define TDA1997X_VP36_11_08 6
|
||||
#define TDA1997X_VP36_07_04 7
|
||||
#define TDA1997X_VP36_03_00 8
|
||||
|
||||
/* TDA19971 24bit Video Port control registers */
|
||||
#define TDA1997X_VP24_V23_20 0
|
||||
#define TDA1997X_VP24_V19_16 1
|
||||
#define TDA1997X_VP24_V15_12 3
|
||||
#define TDA1997X_VP24_V11_08 4
|
||||
#define TDA1997X_VP24_V07_04 6
|
||||
#define TDA1997X_VP24_V03_00 7
|
||||
|
||||
/* Pin groups */
|
||||
#define TDA1997X_VP_OUT_EN 0x80 /* enable output group */
|
||||
#define TDA1997X_VP_HIZ 0x40 /* hi-Z output group when not used */
|
||||
#define TDA1997X_VP_SWP 0x10 /* pin-swap output group */
|
||||
#define TDA1997X_R_CR_CBCR_3_0 (0 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
|
||||
#define TDA1997X_R_CR_CBCR_7_4 (1 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
|
||||
#define TDA1997X_R_CR_CBCR_11_8 (2 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
|
||||
#define TDA1997X_B_CB_3_0 (3 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
|
||||
#define TDA1997X_B_CB_7_4 (4 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
|
||||
#define TDA1997X_B_CB_11_8 (5 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
|
||||
#define TDA1997X_G_Y_3_0 (6 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
|
||||
#define TDA1997X_G_Y_7_4 (7 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
|
||||
#define TDA1997X_G_Y_11_8 (8 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
|
||||
/* pinswapped groups */
|
||||
#define TDA1997X_R_CR_CBCR_3_0_S (TDA1997X_R_CR_CBCR_3_0 | TDA1997X_VP_SWAP)
|
||||
#define TDA1997X_R_CR_CBCR_7_4_S (TDA1997X_R_CR_CBCR_7_4 | TDA1997X_VP_SWAP)
|
||||
#define TDA1997X_R_CR_CBCR_11_8_S (TDA1997X_R_CR_CBCR_11_8 | TDA1997X_VP_SWAP)
|
||||
#define TDA1997X_B_CB_3_0_S (TDA1997X_B_CB_3_0 | TDA1997X_VP_SWAP)
|
||||
#define TDA1997X_B_CB_7_4_S (TDA1997X_B_CB_7_4 | TDA1997X_VP_SWAP)
|
||||
#define TDA1997X_B_CB_11_8_S (TDA1997X_B_CB_11_8 | TDA1997X_VP_SWAP)
|
||||
#define TDA1997X_G_Y_3_0_S (TDA1997X_G_Y_3_0 | TDA1997X_VP_SWAP)
|
||||
#define TDA1997X_G_Y_7_4_S (TDA1997X_G_Y_7_4 | TDA1997X_VP_SWAP)
|
||||
#define TDA1997X_G_Y_11_8_S (TDA1997X_G_Y_11_8 | TDA1997X_VP_SWAP)
|
||||
|
||||
/* Audio bus DAI format */
|
||||
#define TDA1997X_I2S16 1 /* I2S 16bit */
|
||||
#define TDA1997X_I2S32 2 /* I2S 32bit */
|
||||
#define TDA1997X_SPDIF 3 /* SPDIF */
|
||||
#define TDA1997X_OBA 4 /* One Bit Audio */
|
||||
#define TDA1997X_DST 5 /* Direct Stream Transfer */
|
||||
#define TDA1997X_I2S16_HBR 6 /* HBR straight in I2S 16bit mode */
|
||||
#define TDA1997X_I2S16_HBR_DEMUX 7 /* HBR demux in I2S 16bit mode */
|
||||
#define TDA1997X_I2S32_HBR_DEMUX 8 /* HBR demux in I2S 32bit mode */
|
||||
#define TDA1997X_SPDIF_HBR_DEMUX 9 /* HBR demux in SPDIF mode */
|
||||
|
||||
/* Audio bus channel layout */
|
||||
#define TDA1997X_LAYOUT0 0 /* 2-channel */
|
||||
#define TDA1997X_LAYOUT1 1 /* 8-channel */
|
||||
|
||||
/* Audio bus clock */
|
||||
#define TDA1997X_ACLK_16FS 0
|
||||
#define TDA1997X_ACLK_32FS 1
|
||||
#define TDA1997X_ACLK_64FS 2
|
||||
#define TDA1997X_ACLK_128FS 3
|
||||
#define TDA1997X_ACLK_256FS 4
|
||||
#define TDA1997X_ACLK_512FS 5
|
||||
|
||||
#endif /* _DT_BINDINGS_MEDIA_TDA1997X_H */
|
||||
Loading…
Reference in a new issue