2006-12-24 14:46:55 -07:00
|
|
|
/*
|
2007-07-11 12:04:50 -06:00
|
|
|
* linux/drivers/mmc/core/sd_ops.h
|
2006-12-24 14:46:55 -07:00
|
|
|
*
|
|
|
|
|
* Copyright 2006-2007 Pierre Ossman
|
|
|
|
|
*
|
|
|
|
|
* This program is free software; you can redistribute it and/or modify
|
|
|
|
|
* it under the terms of the GNU General Public License as published by
|
|
|
|
|
* the Free Software Foundation; either version 2 of the License, or (at
|
|
|
|
|
* your option) any later version.
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
#ifndef _MMC_SD_OPS_H
|
|
|
|
|
#define _MMC_SD_OPS_H
|
|
|
|
|
|
|
|
|
|
int mmc_app_set_bus_width(struct mmc_card *card, int width);
|
|
|
|
|
int mmc_send_app_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr);
|
|
|
|
|
int mmc_send_if_cond(struct mmc_host *host, u32 ocr);
|
|
|
|
|
int mmc_send_relative_addr(struct mmc_host *host, unsigned int *rca);
|
|
|
|
|
int mmc_app_send_scr(struct mmc_card *card, u32 *scr);
|
|
|
|
|
int mmc_sd_switch(struct mmc_card *card, int mode, int group,
|
|
|
|
|
u8 value, u8 *resp);
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 15:17:46 -06:00
|
|
|
int mmc_app_sd_status(struct mmc_card *card, void *ssr);
|
2006-12-24 14:46:55 -07:00
|
|
|
|
|
|
|
|
#endif
|
|
|
|
|
|
